The file as you download it is compressed in ".xz" format. What are you using to un-compress the file to an ".img" file?
I recommend you use Etcher to install the image on the uSD card. I don't think "Win32Diskimager" is recommended for BeagleBoards any longer. Etcher will automatically verify the image as written is correct and complete, including the Linux file system. You don't need to format it. And for sure, do not format it after you write the image to the card with Etcher. That will erase the card. Just eject it and put it in the BBB after you image it. Make sure the card is fully seated, and not sitting sticking out on the eject spring. Are you sure the BBB is good? Do you have a good power supply running the BBB? The high current peaks during booting require at least a 1 Amp supply, preferably a 1.5 Amp supply. Too weak a power supply will cause it to hang during booting. How old is the version of software in the Flash memory on board the BBB? Will it boot from the on-board memory, without a uSD card installed? --- Graham == On Wednesday, June 26, 2019 at 7:48:04 PM UTC-5, [email protected] wrote: > > Thanks for your answer! I'm trying to install an image on the uSD and i > want to run from that uSD card. i downloaded "Debian 9.5 2018-10-07 4GB SD > LXQT" and i tried to write that on uSD with "Win32DiskImager". I formated > my SD with "SD card formatter" such as Dennis Lee Bieber said but it > failed and i tried with a new SD this process, but it's failed again.I > don't know what to do,really!! please help me! > > On Wednesday, June 26, 2019 at 11:43:00 PM UTC+4:30, [email protected] > wrote: >> >> The message "You need to format the disk in drive E: before you can use >> it" means that Windows can not read the file system on the uSD card. >> Well, Windows can not read Linux file systems, so this is OK, and you >> should ignore the message. >> >> The ".img" file and Etcher will install a Linux file system on the card. >> >> Are you trying to install an image on the uSD card, so that you run from >> the uSD card? >> Or, are you trying to install a flasher on the uSD card so that the uSD >> card will install the image in the Flash memory on the BBB? >> >> Make sure you are using the correct image file to do what you are trying >> to do. >> >> Is Etcher providing any errors? If so, what does it say? >> If Etcher does not report any errors, do not reformat the card like >> Windows says, and just put the Etcher programmed card in the BBB and run it. >> >> --- Graham >> >> == >> >> On Wednesday, June 26, 2019 at 7:53:43 AM UTC-5, [email protected] >> wrote: >>> >>> Hello, i have a beaglebone black board. i want to use "Debian 9.5 >>> 2018-10-07 4GB SD LXQT" os image for it, i downloaded it from >>> http://beagleboard.org/latest-images/ >>> <http://www.google.com/url?q=http%3A%2F%2Fbeagleboard.org%2Flatest-images%2F&sa=D&sntz=1&usg=AFQjCNFoQN49dLQsMdU09qzUc4Nq9v3C9Q> >>> and >>> i try to write it on micro SD with "balena etcher" but it cann't write >>> correctly, i repeat this process over and over and i deal with "You need to >>> format the disk in drive E: before you can use it" any time. >>> 14 daya ago, i did this process successfully, but my micro SD damaged >>> and i have to change it, after that i have above problem. >>> i did this process with other os images, too but i had this problem, >>> again. >>> please help me! give me a solution! >>> >> -- For more options, visit http://beagleboard.org/discuss --- You received this message because you are subscribed to the Google Groups "BeagleBoard" group. To unsubscribe from this group and stop receiving emails from it, send an email to [email protected]. To view this discussion on the web visit https://groups.google.com/d/msgid/beagleboard/ef4788aa-65ca-4b77-8e55-2e1f0a3ff007%40googlegroups.com. For more options, visit https://groups.google.com/d/optout.
