If you can still login you can do set2default That will set it to factory defaults all your config info is now gone you must re-provision with all the slot nonsense (the default user name is �admin,� the default password is �zhone�): I have an old working config for a 24fxs zhone in format used by its tftp loader use at your own risk..
IF you't dont have a tftp server then grab one from here http://www.jbmelectronics.com/tftp.htm my old notes says... after factory default config ..enter following cmds #load new IP definition & enter ip/net mask new ip-interface-record 1/1/1/0/ip #save the ip config update ip-interface-record 1/1/1/0/ip #check it is correct get ip-interface-record 1/1/1/0/ip #connect to yout tftp server & load config from txt file restore network <IP of your tftp server> zplexfxs.txt I might have missed some thing that is obvious, :) -----Original Message----- From: Eris Riswanto <[EMAIL PROTECTED]> To: [EMAIL PROTECTED] <[EMAIL PROTECTED]> Date: March 31, 2003 5:30 PM Subject: Re: [Asterisk-Users] Serious problem with z-plex 10 > >|Do not plug in ethernet cable at all, even if the interface is down. >| >|The long time to come up is due to the software being verified, and then >|booted. It is that way on many channel banks. >| >|Also it could mean the zplex is not happy with the line coding it is >|getting. It is a very sensitive device and flakes out if it doesn't get >|good signal. >|-- >|Steven Critchfield <[EMAIL PROTECTED]> >| > >The ethernet port from the device doesn't even connected to network. >But i did configure the ethernet interface. I think the device >mess up with the network configuration. >How can i get back the device to original configuration? >Anybody experienced with it, or any good idea to fix this problem? > >Thanks in advance > >Eris Riswanto > >_______________________________________________ >Asterisk-Users mailing list >[EMAIL PROTECTED] >http://lists.digium.com/mailman/listinfo/asterisk-users
create if-translate 1/1/1/0/18 set ifindex = 1 set shelf = 1 set slot = 1 set port = 1 set subport = 0 set type = ds1 set adminstatus = up commit if-translate 1/1/1/0/18 create if-translate 1/1/2/0/18 set ifindex = 2 set shelf = 1 set slot = 1 set port = 2 set subport = 0 set type = ds1 set adminstatus = down commit if-translate 1/1/2/0/18 create if-translate 1/1/1/0/102 set ifindex = 3 set shelf = 1 set slot = 1 set port = 1 set subport = 0 set type = voicefxs set adminstatus = up commit if-translate 1/1/1/0/102 create if-translate 1/1/2/0/102 set ifindex = 4 set shelf = 1 set slot = 1 set port = 2 set subport = 0 set type = voicefxs set adminstatus = up commit if-translate 1/1/2/0/102 create if-translate 1/1/3/0/102 set ifindex = 5 set shelf = 1 set slot = 1 set port = 3 set subport = 0 set type = voicefxs set adminstatus = up commit if-translate 1/1/3/0/102 create if-translate 1/1/4/0/102 set ifindex = 6 set shelf = 1 set slot = 1 set port = 4 set subport = 0 set type = voicefxs set adminstatus = up commit if-translate 1/1/4/0/102 create if-translate 1/1/5/0/102 set ifindex = 7 set shelf = 1 set slot = 1 set port = 5 set subport = 0 set type = voicefxs set adminstatus = up commit if-translate 1/1/5/0/102 create if-translate 1/1/6/0/102 set ifindex = 8 set shelf = 1 set slot = 1 set port = 6 set subport = 0 set type = voicefxs set adminstatus = up commit if-translate 1/1/6/0/102 create if-translate 1/1/7/0/102 set ifindex = 9 set shelf = 1 set slot = 1 set port = 7 set subport = 0 set type = voicefxs set adminstatus = up commit if-translate 1/1/7/0/102 create if-translate 1/1/8/0/102 set ifindex = 10 set shelf = 1 set slot = 1 set port = 8 set subport = 0 set type = voicefxs set adminstatus = up commit if-translate 1/1/8/0/102 create if-translate 1/1/9/0/102 set ifindex = 11 set shelf = 1 set slot = 1 set port = 9 set subport = 0 set type = voicefxs set adminstatus = up commit if-translate 1/1/9/0/102 create if-translate 1/1/10/0/102 set ifindex = 12 set shelf = 1 set slot = 1 set port = 10 set subport = 0 set type = voicefxs set adminstatus = up commit if-translate 1/1/10/0/102 create if-translate 1/1/11/0/102 set ifindex = 13 set shelf = 1 set slot = 1 set port = 11 set subport = 0 set type = voicefxs set adminstatus = up commit if-translate 1/1/11/0/102 create if-translate 1/1/12/0/102 set ifindex = 14 set shelf = 1 set slot = 1 set port = 12 set subport = 0 set type = voicefxs set adminstatus = up commit if-translate 1/1/12/0/102 create if-translate 1/1/13/0/102 set ifindex = 15 set shelf = 1 set slot = 1 set port = 13 set subport = 0 set type = voicefxs set adminstatus = up commit if-translate 1/1/13/0/102 create if-translate 1/1/14/0/102 set ifindex = 16 set shelf = 1 set slot = 1 set port = 14 set subport = 0 set type = voicefxs set adminstatus = up commit if-translate 1/1/14/0/102 create if-translate 1/1/15/0/102 set ifindex = 17 set shelf = 1 set slot = 1 set port = 15 set subport = 0 set type = voicefxs set adminstatus = up commit if-translate 1/1/15/0/102 create if-translate 1/1/16/0/102 set ifindex = 18 set shelf = 1 set slot = 1 set port = 16 set subport = 0 set type = voicefxs set adminstatus = up commit if-translate 1/1/16/0/102 create if-translate 1/1/17/0/102 set ifindex = 19 set shelf = 1 set slot = 1 set port = 17 set subport = 0 set type = voicefxs set adminstatus = up commit if-translate 1/1/17/0/102 create if-translate 1/1/18/0/102 set ifindex = 20 set shelf = 1 set slot = 1 set port = 18 set subport = 0 set type = voicefxs set adminstatus = up commit if-translate 1/1/18/0/102 create if-translate 1/1/19/0/102 set ifindex = 21 set shelf = 1 set slot = 1 set port = 19 set subport = 0 set type = voicefxs set adminstatus = up commit if-translate 1/1/19/0/102 create if-translate 1/1/20/0/102 set ifindex = 22 set shelf = 1 set slot = 1 set port = 20 set subport = 0 set type = voicefxs set adminstatus = up commit if-translate 1/1/20/0/102 create if-translate 1/1/21/0/102 set ifindex = 23 set shelf = 1 set slot = 1 set port = 21 set subport = 0 set type = voicefxs set adminstatus = up commit if-translate 1/1/21/0/102 create if-translate 1/1/22/0/102 set ifindex = 24 set shelf = 1 set slot = 1 set port = 22 set subport = 0 set type = voicefxs set adminstatus = up commit if-translate 1/1/22/0/102 create if-translate 1/1/23/0/102 set ifindex = 25 set shelf = 1 set slot = 1 set port = 23 set subport = 0 set type = voicefxs set adminstatus = up commit if-translate 1/1/23/0/102 create if-translate 1/1/24/0/102 set ifindex = 26 set shelf = 1 set slot = 1 set port = 24 set subport = 0 set type = voicefxs set adminstatus = up commit if-translate 1/1/24/0/102 create if-translate 1/1/1/0/6 set ifindex = 27 set shelf = 1 set slot = 1 set port = 1 set subport = 0 set type = ethernetcsmacd set adminstatus = up commit if-translate 1/1/1/0/6 create if-translate 1/1/1/0/126 set ifindex = 28 set shelf = 1 set slot = 1 set port = 1 set subport = 0 set type = ip set adminstatus = up commit if-translate 1/1/1/0/126 create analog-fxs-cfg-profile 1/1/1/0/102 set signal-type = fxsloopstart set ring-frequency = ringfrequency20 set ring-back = off commit analog-fxs-cfg-profile 1/1/1/0/102 create analog-fxs-cfg-profile 1/1/2/0/102 set signal-type = fxsloopstart set ring-frequency = ringfrequency20 set ring-back = off commit analog-fxs-cfg-profile 1/1/2/0/102 create analog-fxs-cfg-profile 1/1/3/0/102 set signal-type = fxsloopstart set ring-frequency = ringfrequency20 set ring-back = off commit analog-fxs-cfg-profile 1/1/3/0/102 create analog-fxs-cfg-profile 1/1/4/0/102 set signal-type = fxsloopstart set ring-frequency = ringfrequency20 set ring-back = off commit analog-fxs-cfg-profile 1/1/4/0/102 create analog-fxs-cfg-profile 1/1/5/0/102 set signal-type = fxsloopstart set ring-frequency = ringfrequency20 set ring-back = off commit analog-fxs-cfg-profile 1/1/5/0/102 create analog-fxs-cfg-profile 1/1/6/0/102 set signal-type = fxsloopstart set ring-frequency = ringfrequency20 set ring-back = off commit analog-fxs-cfg-profile 1/1/6/0/102 create analog-fxs-cfg-profile 1/1/7/0/102 set signal-type = fxsloopstart set ring-frequency = ringfrequency20 set ring-back = off commit analog-fxs-cfg-profile 1/1/7/0/102 create analog-fxs-cfg-profile 1/1/8/0/102 set signal-type = fxsloopstart set ring-frequency = ringfrequency20 set ring-back = off commit analog-fxs-cfg-profile 1/1/8/0/102 create analog-fxs-cfg-profile 1/1/9/0/102 set signal-type = fxsloopstart set ring-frequency = ringfrequency20 set ring-back = off commit analog-fxs-cfg-profile 1/1/9/0/102 create analog-fxs-cfg-profile 1/1/10/0/102 set signal-type = fxsloopstart set ring-frequency = ringfrequency20 set ring-back = off commit analog-fxs-cfg-profile 1/1/10/0/102 create analog-fxs-cfg-profile 1/1/11/0/102 set signal-type = fxsloopstart set ring-frequency = ringfrequency20 set ring-back = off commit analog-fxs-cfg-profile 1/1/11/0/102 create analog-fxs-cfg-profile 1/1/12/0/102 set signal-type = fxsloopstart set ring-frequency = ringfrequency20 set ring-back = off commit analog-fxs-cfg-profile 1/1/12/0/102 create analog-fxs-cfg-profile 1/1/13/0/102 set signal-type = fxsloopstart set ring-frequency = ringfrequency20 set ring-back = off commit analog-fxs-cfg-profile 1/1/13/0/102 create analog-fxs-cfg-profile 1/1/14/0/102 set signal-type = fxsloopstart set ring-frequency = ringfrequency20 set ring-back = off commit analog-fxs-cfg-profile 1/1/14/0/102 create analog-fxs-cfg-profile 1/1/15/0/102 set signal-type = fxsloopstart set ring-frequency = ringfrequency20 set ring-back = off commit analog-fxs-cfg-profile 1/1/15/0/102 create analog-fxs-cfg-profile 1/1/16/0/102 set signal-type = fxsloopstart set ring-frequency = ringfrequency20 set ring-back = off commit analog-fxs-cfg-profile 1/1/16/0/102 create analog-fxs-cfg-profile 1/1/17/0/102 set signal-type = fxsloopstart set ring-frequency = ringfrequency20 set ring-back = off commit analog-fxs-cfg-profile 1/1/17/0/102 create analog-fxs-cfg-profile 1/1/18/0/102 set signal-type = fxsloopstart set ring-frequency = ringfrequency20 set ring-back = off commit analog-fxs-cfg-profile 1/1/18/0/102 create analog-fxs-cfg-profile 1/1/19/0/102 set signal-type = fxsloopstart set ring-frequency = ringfrequency20 set ring-back = off commit analog-fxs-cfg-profile 1/1/19/0/102 create analog-fxs-cfg-profile 1/1/20/0/102 set signal-type = fxsloopstart set ring-frequency = ringfrequency20 set ring-back = off commit analog-fxs-cfg-profile 1/1/20/0/102 create analog-fxs-cfg-profile 1/1/21/0/102 set signal-type = fxsloopstart set ring-frequency = ringfrequency20 set ring-back = off commit analog-fxs-cfg-profile 1/1/21/0/102 create analog-fxs-cfg-profile 1/1/22/0/102 set signal-type = fxsloopstart set ring-frequency = ringfrequency20 set ring-back = off commit analog-fxs-cfg-profile 1/1/22/0/102 create analog-fxs-cfg-profile 1/1/23/0/102 set signal-type = fxsloopstart set ring-frequency = ringfrequency20 set ring-back = off commit analog-fxs-cfg-profile 1/1/23/0/102 create analog-fxs-cfg-profile 1/1/24/0/102 set signal-type = fxsloopstart set ring-frequency = ringfrequency20 set ring-back = off commit analog-fxs-cfg-profile 1/1/24/0/102 create analog-if-cfg-profile 1/1/1/0/102 set if-cfg-impedence = ohms600real set if-cfg-receive-tlp = fxsrtlp0db set if-cfg-transmit-tlp = fxsttlp0db set if-cfg-trunk-conditioning = idle set if-maintenance-mode = off set if-cfg-pcm-encoding = mulaw commit analog-if-cfg-profile 1/1/1/0/102 create analog-if-cfg-profile 1/1/2/0/102 set if-cfg-impedence = ohms600real set if-cfg-receive-tlp = fxsrtlp0db set if-cfg-transmit-tlp = fxsttlp0db set if-cfg-trunk-conditioning = idle set if-maintenance-mode = off set if-cfg-pcm-encoding = mulaw commit analog-if-cfg-profile 1/1/2/0/102 create analog-if-cfg-profile 1/1/3/0/102 set if-cfg-impedence = ohms600real set if-cfg-receive-tlp = fxsrtlp0db set if-cfg-transmit-tlp = fxsttlp0db set if-cfg-trunk-conditioning = idle set if-maintenance-mode = off set if-cfg-pcm-encoding = mulaw commit analog-if-cfg-profile 1/1/3/0/102 create analog-if-cfg-profile 1/1/4/0/102 set if-cfg-impedence = ohms600real set if-cfg-receive-tlp = fxsrtlp0db set if-cfg-transmit-tlp = fxsttlp0db set if-cfg-trunk-conditioning = idle set if-maintenance-mode = off set if-cfg-pcm-encoding = mulaw commit analog-if-cfg-profile 1/1/4/0/102 create analog-if-cfg-profile 1/1/5/0/102 set if-cfg-impedence = ohms600real set if-cfg-receive-tlp = fxsrtlp0db set if-cfg-transmit-tlp = fxsttlp0db set if-cfg-trunk-conditioning = idle set if-maintenance-mode = off set if-cfg-pcm-encoding = mulaw commit analog-if-cfg-profile 1/1/5/0/102 create analog-if-cfg-profile 1/1/6/0/102 set if-cfg-impedence = ohms600real set if-cfg-receive-tlp = fxsrtlp0db set if-cfg-transmit-tlp = fxsttlp0db set if-cfg-trunk-conditioning = idle set if-maintenance-mode = off set if-cfg-pcm-encoding = mulaw commit analog-if-cfg-profile 1/1/6/0/102 create analog-if-cfg-profile 1/1/7/0/102 set if-cfg-impedence = ohms600real set if-cfg-receive-tlp = fxsrtlp0db set if-cfg-transmit-tlp = fxsttlp0db set if-cfg-trunk-conditioning = idle set if-maintenance-mode = off set if-cfg-pcm-encoding = mulaw commit analog-if-cfg-profile 1/1/7/0/102 create analog-if-cfg-profile 1/1/8/0/102 set if-cfg-impedence = ohms600real set if-cfg-receive-tlp = fxsrtlp0db set if-cfg-transmit-tlp = fxsttlp0db set if-cfg-trunk-conditioning = idle set if-maintenance-mode = off set if-cfg-pcm-encoding = mulaw commit analog-if-cfg-profile 1/1/8/0/102 create analog-if-cfg-profile 1/1/9/0/102 set if-cfg-impedence = ohms600real set if-cfg-receive-tlp = fxsrtlp0db set if-cfg-transmit-tlp = fxsttlp0db set if-cfg-trunk-conditioning = idle set if-maintenance-mode = off set if-cfg-pcm-encoding = mulaw commit analog-if-cfg-profile 1/1/9/0/102 create analog-if-cfg-profile 1/1/10/0/102 set if-cfg-impedence = ohms600real set if-cfg-receive-tlp = fxsrtlp0db set if-cfg-transmit-tlp = fxsttlp0db set if-cfg-trunk-conditioning = idle set if-maintenance-mode = off set if-cfg-pcm-encoding = mulaw commit analog-if-cfg-profile 1/1/10/0/102 create analog-if-cfg-profile 1/1/11/0/102 set if-cfg-impedence = ohms600real set if-cfg-receive-tlp = fxsrtlp0db set if-cfg-transmit-tlp = fxsttlp0db set if-cfg-trunk-conditioning = idle set if-maintenance-mode = off set if-cfg-pcm-encoding = mulaw commit analog-if-cfg-profile 1/1/11/0/102 create analog-if-cfg-profile 1/1/12/0/102 set if-cfg-impedence = ohms600real set if-cfg-receive-tlp = fxsrtlp0db set if-cfg-transmit-tlp = fxsttlp0db set if-cfg-trunk-conditioning = idle set if-maintenance-mode = off set if-cfg-pcm-encoding = mulaw commit analog-if-cfg-profile 1/1/12/0/102 create analog-if-cfg-profile 1/1/13/0/102 set if-cfg-impedence = ohms600real set if-cfg-receive-tlp = fxsrtlp0db set if-cfg-transmit-tlp = fxsttlp0db set if-cfg-trunk-conditioning = idle set if-maintenance-mode = off set if-cfg-pcm-encoding = mulaw commit analog-if-cfg-profile 1/1/13/0/102 create analog-if-cfg-profile 1/1/14/0/102 set if-cfg-impedence = ohms600real set if-cfg-receive-tlp = fxsrtlp0db set if-cfg-transmit-tlp = fxsttlp0db set if-cfg-trunk-conditioning = idle set if-maintenance-mode = off set if-cfg-pcm-encoding = mulaw commit analog-if-cfg-profile 1/1/14/0/102 create analog-if-cfg-profile 1/1/15/0/102 set if-cfg-impedence = ohms600real set if-cfg-receive-tlp = fxsrtlp0db set if-cfg-transmit-tlp = fxsttlp0db set if-cfg-trunk-conditioning = idle set if-maintenance-mode = off set if-cfg-pcm-encoding = mulaw commit analog-if-cfg-profile 1/1/15/0/102 create analog-if-cfg-profile 1/1/16/0/102 set if-cfg-impedence = ohms600real set if-cfg-receive-tlp = fxsrtlp0db set if-cfg-transmit-tlp = fxsttlp0db set if-cfg-trunk-conditioning = idle set if-maintenance-mode = off set if-cfg-pcm-encoding = mulaw commit analog-if-cfg-profile 1/1/16/0/102 create analog-if-cfg-profile 1/1/17/0/102 set if-cfg-impedence = ohms600real set if-cfg-receive-tlp = fxsrtlp0db set if-cfg-transmit-tlp = fxsttlp0db set if-cfg-trunk-conditioning = idle set if-maintenance-mode = off set if-cfg-pcm-encoding = mulaw commit analog-if-cfg-profile 1/1/17/0/102 create analog-if-cfg-profile 1/1/18/0/102 set if-cfg-impedence = ohms600real set if-cfg-receive-tlp = fxsrtlp0db set if-cfg-transmit-tlp = fxsttlp0db set if-cfg-trunk-conditioning = idle set if-maintenance-mode = off set if-cfg-pcm-encoding = mulaw commit analog-if-cfg-profile 1/1/18/0/102 create analog-if-cfg-profile 1/1/19/0/102 set if-cfg-impedence = ohms600real set if-cfg-receive-tlp = fxsrtlp0db set if-cfg-transmit-tlp = fxsttlp0db set if-cfg-trunk-conditioning = idle set if-maintenance-mode = off set if-cfg-pcm-encoding = mulaw commit analog-if-cfg-profile 1/1/19/0/102 create analog-if-cfg-profile 1/1/20/0/102 set if-cfg-impedence = ohms600real set if-cfg-receive-tlp = fxsrtlp0db set if-cfg-transmit-tlp = fxsttlp0db set if-cfg-trunk-conditioning = idle set if-maintenance-mode = off set if-cfg-pcm-encoding = mulaw commit analog-if-cfg-profile 1/1/20/0/102 create analog-if-cfg-profile 1/1/21/0/102 set if-cfg-impedence = ohms600real set if-cfg-receive-tlp = fxsrtlp0db set if-cfg-transmit-tlp = fxsttlp0db set if-cfg-trunk-conditioning = idle set if-maintenance-mode = off set if-cfg-pcm-encoding = mulaw commit analog-if-cfg-profile 1/1/21/0/102 create analog-if-cfg-profile 1/1/22/0/102 set if-cfg-impedence = ohms600real set if-cfg-receive-tlp = fxsrtlp0db set if-cfg-transmit-tlp = fxsttlp0db set if-cfg-trunk-conditioning = idle set if-maintenance-mode = off set if-cfg-pcm-encoding = mulaw commit analog-if-cfg-profile 1/1/22/0/102 create analog-if-cfg-profile 1/1/23/0/102 set if-cfg-impedence = ohms600real set if-cfg-receive-tlp = fxsrtlp0db set if-cfg-transmit-tlp = fxsttlp0db set if-cfg-trunk-conditioning = idle set if-maintenance-mode = off set if-cfg-pcm-encoding = mulaw commit analog-if-cfg-profile 1/1/23/0/102 create analog-if-cfg-profile 1/1/24/0/102 set if-cfg-impedence = ohms600real set if-cfg-receive-tlp = fxsrtlp0db set if-cfg-transmit-tlp = fxsttlp0db set if-cfg-trunk-conditioning = idle set if-maintenance-mode = off set if-cfg-pcm-encoding = mulaw commit analog-if-cfg-profile 1/1/24/0/102 create ds1 1/1/1/0/18 set line-type = esf set line-code = b8zs set send-code = sendnocode set circuit-id = ds1 set loopback-config = noloop set signal-mode = none set transmit-clock-source = looptiming set fdl = fdlnone set dsx-line-length = dsx0 set line-status-change-trap-enable = disabled set channelization = disabled set ds1-mode = csu set csu-line-length = csu00 set clock-source-eligible = eligible commit ds1 1/1/1/0/18 create ds1 1/1/2/0/18 set line-type = esf set line-code = b8zs set send-code = sendnocode set circuit-id = ds1 set loopback-config = noloop set signal-mode = none set transmit-clock-source = looptiming set fdl = fdlnone set dsx-line-length = dsx0 set line-status-change-trap-enable = disabled set channelization = disabled set ds1-mode = csu set csu-line-length = csu00 set clock-source-eligible = noteligible commit ds1 1/1/2/0/18 create ether 27 set autonegstatus = enabled set mauType = mau100basetxfd set restart = norestart set ifType = mau100basetxfd set autonegcap = b100baseTFD set remotefault = noerror commit ether 27 create if-default 0/126/6 set cardtype = 0 set upperiftype = ip set loweriftype = ethernetcsmacd set numunits = 1 set adminStatus = up commit if-default 0/126/6 create if-default 0/6/0 set cardtype = 0 set upperiftype = ethernetcsmacd set loweriftype = NONE(0) set numunits = 1 set adminStatus = up commit if-default 0/6/0 create if-default 0/126/159 set cardtype = 0 set upperiftype = ip set loweriftype = rfc1483 set numunits = 1 set adminStatus = up commit if-default 0/126/159 create if-default 0/159/49 set cardtype = 0 set upperiftype = rfc1483 set loweriftype = aal5 set numunits = 1 set adminStatus = up commit if-default 0/159/49 create if-default 0/49/168 set cardtype = 0 set upperiftype = aal5 set loweriftype = hdsl2 set numunits = 1 set adminStatus = up commit if-default 0/49/168 create if-default 0/168/0 set cardtype = 0 set upperiftype = hdsl2 set loweriftype = NONE(0) set numunits = 1 set adminStatus = up commit if-default 0/168/0 create if-default 0/37/0 set cardtype = 0 set upperiftype = atm set loweriftype = NONE(0) set numunits = 1 set adminStatus = up commit if-default 0/37/0 create if-next-index 1/1/1/0/18 set nextifindex = 34 commit if-next-index 1/1/1/0/18 create if-stack 28/27 set upperlayer = 28 set lowerlayer = 27 commit if-stack 28/27 create ip-interface-record 1/1/1/0/126 set lgid = 0 set vpi = 0 set vci = 0 set rdindex = 0 set dhcp = none set addr = 192.168.1.250 set netmask = 255.255.255.0 set bcastaddr = 0.0.0.0 set destaddr = 0.0.0.0 set farendaddr = 0.0.0.0 set mru = 0 set reasmmaxsize = 0 set ingressfiltername = "" set egressfiltername = "" set pointtopoint = no set mcastenabled = yes set ipfwdenabled = yes set mcastfwdenabled = yes set natenabled = no set bcastenabled = yes commit ip-interface-record 1/1/1/0/126 create line-group 1 set group-id = 1 set group-name = "" set primary-name = 1 set primary-weight = 0 set secondary-name = 0 set secondary-weight = 0 set admin-state = up commit line-group 1 create line-group 2 set group-id = 2 set group-name = "" set primary-name = 2 set primary-weight = 0 set secondary-name = 0 set secondary-weight = 0 set admin-state = down commit line-group 2 create line-group 3 set group-id = 3 set group-name = "" set primary-name = 3 set primary-weight = 0 set secondary-name = 0 set secondary-weight = 0 set admin-state = up commit line-group 3 create line-group 4 set group-id = 4 set group-name = "" set primary-name = 4 set primary-weight = 0 set secondary-name = 0 set secondary-weight = 0 set admin-state = up commit line-group 4 create line-group 5 set group-id = 5 set group-name = "" set primary-name = 5 set primary-weight = 0 set secondary-name = 0 set secondary-weight = 0 set admin-state = up commit line-group 5 create line-group 6 set group-id = 6 set group-name = "" set primary-name = 6 set primary-weight = 0 set secondary-name = 0 set secondary-weight = 0 set admin-state = up commit line-group 6 create line-group 7 set group-id = 7 set group-name = "" set primary-name = 7 set primary-weight = 0 set secondary-name = 0 set secondary-weight = 0 set admin-state = up commit line-group 7 create line-group 8 set group-id = 8 set group-name = "" set primary-name = 8 set primary-weight = 0 set secondary-name = 0 set secondary-weight = 0 set admin-state = up commit line-group 8 create line-group 9 set group-id = 9 set group-name = "" set primary-name = 9 set primary-weight = 0 set secondary-name = 0 set secondary-weight = 0 set admin-state = up commit line-group 9 create line-group 10 set group-id = 10 set group-name = "" set primary-name = 10 set primary-weight = 0 set secondary-name = 0 set secondary-weight = 0 set admin-state = up commit line-group 10 create line-group 11 set group-id = 11 set group-name = "" set primary-name = 11 set primary-weight = 0 set secondary-name = 0 set secondary-weight = 0 set admin-state = up commit line-group 11 create line-group 12 set group-id = 12 set group-name = "" set primary-name = 12 set primary-weight = 0 set secondary-name = 0 set secondary-weight = 0 set admin-state = up commit line-group 12 create line-group 13 set group-id = 13 set group-name = "" set primary-name = 13 set primary-weight = 0 set secondary-name = 0 set secondary-weight = 0 set admin-state = up commit line-group 13 create line-group 14 set group-id = 14 set group-name = "" set primary-name = 14 set primary-weight = 0 set secondary-name = 0 set secondary-weight = 0 set admin-state = up commit line-group 14 create line-group 15 set group-id = 15 set group-name = "" set primary-name = 15 set primary-weight = 0 set secondary-name = 0 set secondary-weight = 0 set admin-state = up commit line-group 15 create line-group 16 set group-id = 16 set group-name = "" set primary-name = 16 set primary-weight = 0 set secondary-name = 0 set secondary-weight = 0 set admin-state = up commit line-group 16 create line-group 17 set group-id = 17 set group-name = "" set primary-name = 17 set primary-weight = 0 set secondary-name = 0 set secondary-weight = 0 set admin-state = up commit line-group 17 create line-group 18 set group-id = 18 set group-name = "" set primary-name = 18 set primary-weight = 0 set secondary-name = 0 set secondary-weight = 0 set admin-state = up commit line-group 18 create line-group 19 set group-id = 19 set group-name = "" set primary-name = 19 set primary-weight = 0 set secondary-name = 0 set secondary-weight = 0 set admin-state = up commit line-group 19 create line-group 20 set group-id = 20 set group-name = "" set primary-name = 20 set primary-weight = 0 set secondary-name = 0 set secondary-weight = 0 set admin-state = up commit line-group 20 create line-group 21 set group-id = 21 set group-name = "" set primary-name = 21 set primary-weight = 0 set secondary-name = 0 set secondary-weight = 0 set admin-state = up commit line-group 21 create line-group 22 set group-id = 22 set group-name = "" set primary-name = 22 set primary-weight = 0 set secondary-name = 0 set secondary-weight = 0 set admin-state = up commit line-group 22 create line-group 23 set group-id = 23 set group-name = "" set primary-name = 23 set primary-weight = 0 set secondary-name = 0 set secondary-weight = 0 set admin-state = up commit line-group 23 create line-group 24 set group-id = 24 set group-name = "" set primary-name = 24 set primary-weight = 0 set secondary-name = 0 set secondary-weight = 0 set admin-state = up commit line-group 24 create line-group 25 set group-id = 25 set group-name = "" set primary-name = 25 set primary-weight = 0 set secondary-name = 0 set secondary-weight = 0 set admin-state = up commit line-group 25 create line-group 26 set group-id = 26 set group-name = "" set primary-name = 26 set primary-weight = 0 set secondary-name = 0 set secondary-weight = 0 set admin-state = up commit line-group 26 create line-group 27 set group-id = 27 set group-name = "" set primary-name = 27 set primary-weight = 0 set secondary-name = 0 set secondary-weight = 0 set admin-state = up commit line-group 27 create line-profile 1/1/1/0/18 set profile-name = "Ds1 default line profile" set shelf = 1 set slot = 1 set port = 1 set subPort = 0 set line-group-name = 1 commit line-profile 1/1/1/0/18 create line-profile 1/1/2/0/18 set profile-name = "Ds1 default line profile" set shelf = 1 set slot = 1 set port = 2 set subPort = 0 set line-group-name = 2 commit line-profile 1/1/2/0/18 create line-profile 1/1/1/0/102 set profile-name = "default line profile " set shelf = 1 set slot = 1 set port = 1 set subPort = 0 set line-group-name = 3 commit line-profile 1/1/1/0/102 create line-profile 1/1/2/0/102 set profile-name = "default line profile " set shelf = 1 set slot = 1 set port = 2 set subPort = 0 set line-group-name = 4 commit line-profile 1/1/2/0/102 create line-profile 1/1/3/0/102 set profile-name = "default line profile " set shelf = 1 set slot = 1 set port = 3 set subPort = 0 set line-group-name = 5 commit line-profile 1/1/3/0/102 create line-profile 1/1/4/0/102 set profile-name = "default line profile " set shelf = 1 set slot = 1 set port = 4 set subPort = 0 set line-group-name = 6 commit line-profile 1/1/4/0/102 create line-profile 1/1/5/0/102 set profile-name = "default line profile " set shelf = 1 set slot = 1 set port = 5 set subPort = 0 set line-group-name = 7 commit line-profile 1/1/5/0/102 create line-profile 1/1/6/0/102 set profile-name = "default line profile " set shelf = 1 set slot = 1 set port = 6 set subPort = 0 set line-group-name = 8 commit line-profile 1/1/6/0/102 create line-profile 1/1/7/0/102 set profile-name = "default line profile " set shelf = 1 set slot = 1 set port = 7 set subPort = 0 set line-group-name = 9 commit line-profile 1/1/7/0/102 create line-profile 1/1/8/0/102 set profile-name = "default line profile " set shelf = 1 set slot = 1 set port = 8 set subPort = 0 set line-group-name = 10 commit line-profile 1/1/8/0/102 create line-profile 1/1/9/0/102 set profile-name = "default line profile " set shelf = 1 set slot = 1 set port = 9 set subPort = 0 set line-group-name = 11 commit line-profile 1/1/9/0/102 create line-profile 1/1/10/0/102 set profile-name = "default line profile " set shelf = 1 set slot = 1 set port = 10 set subPort = 0 set line-group-name = 12 commit line-profile 1/1/10/0/102 create line-profile 1/1/11/0/102 set profile-name = "default line profile " set shelf = 1 set slot = 1 set port = 11 set subPort = 0 set line-group-name = 13 commit line-profile 1/1/11/0/102 create line-profile 1/1/12/0/102 set profile-name = "default line profile " set shelf = 1 set slot = 1 set port = 12 set subPort = 0 set line-group-name = 14 commit line-profile 1/1/12/0/102 create line-profile 1/1/13/0/102 set profile-name = "default line profile " set shelf = 1 set slot = 1 set port = 13 set subPort = 0 set line-group-name = 15 commit line-profile 1/1/13/0/102 create line-profile 1/1/14/0/102 set profile-name = "default line profile " set shelf = 1 set slot = 1 set port = 14 set subPort = 0 set line-group-name = 16 commit line-profile 1/1/14/0/102 create line-profile 1/1/15/0/102 set profile-name = "default line profile " set shelf = 1 set slot = 1 set port = 15 set subPort = 0 set line-group-name = 17 commit line-profile 1/1/15/0/102 create line-profile 1/1/16/0/102 set profile-name = "default line profile " set shelf = 1 set slot = 1 set port = 16 set subPort = 0 set line-group-name = 18 commit line-profile 1/1/16/0/102 create line-profile 1/1/17/0/102 set profile-name = "default line profile " set shelf = 1 set slot = 1 set port = 17 set subPort = 0 set line-group-name = 19 commit line-profile 1/1/17/0/102 create line-profile 1/1/18/0/102 set profile-name = "default line profile " set shelf = 1 set slot = 1 set port = 18 set subPort = 0 set line-group-name = 20 commit line-profile 1/1/18/0/102 create line-profile 1/1/19/0/102 set profile-name = "default line profile " set shelf = 1 set slot = 1 set port = 19 set subPort = 0 set line-group-name = 21 commit line-profile 1/1/19/0/102 create line-profile 1/1/20/0/102 set profile-name = "default line profile " set shelf = 1 set slot = 1 set port = 20 set subPort = 0 set line-group-name = 22 commit line-profile 1/1/20/0/102 create line-profile 1/1/21/0/102 set profile-name = "default line profile " set shelf = 1 set slot = 1 set port = 21 set subPort = 0 set line-group-name = 23 commit line-profile 1/1/21/0/102 create line-profile 1/1/22/0/102 set profile-name = "default line profile " set shelf = 1 set slot = 1 set port = 22 set subPort = 0 set line-group-name = 24 commit line-profile 1/1/22/0/102 create line-profile 1/1/23/0/102 set profile-name = "default line profile " set shelf = 1 set slot = 1 set port = 23 set subPort = 0 set line-group-name = 25 commit line-profile 1/1/23/0/102 create line-profile 1/1/24/0/102 set profile-name = "default line profile " set shelf = 1 set slot = 1 set port = 24 set subPort = 0 set line-group-name = 26 commit line-profile 1/1/24/0/102 create line-profile 1/1/1/0/6 set profile-name = "default line profile" set shelf = 1 set slot = 1 set port = 1 set subPort = 0 set line-group-name = 27 commit line-profile 1/1/1/0/6 create physical-to-ifindex 1/1/1/0 set ifindex = 27 commit physical-to-ifindex 1/1/1/0 create rip-if-config 0/192/168/1/250 set auth-type = none set auth-key = "" set send-type = donotsend set receive-type = donotreceive set default-metric = 0 set src-address = -1062731270 set sroute-advertise = none set poison = disabled commit rip-if-config 0/192/168/1/250 create system 0 set syscontact = "" set sysname = "" set syslocation = "" set enableauthtraps = NONE(0) set setserialno = 0 set zmsexists = false set zmsconnectionstatus = inactive set zmsipaddress = 0.0.0.0 set configsyncexists = NONE(0) set configsyncoverflow = NONE(0) set configsyncpriority = low set configsyncaction = NONE(0) set configsyncfilename = "" set configsyncstatus = NONE(0) set configsyncuser = "" set configsyncpasswd = "" set numshelves = 0 set shelvesarray = "" set numcards = 0 set ipaddress = 0.0.0.0 set alternateipaddress = 0.0.0.0 commit system 0 create tdm-xcon 1/1 set xcon-type = voice set xcon-to-port-group-id = 3 set xcon-to-TS = 0 set xcon-highway = na commit tdm-xcon 1/1 create tdm-xcon 1/2 set xcon-type = voice set xcon-to-port-group-id = 4 set xcon-to-TS = 0 set xcon-highway = na commit tdm-xcon 1/2 create tdm-xcon 1/3 set xcon-type = voice set xcon-to-port-group-id = 5 set xcon-to-TS = 0 set xcon-highway = na commit tdm-xcon 1/3 create tdm-xcon 1/4 set xcon-type = voice set xcon-to-port-group-id = 6 set xcon-to-TS = 0 set xcon-highway = na commit tdm-xcon 1/4 create tdm-xcon 1/5 set xcon-type = voice set xcon-to-port-group-id = 7 set xcon-to-TS = 0 set xcon-highway = na commit tdm-xcon 1/5 create tdm-xcon 1/6 set xcon-type = voice set xcon-to-port-group-id = 8 set xcon-to-TS = 0 set xcon-highway = na commit tdm-xcon 1/6 create tdm-xcon 1/7 set xcon-type = voice set xcon-to-port-group-id = 9 set xcon-to-TS = 0 set xcon-highway = na commit tdm-xcon 1/7 create tdm-xcon 1/8 set xcon-type = voice set xcon-to-port-group-id = 10 set xcon-to-TS = 0 set xcon-highway = na commit tdm-xcon 1/8 create tdm-xcon 1/9 set xcon-type = voice set xcon-to-port-group-id = 11 set xcon-to-TS = 0 set xcon-highway = na commit tdm-xcon 1/9 create tdm-xcon 1/10 set xcon-type = voice set xcon-to-port-group-id = 12 set xcon-to-TS = 0 set xcon-highway = na commit tdm-xcon 1/10 create tdm-xcon 1/11 set xcon-type = voice set xcon-to-port-group-id = 13 set xcon-to-TS = 0 set xcon-highway = na commit tdm-xcon 1/11 create tdm-xcon 1/12 set xcon-type = voice set xcon-to-port-group-id = 14 set xcon-to-TS = 0 set xcon-highway = na commit tdm-xcon 1/12 create tdm-xcon 1/13 set xcon-type = voice set xcon-to-port-group-id = 15 set xcon-to-TS = 0 set xcon-highway = na commit tdm-xcon 1/13 create tdm-xcon 1/14 set xcon-type = voice set xcon-to-port-group-id = 16 set xcon-to-TS = 0 set xcon-highway = na commit tdm-xcon 1/14 create tdm-xcon 1/15 set xcon-type = voice set xcon-to-port-group-id = 17 set xcon-to-TS = 0 set xcon-highway = na commit tdm-xcon 1/15 create tdm-xcon 1/16 set xcon-type = voice set xcon-to-port-group-id = 18 set xcon-to-TS = 0 set xcon-highway = na commit tdm-xcon 1/16 create tdm-xcon 1/17 set xcon-type = voice set xcon-to-port-group-id = 19 set xcon-to-TS = 0 set xcon-highway = na commit tdm-xcon 1/17 create tdm-xcon 1/18 set xcon-type = voice set xcon-to-port-group-id = 20 set xcon-to-TS = 0 set xcon-highway = na commit tdm-xcon 1/18 create tdm-xcon 1/19 set xcon-type = voice set xcon-to-port-group-id = 21 set xcon-to-TS = 0 set xcon-highway = na commit tdm-xcon 1/19 create tdm-xcon 1/20 set xcon-type = voice set xcon-to-port-group-id = 22 set xcon-to-TS = 0 set xcon-highway = na commit tdm-xcon 1/20 create tdm-xcon 1/21 set xcon-type = voice set xcon-to-port-group-id = 23 set xcon-to-TS = 0 set xcon-highway = na commit tdm-xcon 1/21 create tdm-xcon 1/22 set xcon-type = voice set xcon-to-port-group-id = 24 set xcon-to-TS = 0 set xcon-highway = na commit tdm-xcon 1/22 create tdm-xcon 1/23 set xcon-type = voice set xcon-to-port-group-id = 25 set xcon-to-TS = 0 set xcon-highway = na commit tdm-xcon 1/23 create tdm-xcon 1/24 set xcon-type = voice set xcon-to-port-group-id = 26 set xcon-to-TS = 0 set xcon-highway = na commit tdm-xcon 1/24 create user-profile 0 set user-id = 0 set user-name = USER_SEED_REC set user-pass = NOT_A_USER set user-prompt = 10 set admin-access = 0 set debug-access = 0 set voice-access = 0 set data-access = 0 set manuf-access = 0 set database-access = 0 set system-access = 0 set tools-access = 0 set user-admin-access = 0 set zhone-access = 0 commit user-profile 0 create user-profile 1 set user-id = 1 set user-name = zhonedevel set user-pass = zeebbSdSd set user-prompt = zSH> set admin-access = 1 set debug-access = 1 set voice-access = 1 set data-access = 1 set manuf-access = 1 set database-access = 1 set system-access = 1 set tools-access = 1 set user-admin-access = 1 set zhone-access = 1 commit user-profile 1 create user-profile 2 set user-id = 2 set user-name = admin set user-pass = Sedyzybceb set user-prompt = zSH> set admin-access = 1 set debug-access = 0 set voice-access = 1 set data-access = 1 set manuf-access = 1 set database-access = 1 set system-access = 1 set tools-access = 1 set user-admin-access = 1 set zhone-access = 0 commit user-profile 2
