Not strange at all. One of the two devices is in loopback mode, and my first guess would be the 600. Fix that first, then muck with the parameters in zapata.conf.
------------------------ > Thats really strange, > one side has to be pri_net and the other pri_cpe always, no matter what > devices you use (cisco, asterisk, nortel, ericsson, etc.) > If you set asterisk as pri_cpe, and it says the other side is also configured > as pri_cpe, change it to pri_net. > If it also says that the other side is configured for pri_net, then there > must be something wrong with your adit600. Try checking > the configuration of the adit600. > > Argentilinux > > Tom Hayden escribi�: > > I Changed it to pri_net and get the following error now: > > Jun 6 08:52:17 WARNING[3438]: chan_zap.c:7970 pri_dchannel: PRI > Error: We think we're the network, but they think they're the network, > too. > > Any ideas? > > -- > Tom > > On 6/6/05, Gustavo Alvarez <[EMAIL PROTECTED]> wrote: > > > The problem is that both adit600 and Asterisk box are configured as > clock slaves (pri_cpe). > Change pri_cpe to pri_net in your zapata.conf, and your asterisk box > would be the clock source. > It should work. Good Luck. > > Argentilinux. > > Tom Hayden escribi�: > > > > Hello > I just installed a TE110P in a Dell Poweredge 750 (rackmount), > which > is connected via crossover T1 cable to a adit 600. Anyway, I've > encountered an array of errors, which I believe I have narrowed > down > to the 22 IRQ misses I encounter on zttool. I've noticed that the > te110p and the usb device share an IRQ. Could that be the source > of my > woes? Would disabling the usb device in the bios solve my > problems or > could it be my configuration? > > -- Errors generated by asterisk > chan_zap.c:7970 pri_dchannel: PRI Error: We think we're the CPE, > but > they think they're the CPE too. > > ---zaptel.conf > defaultzone=us > span=1,1,0,esf,b8zs > bchan=1-23 > dchan=24 > loadzone=us > > -- zapata.conf (relevant portions) > signalling = pri_cpe > switchtype = national > group = 2 > context = fxoout > cidsignalling = dtmf > cidstart = polarity > channel => 1-23 > > -- proc/interrupts > CPU0 > 0: 6334299 IO-APIC-edge timer > 1: 14390 IO-APIC-edge keyboard > 2: 0 XT-PIC cascade > 8: 3 IO-APIC-edge rtc > 14: 2 IO-APIC-edge ide0 > 15: 505440 IO-APIC-edge ide1 > 21: 150019 IO-APIC-level eth1 > 22: 63326503 IO-APIC-level t1xxp > > -- lspci -bv | grep IRQ > Flags: bus master, medium devsel, latency 0, IRQ 11 > Flags: bus master, medium devsel, latency 0, IRQ 10 (USB) > Flags: bus master, fast devsel, latency 0, IRQ 255 > Flags: bus master, medium devsel, latency 0, IRQ 7 > Flags: medium devsel, IRQ 5 > Flags: bus master, 66Mhz, medium devsel, latency 0, IRQ 3 > Flags: bus master, 66Mhz, medium devsel, latency 32, IRQ 11 > Flags: bus master, medium devsel, latency 32, IRQ 10 > (**TE110P**) > Flags: bus master, VGA palette snoop, stepping, medium > devsel, > latency 32, IRQ 255 > > Thanks in Advance, > > > > > > ---------------End of Original Message----------------- _______________________________________________ Asterisk-Users mailing list [email protected] http://lists.digium.com/mailman/listinfo/asterisk-users To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users
