Hello,
I'm having trouble getting my Pinnacle PCTV Pro to work, which I
bought in the Netherlands (europe) a few (2?) years ago.
After loading bttv I only get snow on the top of the screen..
everything below that seems to be frozen in a certain state.
Any help would be greatly appreciated. Various system output:
Custom compiled kernel, no patches 2.6.13.4
lspci -v:
0000:00:0b.0 Multimedia video controller: Brooktree Corporation Bt878
Video Capture (rev 11)
Subsystem: Pinnacle Systems Inc. PCTV pro (TV + FM stereo receiver)
Flags: bus master, medium devsel, latency 64, IRQ 5
Memory at cddfe000 (32-bit, prefetchable) [size=4K]
Capabilities: [44] Vital Product Data
Capabilities: [4c] Power Management version 2
Chips on the Card:
Conexant Fusion 878a
Micronas MSP 3410G B11
Philips TDA 9886TS
?? Microtune MT 2032 ??
Model: EMPTYV-51013170-1.4
The above info matches everything on my board, as far as I can tell.
Got this from a site. Couldn't see anything on my board about the MT
2032 however.
dmesg:
bttv: driver version 0.9.16 loaded
bttv: using 8 buffers with 2080k (520 pages) each for capture
bttv: Bt8xx card found (0).
ACPI: PCI Interrupt 0000:00:0b.0[A] -> Link [LNKB] -> GSI 5 (level,
low) -> IRQ 5
bttv0: Bt878 (rev 17) at 0000:00:0b.0, irq: 5, latency: 64, mmio: 0xcddfe000
bttv0: detected: Pinnacle PCTV [card=39], PCI subsystem ID is 11bd:0012
bttv0: using: Pinnacle PCTV Studio/Rave [card=39,insmod option]
bttv0: gpio: en=00000000, out=00000000 in=00fffbdf [init]
bttv0: i2c: checking for MSP34xx @ 0x80... found
bttv0: pinnacle/mt: id=2 info="PAL+SECAM / stereo" radio=yes
bttv0: using tuner=33
bttv0: i2c: checking for MSP34xx @ 0x80... found
msp34xx: init: chip=MSP3410G-B11 +nicam +simple +simpler +radio mode=simpler
msp34xxg: daemon started
bttv0: i2c: checking for TDA9875 @ 0xb0... not found
bttv0: i2c: checking for TDA7432 @ 0x8a... not found
tda9885/6/7: chip found @ 0x86
: chip found @ 0xc0 (bt878 #0 [sw])
: Returned more than 5 bytes. It is not a TEA5767
tuner 0-0060: microtune: companycode=4d54 part=04 rev=04
tuner 0-0060: microtune MT2032 found, OK
bttv0: registered device video0
bttv0: registered device vbi0
bttv0: registered device radio0
bttv0: PLL: 28636363 => 35468950 . ok
tuner 0-0060: MT2032 Fatal Error: PLLs didn't lock.
modules (removed all the obvious stuff):
Module Size Used by
tuner 37864 0
tda9887 13648 0
msp3400 26272 0
bttv 163280 0
i2c_algo_bit 9736 1 bttv
v4l2_common 5888 1 bttv
tveeprom 11856 1 bttv
i2c_core 21648 6 tuner,tda9887,msp3400,bttv,i2c_algo_bit,tveeprom
video 16196 0
analog 12128 0
pcspkr 3480 0
rtc 12472 0
mii 5760 1 3c59x
video_buf 21956 1 bttv
btcx_risc 5064 1 bttv
videodev 9600 1 bttv
generic 4484 0 [permanent]
evdev 9600 0
One thing that seems to be wrong is this: "tuner 0-0060: MT2032 Fatal
Error: PLLs didn't lock.", but googling on it doesn't provide any
useful info.
Regards,
William Leese
