Here is output from the uboot process. It never gets to the part where
it's handed over to openbsd. Note that this is after installation from sdmmc
the sdmmc card removed and the machine turned on with the usb3 ssd plugged in.
1.67 RPi: BOOTSYS release VERSION:85353ce4 DATE: 2026/02/23 TIME: 10:01:39
1.67 BOOTMODE: 0x06 partition 0 build-ts BUILD_TIMESTAMP=1771840899 serial
1af94b12 boardrev e04171 stc 1675632
1.68 AON_RESET: 00000003 PM_RSTS 00001000
1.68 POWER_OFF_ON_HALT: 0 WAIT_FOR_POWER_BUTTON 0 power-on-reset 1
1.69 RP1_BOOT chip ID: 0x20001927
1.70 PCIEx1: PWR 0 DET_WAKE 0
1.70 part 00000000 reset_info 00000000
1.70 PMIC reset-event 00000000 rtc 00000001 alarm 00000000 enabled 0
1.71 uSD voltage 3.3V
1.71 SDRAM_CONFIG: 1b
1.71 Initialising SDRAM rank 2 total-size: 128Gbit 0 part: 0 (0x1b 0x1b)
1.72 memsys_init: 0 128Gbit MCB 0x80015ff0: 5488
1.73 DDR 4267 Mbps dual-rank:1 byte-mode:1 size-gbit:128
2.37 RP1 FW: load 0
2.38 RP1_BOOT chip ID: 0x20001927
3.53 RP1 FW: load 1
3.96 OTP boardrev e04171 bootrom a a
3.96 Customer key hash
0000000000000000000000000000000000000000000000000000000000000000
3.97 VC-JTAG unlocked
3.99 RP1_BOOT chip ID: 0x20001927
4.63 PCI2 init
4.65 PCI2 reset
4.70 PCIe scan 00001de4:00000001
4.70 RP1_CHIP_INFO 20001927
4.70 RPi: BOOTLOADER release VERSION:85353ce4 DATE: 2026/02/23 TIME: 10:01:39
4.71 BOOTMODE: 0x06 partition 0 build-ts BUILD_TIMESTAMP=1771840899 serial
1af94b12 boardrev e04171 stc 4711873
4.72 PCIEx1: PWR 0 DET_WAKE 0
4.24 M.2 PCIe HAT not detected.
4.73 usb_pd_init status 3
4.73 USB_PD CONFIG 0 41
4.80 XHCI-STOP
4.80 xHC0 ver: 272 HCS: 03000440 140000f1 07ff000a HCC: 0240fe6d
4.80 USBSTS 1
4.81 xHC0 ver: 272 HCS: 03000440 140000f1 07ff000a HCC: 0240fe6d
4.81 xHC0 ports 3 slots 64 intrs 4
4.83 XHCI-STOP
4.83 xHC1 ver: 272 HCS: 03000440 140000f1 07ff000a HCC: 0240fe6d
4.84 USBSTS 1
4.84 xHC1 ver: 272 HCS: 03000440 140000f1 07ff000a HCC: 0240fe6d
4.84 xHC1 ports 3 slots 64 intrs 4
4.85 USB-PD: src-cap PDO object1 0x0a0191f4
4.85 Current 5000 mA
4.85 Voltage 5000 mV
4.86 USB-PD: src-cap PDO object2 0x0002d12c
4.86 Current 3000 mA
4.86 Voltage 9000 mV
4.86 USB-PD: src-cap PDO object3 0x0003c0e1
4.87 Current 2250 mA
4.87 Voltage 12000 mV
4.87 USB-PD: src-cap PDO object4 0x0004b0b4
4.88 Current 1800 mA
4.88 Voltage 15000 mV
4.92 SD_OC: 0
4.25 Boot mode: USB-MSD (04) order f1
5.63 USB2[2] 00020ae1 connected
5.13 USB2[2] 00200a03 connected enabled
5.14 USB2 root HUB port 2 init
5.27 DEV [01:00] 1.16 000000:02 class 0 VID 1a2c PID 4b61
5.90 HID [01:00] 1.16 000000:02 register HID
5.53 USB3[3] 00021203 connected enabled
5.54 USB3 root HUB port 3 init
5.55 DEV [02:00] 3.32 000000:03 class 0 VID 0951 PID 1780
5.56 MSD device [02:00] 3.32 000000:03 conf 0 iface 0 ep 82#1024 01#1024
5.69 MSD [02:00] 3.32 000000:03 register MSD
9.57 XHCI-STOP
9.57 xHC0 ver: 272 HCS: 03000440 140000f1 07ff000a HCC: 0240fe6d
9.57 USBSTS 0
9.58 XHCI-STOP
9.58 xHC1 ver: 272 HCS: 03000440 140000f1 07ff000a HCC: 0240fe6d
9.58 USBSTS 18
9.59 XHCI-STOP
9.59 xHC0 ver: 272 HCS: 03000440 140000f1 07ff000a HCC: 0240fe6d
9.59 USBSTS 1
9.60 xHC0 ver: 272 HCS: 03000440 140000f1 07ff000a HCC: 0240fe6d
9.60 xHC0 ports 3 slots 64 intrs 4
9.61 XHCI-STOP
9.61 xHC1 ver: 272 HCS: 03000440 140000f1 07ff000a HCC: 0240fe6d
9.62 USBSTS 19
9.62 xHC1 ver: 272 HCS: 03000440 140000f1 07ff000a HCC: 0240fe6d
9.62 xHC1 ports 3 slots 64 intrs 4
9.87 USB2[2] 00020ae1 connected
9.38 USB2[2] 00200a03 connected enabled
9.38 USB2 root HUB port 2 init
9.41 USB3[3] 002a1203 connected enabled
9.76 DEV [01:00] 1.16 000000:02 class 0 VID 1a2c PID 4b61
9.76 HID [01:00] 1.16 000000:02 register HID
9.37 USB3 root HUB port 3 init
9.88 DEV [02:00] 3.32 000000:03 class 0 VID 0951 PID 1780
9.89 MSD device [02:00] 3.32 000000:03 conf 0 iface 0 ep 82#1024 01#1024
9.98 MSD [02:00] 3.32 000000:03 register MSD
9.02 MSD [02:00] 3.32 000000:03 LUN 0
9.11 MSD READ_CAPACITY [02:00] 3.32 000000:03 lun 0 block-count 3907029168
block-size 512
9.91 MBR: 0x00008000, 32768 type: 0x0c
9.92 MBR: 0x00000000, 0 type: 0x00
9.92 MBR: 0x00000000, 0 type: 0x00
9.92 MBR: 0x00010000,3906963632 type: 0xa6
9.32 Trying partition: 0
9.34 type: 16 lba: 32768 'BSD 4.4' ' ^ ' clusters 8167 (4)
9.94 rsc 1 fat-sectors 32 root dir cluster 1 sectors 32 entries 512
9.94 FAT16 clusters 8167
9.95 [MSD [02:00] 3.32 000000:03] autoboot.txt not found
9.95 Select partition rsts 0 C(boot_partition) 0 EEPROM config 0 result 1
9.61 Trying partition: 1
9.64 type: 16 lba: 32768 'BSD 4.4' ' ^ ' clusters 8167 (4)
9.97 rsc 1 fat-sectors 32 root dir cluster 1 sectors 32 entries 512
9.97 FAT16 clusters 8167
9.80 Read config.txt bytes 65 hnd 0x28f
9.98 [MSD [02:00] 3.32 000000:03] pieeprom.upd not found
9.88 usb_max_current_enable default 0 max-current 5000
9.95 Read bcm2712-rpi-5-b.dtb bytes 78231 hnd 0x164
9.99 dt-match: compatible: raspberrypi,5-model-b match: brcm,bcm2712
10.00 dt-match: compatible: brcm,bcm2712 match: brcm,bcm2712
10.02 MESS:00:00:10.022474:0: *** Restart logging
10.24 Read /config.txt bytes 65 hnd 0x28f
10.02 MESS:00:00:10.029078:0: board: boardrev e04171 otp e04171
10.34 Read /config.txt bytes 65 hnd 0x28f
10.09 MESS:00:00:10.094092:0: Initial voltage 800000 temp 26289
10.29 MESS:00:00:10.294506:0: avs_2712: AVS pred 8807 880700 temp 26289
10.29 MESS:00:00:10.298109:0: vpred 880 mV +0
10.30 MESS:00:00:10.302316:0: over-voltage idle: 0 avs: 120700 delta: 0
(0x00000000)
10.31 MESS:00:00:10.314448:0: FB framebuffer_swap 1
10.31 MESS:00:00:10.316314:0: Select resolution HDMI0/2 hotplug 0 max_mode 2
10.32 MESS:00:00:10.323203:0: Select resolution HDMI1/2 hotplug 0 max_mode 2
10.33 MESS:00:00:10.330685:0: dtb_file 'bcm2712-rpi-5-b.dtb'
10.33 Loading 'bcm2712-rpi-5-b.dtb' to 0x00000000 offset 0x100
10.42 Read bcm2712-rpi-5-b.dtb bytes 78231 hnd 0x164
10.36 [MSD [02:00] 3.32 000000:03] /overlays/overlay_map.dtb not found
10.70 /overlays/overlay_map.dtb
10.74 Read /overlays/bcm2712d0.dtbo bytes 1363 hnd 0x1e76
10.39 MESS:00:00:10.399129:0: Loaded overlay 'bcm2712d0'
10.47 PCIEx1: PWR 0 DET_WAKE 0
10.83 Read /config.txt bytes 65 hnd 0x28f
10.85 Read /overlays/disable-bt.dtbo bytes 1073 hnd 0xfe6
10.50 MESS:00:00:10.503625:0: dterror: can't find symbol 'bt'
10.50 MESS:00:00:10.506366:0: dterror: Failed to resolve overlay 'disable-bt'
10.57 [MSD [02:00] 3.32 000000:03] /cmdline.txt not found
10.79 /cmdline.txt
10.58 MESS:00:00:10.581773:0: Failed to open command line file 'cmdline.txt'
10.76 MESS:00:00:10.765781:0: RPM 106, max RPM 322
10.82 BMD "armstub8-2712.bin" not found
10.27 fs_open: 'armstub8-2712.bin'
10.83 Loading 'u-boot.bin' to 0x00000000 offset 0x200000
10.40 Read u-boot.bin bytes 697712 hnd 0xd41
10.84 MESS:00:00:10.842764:0: Kernel relocated to 0x80000
10.84 MESS:00:00:10.847606:0: Device tree loaded to 0x2efec600 (size 0x1393b)
10.85 PCI1 reset
10.86 PCI2 reset
10.87 set_reboot_order 0
10.87 set_reboot_arg1 0
10.87 USB-OTG disconnect
10.91 MESS:00:00:10.919918:0: BSC_A no ACK
10.92 MESS:00:00:10.921153:0: BSC_A no ACK
10.92 MESS:00:00:10.925078:0: BSC_A no ACK
10.94 MESS:00:00:10.949007:0: BSC_B no ACK
10.95 MESS:00:00:10.950234:0: BSC_B no ACK
10.95 MESS:00:00:10.954169:0: BSC_B no ACK
10.97 MESS:00:00:10.977940:0: Starting OS 10977 ms
10.98 MESS:00:00:10.983551:0: 00000040: -> 00000480
10.98 MESS:00:00:10.985405:0: 00000030: -> 00100080
10.99 MESS:00:00:10.990118:0: 00000034: -> 00100080
10.99 MESS:00:00:10.994830:0: 00000038: -> 00100080
10.99 MESS:00:00:10.999544:0: 0000003c: -> 00100080
NOTICE: BL31: v2.6(release):v2.6-240-gfc45bc492
NOTICE: BL31: Built : 12:55:13, Dec 4 2024
U-Boot 2025.07 (Mar 02 2026 - 10:13:27 -0700)
DRAM: 1020 MiB (total 16 GiB)
RPI 5 Model B (0xe04171)
Core: 25 devices, 11 uclasses, devicetree: board
MMC: mmc@fff000: 0, mmc@1100000: 1
Loading Environment from FAT... Card did not respond to voltage select! : -110
** Bad device specification mmc 0 **
In: serial,usbkbd
Out: serial,vidconsole
Err: serial,vidconsole
Net: No ethernet found.
starting USB...
No USB controllers found
scanning usb for storage devices... 0 Storage Device(s) found
Hit any key to stop autoboot: 0
Card did not respond to voltage select! : -110
Cannot persist EFI variables without system partition
Card did not respond to voltage select! : -110
U-Boot> boot
Card did not respond to voltage select! : -110
U-Boot> setenv bootdelay -2
U-Boot> saveenv
Saving Environment to FAT... Card did not respond to voltage select! : -110
** Bad device specification mmc 0 **
Failed (1)
U-Boot> boot
Card did not respond to voltage select! : -110
U-Boot>
