Oh and just for interest. Boot a Pi3 with Linux raspberrypi 5.10.17-v7+ and nothing in the USB port and screen shows up as expected. Plug same 4 port hub with the connect the the USB switch and a 4GB USB drive. Then press the button to change from workstation to Pi and about 5 seconds later the mouse and keyboard work nd in the /media/pi/Transcend are the files on the USB drive.
On the Beagle the little blue LED on the USB drive doesn't even light up. I kind of think the BBB should be able to do this too. Thanks John > -----Original Message----- > From: [email protected] [mailto:[email protected]] On > Behalf Of John Dammeyer > Sent: May-16-21 6:47 PM > To: 'Beagle Board' > Subject: RE: [beagleboard] Configure CAN0 with buildroot > > > > > -----Original Message----- > > From: Robert Nelson [mailto:[email protected]] > > > I moved the MicroSD card over to the other Beagle. Booted and USB mouse > > > and keyboard (Logitech wireless) work. The Logitech > > wireless was not discovered on the other Beagle. > > > > > > I think it may be sick. > > > > > > From the descriptions on https://beagleboard.org/latest-images I can't > > > figure out what the latest graphical desktop image is for > the > > BBB. > > > > There really isn't an official lxqt release, it just was too un-useful: > > > > https://rcn-ee.net/rootfs/bb.org/testing/2021-04-27/ > > > > Regards, > > > > -- > > Robert Nelson > > Been an interesting weekend with many different versions flashed (or > sometimes not) into the eMMC. > I have this currently running well from the 32MB SD card from the img link > above. > debian@beaglebone:~$ uname -a > Linux beaglebone 4.19.94-ti-r63 #1buster SMP PREEMPT Fri May 14 16:42:32 UTC > 2021 armv7l GNU/Linux > > There is on issue I've run into that has caused a lot of grief and retries. > That's the behavior of the USB port on and after boot. > I have two monitors and an IOGEAR GUS402 USB 2.0 peripheral sharing device. > Press a button and it switches the keyboard and > mouse between my main workstation and whatever module I'm currently working > on; BBB, Pi3, Pi4, PiZeroW. > Between that and the BBB I've been using a 4 port USB hub. One from ANKER > which is a USB 3.0 hub and one from INSIGNIA a 4 port > USB 2.0 hub with separate power adaptor. The BBB doesn't like the 3.0 hub > very much. > > Using the 4 port USB 2.0 hub if the IOGEAR isn't switched to present the > keyboard and mouse to the Beagle during boot after that, > although the screen shows the desktop, the mouse pointer remains in the > middle of the screen and mouse and keyboard don't work. > > If I've booted with the switch set so the keyboard and mouse are visible to > the BBB then after that I can switch back and forth > between the workstation and the beagle. > > I've attached the serial port boot log and also the dmesg log that shows usb > isn't ready. What's missing so that it will find a usb device > when it's plugged in? > > Thanks > John > > > -- > For more options, visit http://beagleboard.org/discuss > --- > You received this message because you are subscribed to the Google Groups > "BeagleBoard" group. > To unsubscribe from this group and stop receiving emails from it, send an > email to [email protected]. > To view this discussion on the web visit > https://groups.google.com/d/msgid/beagleboard/0e6201d74abe%2486225e80%2492671b80%24%40autoartisans.com. -- For more options, visit http://beagleboard.org/discuss --- You received this message because you are subscribed to the Google Groups "BeagleBoard" group. To unsubscribe from this group and stop receiving emails from it, send an email to [email protected]. To view this discussion on the web visit https://groups.google.com/d/msgid/beagleboard/0e6901d74abf%24c5f02e60%2451d08b20%24%40autoartisans.com.
