did you see the message from the person who commented on all of your errors
on eth1.
i think they might be on to something as far as eth1 not having the correct
driver?
remember i am no expert and am just fumbling along with you.
i will call your machine with redhat7 and 2 network cards the router.
can you ping eth1 from the router machine?
can you ping eth1 from one of the client machines?
can you ping eth0 from one of the client machines?
can you ping an address on the internet from the router machine?
209.1.8.14 will return a ping for me (sco.com)
on a side note, you're sure your not plugged into an uplink port on your
hub?
----- Original Message -----
From: "Adahma" <[EMAIL PROTECTED]>
To: <[EMAIL PROTECTED]>
Sent: Friday, February 09, 2001 8:33 PM
Subject: Re: Routing problems (home network setup)
> On Fri, Feb 09, 2001 at 02:03:24PM -0600, Mikkel L. Ellertson wrote:
> > Do the computers on your internel network have routable IP addresses, or
> > are you using one of the private IP ranges for your internel network?
> > Unless you are getting extra IP address from your cable company, you
> > should be doing the later. If so, you should read the IP-Masquerade
> > HOWTO. I would also recomend the IPCHAINS-HOWTO.
>
> I have essentially the same problem, and have spent considerable
> time trying to get it to work with no success.
>
> I have a cable modem connected to my Red Hat 7 box on eth0, and eth1
> connecting to a 5 port hub which I'd like to setup on the 192.168
> private ip's and do masqerading for. Here's my applicable files:
>
> [ifcfg-eth0]
>
> DEVICE="eth0"
> BOOTPROTO="none"
> BROADCAST=24.14.246.127
> IPADDR="24.14.246.95"
> NETMASK="255.255.255.128"
> NETWORK=24.14.246.0
> ONBOOT="yes"
> IPXNETNUM_802_2=""
> IPXPRIMARY_802_2="no"
> IPXACTIVE_802_2="no"
> IPXNETNUM_802_3=""
> IPXPRIMARY_802_3="no"
> IPXACTIVE_802_3="no"
> IPXNETNUM_ETHERII=""
> IPXPRIMARY_ETHERII="no"
> IPXACTIVE_ETHERII="no"
> IPXNETNUM_SNAP=""
> IPXPRIMARY_SNAP="no"
> IPXACTIVE_SNAP="no"
>
> [ifcfg-eth1]
>
> DEVICE="eth1"
> ONBOOT="yes"
> BOOTPROTO="none"
> IPADDR="192.168.1.1"
> NETMASK="255.255.255.0"
> NETWORK="192.168.1.0"
>
> I do have masqerading rules running for the ipchains setup I'm
> running. I've setup the 2 client machines as 192.168.1.101 and
> 192.168.1.102, and have both pointing to eth1(192.168.1.1) as their
> gateway, and my cable providers DNS servers. Can anyone tell me
> what my flaw is? The 2 machines have no luck talking to the
> internet connected this way. Are there some route commands needed
> here or something? I do show lots of errors on eth1 on an ifconfig:
>
> eth0 Link encap:Ethernet HWaddr 00:50:BA:04:73:79
> inet addr:24.14.246.95 Bcast:24.14.246.127
Mask:255.255.255.128
> UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
> RX packets:6068 errors:0 dropped:0 overruns:0 frame:0
> TX packets:5573 errors:0 dropped:0 overruns:0 carrier:0
> collisions:0 txqueuelen:100
> Interrupt:11 Base address:0xe400
>
> eth1 Link encap:Ethernet HWaddr 00:A0:CC:E8:2A:BD
> inet addr:192.168.1.1 Bcast:192.168.1.255 Mask:255.255.255.0
> UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
> RX packets:0 errors:1068 dropped:0 overruns:0 frame:0
> TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
> collisions:0 txqueuelen:100
> Interrupt:10 Base address:0xe800
>
> lo Link encap:Local Loopback
> inet addr:127.0.0.1 Mask:255.0.0.0
> UP LOOPBACK RUNNING MTU:16128 Metric:1
> RX packets:1721 errors:0 dropped:0 overruns:0 frame:0
> TX packets:1721 errors:0 dropped:0 overruns:0 carrier:0
> collisions:0 txqueuelen:0
>
> Any and all help is greatly appreciated!!
>
> TIA,
> jdk
>
>
>
> _______________________________________________
> Redhat-list mailing list
> [EMAIL PROTECTED]
> https://listman.redhat.com/mailman/listinfo/redhat-list
>
_______________________________________________
Redhat-list mailing list
[EMAIL PROTECTED]
https://listman.redhat.com/mailman/listinfo/redhat-list
