On Saturday, April 11th, 2026 at 11:24 AM, Ampie Niemand <[email protected]>
wrote:
> Have you tried this advice from the INSTALL.arm64 instructions:
>
> "Alternatively the system can be booted using UEFI firmware found at
> https://github.com/pftf/RPi4. Follow their instructions to install to
> an
> SD card and run the OpenBSD installer from USB. v1.21 is known to
> work;
> some newer versions may have problems."
Ampie,
I tried using the UEFI firmware, both the most recent version and the v1.21,
both to a similar effect. Attached are the script files for each attempt. It
seems that the ethernet over bse0 is still not working (neither dig nor pinging
9.9.9.9 succeeds), and on v1.21 it seems to hang on disk formatting, which was
not happening when I booted the miniroot directly from the sd card. Version
1.51 gives the error:
IPv4 address for bse0? (or 'autoconf' or 'none') [autoconf]
No dhcp address on interface bse0 in 30 seconds.
While version 1.21 fails silently. Is there something else obvious I'm missing?
Thanks,
William Long
[1m[7m%[27m[1m[0m
[0m[27m[24m[Jwill@m1$ [K[?2004h[7msudo cu -l /dev/cu.usbserial-0001 -s
115200[27m
[KM[9C[27ms[27mu[27md[27mo[27m [27mc[27mu[27m [27m-[27ml[27m
[27m/[27md[27me[27mv[27m/[27mc[27mu[27m.[27mu[27ms[27mb[27ms[27me[27mr[27mi[27ma[27ml[27m-[27m0[27m0[27m0[27m1[27m
[27m-[27ms[27m [27m1[27m1[27m5[27m2[27m0[27m0[1B
[K[?2004l
Password:
Connected.
recover4.elf not found (6)
recovery.elf not found (6)
Read start4.elf bytes 2212384 hnd 0x000000dd hash 'bf07104c7821ae07'
Read fixup4.dat bytes 5421 hnd 0x000000d7 hash '4e7be95384e3e746'
0x00c03112 0x00000000 0x0000001f
MEM GPU: 76 ARM: 948 TOTAL: 1024
Starting start4.elf @ 0xfec00200 partition 0
MESS:00:00:04.961634:0: arasan: arasan_emmc_open
MESS:00:00:05.109823:0: brfs: File read: /mfs/sd/config.txt
MESS:00:00:05.112605:0: brfs: File read: 206 bytes
MESS:00:00:05.180020:0: brfs: File read: /mfs/sd/config.txt
MESS:00:00:05.198299:0: brfs: File read: 206 bytes
MESS:00:00:05.679885:0: gpioman: gpioman_get_pin_num: pin DISPLAY_DSI_PORT not
defined
MESS:00:00:05.687138:0: *** Restart logging
MESS:00:00:05.692201:0: hdmi: HDMI:hdmi_get_state is deprecated, use
hdmi_get_display_state instead
MESS:00:00:05.701497:0: hdmi: HDMI:hdmi_get_state is deprecated, use
hdmi_get_display_state instead
MESS:00:00:05.707431:0: HDMI0: hdmi_pixel_encoding: 300000000
MESS:00:00:05.712900:0: HDMI1: hdmi_pixel_encoding: 300000000
MESS:00:00:05.723099:0: dtb_file 'bcm2711-rpi-4-b.dtb'
MESS:00:00:05.729694:0: brfs: File read: /mfs/sd/bcm2711-rpi-4-b.dtb
MESS:00:00:05.732941:0: Loading 'bcm2711-rpi-4-b.dtb' to 0x1f0000 size 0xb97c
MESS:00:00:05.752005:0: brfs: File read: 47484 bytes
MESS:00:00:05.808878:0: brfs: File read: /mfs/sd/config.txt
MESS:00:00:05.811442:0: brfs: File read: 206 bytes
MESS:00:00:05.816776:0: brfs: File read: /mfs/sd/overlays/miniuart-bt.dtbo
MESS:00:00:05.842244:0: Loaded overlay 'miniuart-bt'
MESS:00:00:05.895786:0: brfs: File read: 1819 bytes
MESS:00:00:05.897766:0: Failed to open command line file 'cmdline.txt'
MESS:00:00:07.145770:0: brfs: File read: /mfs/sd/RPI_EFI.fd
MESS:00:00:07.148232:0: Loading 'RPI_EFI.fd' to 0x0 size 0x1f0000
MESS:00:00:07.154056:0: No compatible kernel found
MESS:00:00:07.158559:0: Device tree loaded to 0x1f0000 (size 0xbdd0)
MESS:00:00:07.166285:0: uart: Set PL011 baud rate to 103448.300000 Hz
MESS:00:00:07.173716:0: uart: Baud rate change done...
MESS:00:00:07.175735:0: uart: Baud rate change done...
MESS:00:00:07.180864:0: gpioman: gpioman_get_pin_num: pin SDCARD_CONTROL_POWER
not defined
NOTICE: BL31: v2.3():v2.3
NOTICE: BL31: Built : 10:40:51, Apr 21 2020
UEFI firmware (version UEFI Firmware v1.21 built at 13:07:48 on Nov 13 2020)
[2J[04D[=3h[2J[09D[0m[35m[40m[0m[37m[40mESC (setup), F1 (shell),
ENTER (boot)......disks: sd0* sd1 sd2
>> OpenBSD/arm64 BOOTAA64 1.22
|/-\|/boot>
-\|cannot open sd0a:/etc/random.seed: No such file or directory
booting sd0a:/bsd:
/-\|/3061308-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/+1283676-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|+12718640/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/+646240-
[268894\|/-\|/-\|/-\|/-\+91+726408|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|+294645/-\|/-\|/-\|/-\|/-]=0x1
3fa0d0
FACP CSRT DBG2 GTDT IORT APIC PPTT SPCR
Copyright (c) 1982, 1986, 1989, 1991, 1993
The Regents of the University of California. All rights reserved.
Copyright (c) 1995-2025 OpenBSD. All rights reserved. https://www.OpenBSD.org
OpenBSD 7.8 (RAMDISK) #38: Sun Oct 12 18:49:37 MDT 2025
[email protected]:/usr/src/sys/arch/arm64/compile/RAMDISK
real mem = 3132276736 (2987MB)
avail mem = 2994978816 (2856MB)
random: good seed from bootblocks
mainbus0 at root: ACPI
psci0 at mainbus0: PSCI 1.1, SMCCC 1.2
efi0 at mainbus0: UEFI 2.7
efi0: https://github.com/pftf/RPi4 rev 0x10000
smbios0 at efi0: SMBIOS 3.3.0
smbios0: vendor https://github.com/pftf/RPi4 version "UEFI Firmware v1.21" date
11/13/2020
smbios0: Raspberry Pi Foundation Raspberry Pi 4 Model B
cpu0 at mainbus0 mpidr 0: ARM Cortex-A72 r0p3
cpu0: 48KB 64b/line 3-way L1 PIPT I-cache, 32KB 64b/line 2-way L1 D-cache
cpu0: 1024KB 64b/line 16-way L2 cache
cpu0: CRC32,ASID16
ampintc0 at mainbus0 nirq 256, ncpu 4: "interrupt-controller"
agtimer0 at mainbus0: 54000 kHz
acpi0 at mainbus0: ACPI 6.3
acpi0: tables DSDT FACP CSRT DBG2 GTDT IORT APIC PPTT SPCR
acpiiort0 at acpi0
"BCM2854" at acpi0 not configured
"ACPI0004" at acpi0 not configured
xhci0 at acpi0 XHC0 addr 0x600000000/0x1000 irq 175, xHCI 1.0
usb0 at xhci0: USB revision 3.0
uhub0 at usb0 configuration 1 interface 0 "Generic xHCI root hub" rev 3.00/1.00
addr 1
"ACPI0004" at acpi0 not configured
"BCM2848" at acpi0 not configured
"BCM2850" at acpi0 not configured
"BCM2849" at acpi0 not configured
"BCM2835" at acpi0 not configured
"BCM2856" at acpi0 not configured
"BCM2845" at acpi0 not configured
"BCM2841" at acpi0 not configured
"BCM2841" at acpi0 not configured
"BCM2838" at acpi0 not configured
"BCM2839" at acpi0 not configured
"BCM2844" at acpi0 not configured
pluart0 at acpi0 URT0 addr 0xfe201000/0x1000 irq 153
pluart0: console
"BCM2836" at acpi0 not configured
"BCM2EA6" at acpi0 not configured
"MSFT8000" at acpi0 not configured
sdhc0 at acpi0 SDC1 addr 0xfe300000/0x100 irq 158
sdhc0: base clock frequency unknown
"BCM2855" at acpi0 not configured
bse0 at acpi0 ETH0 addr 0xfd580000/0x10000 irq 189: address dc:a6:32:68:a5:cc
brgphy0 at bse0 phy 1: BCM54210E, rev. 2
"PNP0C06" at acpi0 not configured
acpitz at acpi0 not configured
uhub1 at uhub0 port 1 configuration 1 interface 0 "VIA Labs USB2.0 Hub" rev
2.10/4.21 addr 2
umass0 at uhub1 port 1 configuration 1 interface 0 "Verbatim STORE N GO" rev
2.00/1.00 addr 3
umass0: using SCSI over Bulk-Only
scsibus0 at umass0: 2 targets, initiator 0
sd0 at scsibus0 targ 1 lun 0: <Verbatim, STORE N GO, 3.08> removable
serial.18a50304000000002610
sd0: 3823MB, 512 bytes/sector, 7829504 sectors
umass1 at uhub1 port 4 configuration 1 interface 0 "SanDisk Cruzer Glide" rev
2.00/1.26 addr 4
umass1: using SCSI over Bulk-Only
scsibus1 at umass1: 2 targets, initiator 0
sd1 at scsibus1 targ 1 lun 0: <SanDisk, Cruzer Glide, 1.26>
serial.07815575800315105240
sd1: 7633MB, 512 bytes/sector, 15633408 sectors
softraid0 at root
scsibus2 at softraid0: 256 targets
root on rd0a swap on rd0b dump on rd0b
WARNING: bad clock chip time
WARNING: CHECK AND RESET THE DATE!
erase ^?, werase ^W, kill ^U, intr ^C, status ^T
Welcome to the OpenBSD/arm64 7.8 installation program.
(I)nstall, (U)pgrade, (A)utoinstall or (S)hell? i
At any prompt except password prompts you can escape to a shell by
typing '!'. Default answers are shown in []'s and are selected by
pressing RETURN. You can exit this program at any time by pressing
Control-C, but this can leave your system in an inconsistent state.
Terminal type? [vt220]
System hostname? (short form, e.g. 'foo') router
Available network interfaces are: bse0 vlan0.
Network interface to configure? (name, lladdr, '?', or 'done') [bse0]
IPv4 address for bse0? (or 'autoconf' or 'none') [autoconf]
IPv6 address for bse0? (or 'autoconf' or 'none') [none]
Available network interfaces are: bse0 vlan0.
Network interface to configure? (name, lladdr, '?', or 'done') [done]
Using DNS domainname my.domain
DNS nameservers? (IP address list or 'none') [none] 9.9.9.9
Password for root account? (will not echo)
Password for root account? (again)
Start sshd(8) by default? [yes]
Setup a user? (enter a lower-case loginname, or 'no') [no] will
Full name for user will? [will]
Password for user will? (will not echo)
Password for user will? (again)
WARNING: root is targeted by password guessing attacks, pubkeys are safer.
Allow root ssh login? (yes, no, prohibit-password) [no]
Available disks are: sd0 sd1.
Which disk is the root disk? ('?' for details) [sd0] ?
sd0: Verbatim, STORE N GO, 3.08 serial.18a50304000000002610 (3.7G)
sd1: SanDisk, Cruzer Glide, 1.26 serial.07815575800315105240 (7.5G)
Available disks are: sd0 sd1.
Which disk is the root disk? ('?' for details) [sd0]
Encrypt the root disk with a (p)assphrase or (k)eydisk? [no]
Disk: sd0 geometry: 487/255/63 [7829504 Sectors]
Offset: 0 Signature: 0xAA55
Starting Ending LBA Info:
#: id C H S - C H S [ start: size ]
-------------------------------------------------------------------------------
*0: 0C 2 10 9 - 35 47 12 [ 32768: 532480 ] FAT32 (LBA)
1: 00 0 0 0 - 0 0 0 [ 0: 0 ] Unused
2: 00 0 0 0 - 0 0 0 [ 0: 0 ] Unused
3: A6 35 47 13 - 487 92 53 [ 565248: 7264256 ] OpenBSD
Use (W)hole disk or (E)dit the MBR? [whole] e W
Creating a msdos partition and an OpenBSD partition for rest of sd0...cu: Got
hangup signal
Disconnected.
[1m[7m%[27m[1m[0m
[0m[27m[24m[Jwill@m1$ [K[?2004h[?2004l
Script started on Sun Apr 12 13:00:47 2026
Script done on Sun Apr 12 13:05:24 2026
[1m[7m%[27m[1m[0m
[0m[27m[24m[Jwill@m1$ [K[?2004hssudo [7mcu -l /dev/cu.usbserial-0001 -s
115200[27m[38D[27mc[27mu[27m [27m-[27ml[27m
[27m/[27md[27me[27mv[27m/[27mc[27mu[27m.[27mu[27ms[27mb[27ms[27me[27mr[27mi[27ma[27ml[27m-[27m0[27m0[27m0[27m1[27m
[27m-[27ms[27m [27m1[27m1[27m5[27m2[27m0[27m0[?2004l
Password:
Connected.
recover4.elf not found (6)
recovery.elf not found (6)
Read start4.elf bytes 2303680 hnd 0x0000027f hash '77260733037721d2'
Read fixup4.dat bytes 5498 hnd 0x0000027d hash '80fde48a87ec7ee9'
0x00c03112 0x00000000 0x00003fff
MEM GPU: 76 ARM: 948 TOTAL: 1024
Starting start4.elf @ 0xfec00200 partition 0
MESS:00:00:04.742354:0: arasan: arasan_emmc_open
MESS:00:00:04.744012:0: arasan: arasan_emmc_set_clock C0: 0x00800000 C1:
0x000e0047 emmc: 200000000 actual: 390625 div: 0x00000100 target: 400000 min:
400000 max: 400000 delay: 5
MESS:00:00:04.864248:0: arasan: arasan_emmc_set_clock C0: 0x00800000 C1:
0x000e0047 emmc: 200000000 actual: 390625 div: 0x00000100 target: 400000 min:
400000 max: 400000 delay: 5
MESS:00:00:04.877118:0: arasan: arasan_emmc_set_clock C0: 0x00800f00 C1:
0x000e0047 emmc: 200000000 actual: 390625 div: 0x00000100 target: 400000 min:
390000 max: 400000 delay: 5
MESS:00:00:04.910868:0: boot-part: 0 fs-type: 0
MESS:00:00:04.912281:0: boot-part: 0 fs-type: 3
MESS:00:00:04.916665:0: arasan: arasan_emmc_set_clock C0: 0x00800f06 C1:
0x000e0207 emmc: 200000000 actual: 50000000 div: 0x00000002 target: 50000000
min: 0 max: 50000000 delay: 1
MESS:00:00:04.935231:0: brfs: File read: /mfs/sd/config.txt
MESS:00:00:04.937991:0: board: boardrev c03112 otp c03112
MESS:00:00:04.942893:0: brfs: File read: 243 bytes
MESS:00:00:04.969438:0: HDMI0:EDID error reading EDID block 0 attempt 0
MESS:00:00:04.973946:0: HDMI0:EDID giving up on reading EDID block 0
MESS:00:00:04.991080:0: HDMI1:EDID error reading EDID block 0 attempt 0
MESS:00:00:04.995581:0: HDMI1:EDID giving up on reading EDID block 0
MESS:00:00:05.001408:0: brfs: File read: /mfs/sd/config.txt
MESS:00:00:05.488266:0: gpioman: gpioman_get_pin_num: pin DISPLAY_DSI_PORT not
defined
MESS:00:00:05.493814:0: gpioman: gpioman_get_pin_num: pin DISPLAY_DSI_PORT not
defined
MESS:00:00:05.502848:0: *** Restart logging
MESS:00:00:05.504623:0: brfs: File read: 243 bytes
MESS:00:00:05.514413:0: hdmi: HDMI0:EDID error reading EDID block 0 attempt 0
MESS:00:00:05.519443:0: hdmi: HDMI0:EDID giving up on reading EDID block 0
MESS:00:00:05.530065:0: hdmi: HDMI0:EDID error reading EDID block 0 attempt 0
MESS:00:00:05.535090:0: hdmi: HDMI0:EDID giving up on reading EDID block 0
MESS:00:00:05.540688:0: hdmi: HDMI:hdmi_get_state is deprecated, use
hdmi_get_display_state instead
MESS:00:00:05.554479:0: hdmi: HDMI1:EDID error reading EDID block 0 attempt 0
MESS:00:00:05.559501:0: hdmi: HDMI1:EDID giving up on reading EDID block 0
MESS:00:00:05.570122:0: hdmi: HDMI1:EDID error reading EDID block 0 attempt 0
MESS:00:00:05.575150:0: hdmi: HDMI1:EDID giving up on reading EDID block 0
MESS:00:00:05.580748:0: hdmi: HDMI:hdmi_get_state is deprecated, use
hdmi_get_display_state instead
MESS:00:00:05.589513:0: HDMI0: hdmi_pixel_encoding: 300000000
MESS:00:00:05.594981:0: HDMI1: hdmi_pixel_encoding: 300000000
MESS:00:00:05.610895:0: dtb_file 'bcm2711-rpi-4-b.dtb'
MESS:00:00:05.618528:0: brfs: File read: /mfs/sd/bcm2711-rpi-4-b.dtb
MESS:00:00:05.621776:0: Loaded 'bcm2711-rpi-4-b.dtb' to 0x3e0000 size 0xd3f8
MESS:00:00:05.642024:0: brfs: File read: 54264 bytes
MESS:00:00:05.665466:0: brfs: File read: /mfs/sd/config.txt
MESS:00:00:05.668034:0: brfs: File read: 243 bytes
MESS:00:00:05.673471:0: brfs: File read: /mfs/sd/overlays/miniuart-bt.dtbo
MESS:00:00:05.699542:0: Loaded overlay 'miniuart-bt'
MESS:00:00:05.743598:0: brfs: File read: 1566 bytes
MESS:00:00:05.746513:0: brfs: File read: /mfs/sd/overlays/upstream-pi4.dtbo
MESS:00:00:05.813273:0: Loaded overlay 'upstream-pi4'
MESS:00:00:05.981778:0: brfs: File read: 2775 bytes
MESS:00:00:05.983758:0: Failed to open command line file 'cmdline.txt'
MESS:00:00:06.443722:0: brfs: File read: /mfs/sd/RPI_EFI.fd
MESS:00:00:06.446181:0: Loaded 'RPI_EFI.fd' to 0x0 size 0x3d0000
MESS:00:00:06.451920:0: No compatible kernel found
MESS:00:00:06.456422:0: Device tree loaded to 0x3e0000 (size 0xd8c3)
MESS:00:00:06.464087:0: uart: Set PL011 baud rate to 103448.300000 Hz
MESS:00:00:06.471573:0: uart: Baud rate change done...
MESS:00:00:06.473595:0: uart: Baud rate change done...
MESS:00:00:06.480362:0: gpioman: gpioman_get_pin_num: pin SDCARD_CONTROL_POWER
not defined
MESS:00:00:06.486597:0: Watchdog stopped
MESS:00:00:06.490094:0: arm_loader: Starting ARM with 948MB
NOTICE: BL31: v2.9(release):v2.9
NOTICE: BL31: Built : 17:09:05, May 24 2023
UEFI firmware (version UEFI Firmware v1.51 built at 16:49:18 on Mar 22 2026)
[2J[004D[=3h[2J[009DESC (setup), F1 (shell), ENTER (boot)..[2J[043DUEFI
Interactive Shell v2.2
EDK II
UEFI v2.70 (https://github.com/pftf/RPi4, 0x00010000)
[1m[33m[40mMapping table[0m[37m[40m
[1m[33m[40m FS0:[0m[37m[40m
[1m[37m[40mAlias(s):[0m[37m[40mHD0a0a0b:;BLK1:
PcieRoot(0x0)/Pci(0x0,0x0)/Pci(0x0,0x0)/USB(0x0,0x0)/USB(0x0,0x0)/HD(1
,MBR,0x00000000)
[1m[33m[40m FS1:[0m[37m[40m
[1m[37m[40mAlias(s):[0m[37m[40mHD1b:;BLK4:
VenHw(100C2CFA-B586-4198-9B4C-1683D195B1DA)/HD(1,MBR,0x00000000)
[1m[33m[40m BLK3:[0m[37m[40m [1m[37m[40mAlias(s):[0m[37m[40m
VenHw(100C2CFA-B586-4198-9B4C-1683D195B1DA)
[1m[33m[40m BLK0:[0m[37m[40m [1m[37m[40mAlias(s):[0m[37m[40m
PcieRoot(0x0)/Pci(0x0,0x0)/Pci(0x0,0x0)/USB(0x0,0x0)/USB(0x0,0x0)
[1m[33m[40m BLK2:[0m[37m[40m [1m[37m[40mAlias(s):[0m[37m[40m
PcieRoot(0x0)/Pci(0x0,0x0)/Pci(0x0,0x0)/USB(0x0,0x0)/USB(0x0,0x0)/HD(4
,MBR,0x00000000)
Press [1m[37m[40mESC[0m[37m[40m in 5 seconds to skip
[1m[33m[40mstartup.nsh[0m[37m[40m or any other key to
continue.[072DPress [1m[37m[40mESC[0m[37m[40m in 4 seconds to skip
[1m[33m[40mstartup.nsh[0m[37m[40m or any other key to
continue.[072DPress [1m[37m[40mESC[0m[37m[40m in 3 seconds to skip
[1m[33m[40mstartup.nsh[0m[37m[40m or any other key to
continue.[072DPress [1m[37m[40mESC[0m[37m[40m in 2 seconds to skip
[1m[33m[40mstartup.nsh[0m[37m[40m or any other key to
continue.[072DPress [1m[37m[40mESC[0m[37m[40m in 1 seconds to skip
[1m[33m[40mstartup.nsh[0m[37m[40m or any other key to continue.
[1m[33m[40mShell> [0m[37m[40mbootaa64.efi
disks: sd0* sd1
>> OpenBSD/arm64 BOOTAA64 1.22
|/-\|/boot>
-\|cannot open sd0a:/etc/random.seed: No such file or directory
booting sd0a:/bsd:
/-\|/3061308-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/+1283676-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|+12718640/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/+646240-
[268894\|/-\|/-\|/-\|/-\+91+726408|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|+294645/-\|/-\|/-\|/-\|/-]=0x1
3fa0d0
FACP CSRT DBG2 GTDT APIC PPTT SPCR SSDT SSDT
Copyright (c) 1982, 1986, 1989, 1991, 1993
The Regents of the University of California. All rights reserved.
Copyright (c) 1995-2025 OpenBSD. All rights reserved. https://www.OpenBSD.org
OpenBSD 7.8 (RAMDISK) #38: Sun Oct 12 18:49:37 MDT 2025
[email protected]:/usr/src/sys/arch/arm64/compile/RAMDISK
real mem = 3127017472 (2982MB)
avail mem = 2989903872 (2851MB)
random: good seed from bootblocks
mainbus0 at root: ACPI
psci0 at mainbus0: PSCI 1.1, SMCCC 1.2
efi0 at mainbus0: UEFI 2.7
efi0: https://github.com/pftf/RPi4 rev 0x10000
smbios0 at efi0: SMBIOS 3.3.0
smbios0: vendor https://github.com/pftf/RPi4 version "UEFI Firmware v1.51" date
03/22/2026
smbios0: Raspberry Pi Foundation Raspberry Pi 4 Model B
cpu0 at mainbus0 mpidr 0: ARM Cortex-A72 r0p3
cpu0: 48KB 64b/line 3-way L1 PIPT I-cache, 32KB 64b/line 2-way L1 D-cache
cpu0: 1024KB 64b/line 16-way L2 cache
cpu0: CRC32,ASID16
ampintc0 at mainbus0 nirq 256, ncpu 4: "interrupt-controller"
agtimer0 at mainbus0: 54000 kHz
acpi0 at mainbus0: ACPI 6.3
acpi0: tables DSDT FACP CSRT DBG2 GTDT APIC PPTT SPCR SSDT SSDT
"BCM2854" at acpi0 not configured
"ACPI0004" at acpi0 not configured
"BCM2848" at acpi0 not configured
"BCM2850" at acpi0 not configured
"BCM2849" at acpi0 not configured
"BCM2835" at acpi0 not configured
"BCM2856" at acpi0 not configured
"BCM2845" at acpi0 not configured
"BCM2841" at acpi0 not configured
"BCM2841" at acpi0 not configured
"BCM2838" at acpi0 not configured
"BCM2839" at acpi0 not configured
"BCM2844" at acpi0 not configured
pluart0 at acpi0 URT0 addr 0xfe201000/0x1000 irq 153
pluart0: console
"BCM2836" at acpi0 not configured
"BCM2EA6" at acpi0 not configured
"MSFT8000" at acpi0 not configured
sdhc0 at acpi0 SDC1 addr 0xfe300000/0x100 irq 158
sdhc0: SDHC 3.00, 250 MHz base clock
sdmmc0 at sdhc0: 4-bit, sd high-speed, mmc high-speed
bse0 at acpi0 ETH0 addr 0xfd580000/0x10000 irq 189: address 00:00:00:00:00:00
brgphy0 at bse0 phy 1: BCM54210E, rev. 2
"PNP0C06" at acpi0 not configured
"ACPI0004" at acpi0 not configured
sdhc1 at acpi0 SDC3 addr 0xfe340000/0x100 irq 158
sdhc1: SDHC 3.00, 100 MHz base clock
sdmmc1 at sdhc1: 8-bit, sd high-speed, mmc high-speed
"ACPI0004" at acpi0 not configured
xhci0 at acpi0 XHC0 addr 0x600000000/0x1000 irq 175, xHCI 1.0
usb0 at xhci0: USB revision 3.0
uhub0 at usb0 configuration 1 interface 0 "Generic xHCI root hub" rev 3.00/1.00
addr 1
acpitz at acpi0 not configured
scsibus0 at sdmmc1: 2 targets, initiator 0
sd0 at scsibus0 targ 1 lun 0: <SD/MMC, 00000, 0065>
sd0: 29721MB, 512 bytes/sector, 60868608 sectors
bwfm0 at sdmmc0 function 1
manufacturer 0x02d0, product 0xa9a6 at sdmmc0 function 2 not configured
manufacturer 0x02d0, product 0xa9a6 at sdmmc0 function 3 not configured
uhub1 at uhub0 port 1 configuration 1 interface 0 "VIA Labs USB2.0 Hub" rev
2.10/4.21 addr 2
umass0 at uhub1 port 1 configuration 1 interface 0 "Verbatim STORE N GO" rev
2.00/1.00 addr 3
umass0: using SCSI over Bulk-Only
scsibus1 at umass0: 2 targets, initiator 0
sd1 at scsibus1 targ 1 lun 0: <Verbatim, STORE N GO, 3.08> removable
serial.18a50304000000002610
sd1: 3823MB, 512 bytes/sector, 7829504 sectors
softraid0 at root
scsibus2 at softraid0: 256 targets
root on rd0a swap on rd0b dump on rd0b
WARNING: CHECK AND RESET THE DATE!
bwfm0: failed loadfirmware of file brcmfmac43455-sdio.openbsd,acpi.bin
erase ^?, werase ^W, kill ^U, intr ^C, status ^T
Welcome to the OpenBSD/arm64 7.8 installation program.
(I)nstall, (U)pgrade, (A)utoinstall or (S)hell? i
At any prompt except password prompts you can escape to a shell by
typing '!'. Default answers are shown in []'s and are selected by
pressing RETURN. You can exit this program at any time by pressing
Control-C, but this can leave your system in an inconsistent state.
Terminal type? [vt220]
System hostname? (short form, e.g. 'foo') router
Available network interfaces are: bse0 bwfm0 vlan0.
Network interface to configure? (name, lladdr, '?', or 'done') [bse0]
IPv4 address for bse0? (or 'autoconf' or 'none') [autoconf]
No dhcp address on interface bse0 in 30 seconds.
IPv6 address for bse0? (or 'autoconf' or 'none') [none] cu: Got hangup signal
Disconnected.
[1m[7m%[27m[1m[0m
[0m[27m[24m[Jwill@m1$ [K[?2004h[?2004l
Script started on Sun Apr 12 11:52:41 2026
Script done on Sun Apr 12 11:54:11 2026
