On 12/09/2013 04:47 PM, Mauro Carvalho Chehab wrote:
> Em Fri, 6 Dec 2013 11:17:09 +0100
> Hans Verkuil <hverk...@xs4all.nl> escreveu:
>
>> From: Dinesh Ram <dinesh....@cern.ch>
>>
>> This is the USB driver for the Silicon Labs development board.
>> It contains the Si4713 FM transmitter chip.
>>
>> Signed-off-by: Dinesh Ram <dinesh....@cern.ch>
>> Signed-off-by: Hans Verkuil <hans.verk...@cisco.com>
>> Tested-by: Eduardo Valentin <edubez...@gmail.com>
>> Acked-by: Eduardo Valentin <edubez...@gmail.com>
>> ---
>> drivers/media/radio/si4713/Kconfig | 15 +
>> drivers/media/radio/si4713/Makefile | 1 +
>> drivers/media/radio/si4713/radio-usb-si4713.c | 540
>> ++++++++++++++++++++++++++
>> 3 files changed, 556 insertions(+)
>> create mode 100644 drivers/media/radio/si4713/radio-usb-si4713.c
>>
>> diff --git a/drivers/media/radio/si4713/Kconfig
>> b/drivers/media/radio/si4713/Kconfig
>> index ec640b8..a7c3ba8 100644
>> --- a/drivers/media/radio/si4713/Kconfig
>> +++ b/drivers/media/radio/si4713/Kconfig
>> @@ -1,3 +1,18 @@
>> +config USB_SI4713
>> + tristate "Silicon Labs Si4713 FM Radio Transmitter support with USB"
>> + depends on USB && RADIO_SI4713
>> + select SI4713
>> + ---help---
>> + This is a driver for USB devices with the Silicon Labs SI4713
>> + chip. Currently these devices are known to work.
>> + - 10c4:8244: Silicon Labs FM Transmitter USB device.
>> +
>> + Say Y here if you want to connect this type of radio to your
>> + computer's USB port.
>> +
>> + To compile this driver as a module, choose M here: the
>> + module will be called radio-usb-si4713.
>> +
>> config PLATFORM_SI4713
>> tristate "Silicon Labs Si4713 FM Radio Transmitter support with I2C"
>> depends on I2C && RADIO_SI4713
>> diff --git a/drivers/media/radio/si4713/Makefile
>> b/drivers/media/radio/si4713/Makefile
>> index a8c1194..ddaaf92 100644
>> --- a/drivers/media/radio/si4713/Makefile
>> +++ b/drivers/media/radio/si4713/Makefile
>> @@ -3,4 +3,5 @@
>> #
>>
>> obj-$(CONFIG_I2C_SI4713) += si4713.o
>> +obj-$(CONFIG_USB_SI4713) += radio-usb-si4713.o
>> obj-$(CONFIG_PLATFORM_SI4713) += radio-platform-si4713.o
>> diff --git a/drivers/media/radio/si4713/radio-usb-si4713.c
>> b/drivers/media/radio/si4713/radio-usb-si4713.c
>> new file mode 100644
>> index 0000000..d978844
>> --- /dev/null
>> +++ b/drivers/media/radio/si4713/radio-usb-si4713.c
>> @@ -0,0 +1,540 @@
>> +/*
>> + * Copyright 2013 Cisco Systems, Inc. and/or its affiliates.
>> + * All rights reserved.
>> + *
>> + * This program is free software; you may redistribute it and/or modify
>> + * it under the terms of the GNU General Public License as published by
>> + * the Free Software Foundation; version 2 of the License.
>> + *
>> + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
>> + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF
>> + * MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
>> + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT HOLDERS
>> + * BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER IN AN
>> + * ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN
>> + * CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE
>> + * SOFTWARE.
>> + */
>> +
>> +/* kernel includes */
>> +#include <linux/kernel.h>
>> +#include <linux/module.h>
>> +#include <linux/usb.h>
>> +#include <linux/init.h>
>> +#include <linux/slab.h>
>> +#include <linux/input.h>
>> +#include <linux/mutex.h>
>> +#include <linux/i2c.h>
>> +/* V4l includes */
>> +#include <linux/videodev2.h>
>> +#include <media/v4l2-common.h>
>> +#include <media/v4l2-device.h>
>> +#include <media/v4l2-ioctl.h>
>> +#include <media/v4l2-event.h>
>> +#include <media/si4713.h>
>> +
>> +#include "si4713.h"
>> +
>> +/* driver and module definitions */
>> +MODULE_AUTHOR("Dinesh Ram <dinesh....@cern.ch>");
>> +MODULE_DESCRIPTION("Si4713 FM Transmitter USB driver");
>> +MODULE_LICENSE("GPL v2");
>> +
>> +/* The Device announces itself as Cygnal Integrated Products, Inc. */
>> +#define USB_SI4713_VENDOR 0x10c4
>> +#define USB_SI4713_PRODUCT 0x8244
>> +
>> +#define BUFFER_LENGTH 64
>> +#define USB_TIMEOUT 1000
>> +#define USB_RESP_TIMEOUT 50000
>> +
>> +/* USB Device ID List */
>> +static struct usb_device_id usb_si4713_usb_device_table[] = {
>> + {USB_DEVICE_AND_INTERFACE_INFO(USB_SI4713_VENDOR, USB_SI4713_PRODUCT,
>> + USB_CLASS_HID, 0, 0) },
>> + { } /* Terminating entry */
>> +};
>> +
>> +MODULE_DEVICE_TABLE(usb, usb_si4713_usb_device_table);
>> +
>> +struct si4713_usb_device {
>> + struct usb_device *usbdev;
>> + struct usb_interface *intf;
>> + struct video_device vdev;
>> + struct v4l2_device v4l2_dev;
>> + struct v4l2_subdev *v4l2_subdev;
>> + struct mutex lock;
>> + struct i2c_adapter i2c_adapter;
>> +
>> + u8 *buffer;
>> +};
>> +
>> +static inline struct si4713_usb_device *to_si4713_dev(struct v4l2_device
>> *v4l2_dev)
>> +{
>> + return container_of(v4l2_dev, struct si4713_usb_device, v4l2_dev);
>> +}
>> +
>> +static int vidioc_querycap(struct file *file, void *priv,
>> + struct v4l2_capability *v)
>> +{
>> + struct si4713_usb_device *radio = video_drvdata(file);
>> +
>> + strlcpy(v->driver, "radio-usb-si4713", sizeof(v->driver));
>> + strlcpy(v->card, "Si4713 FM Transmitter", sizeof(v->card));
>> + usb_make_path(radio->usbdev, v->bus_info, sizeof(v->bus_info));
>> + v->device_caps = V4L2_CAP_MODULATOR | V4L2_CAP_RDS_OUTPUT;
>> + v->capabilities = v->device_caps | V4L2_CAP_DEVICE_CAPS;
>> +
>> + return 0;
>> +}
>> +
>> +static int vidioc_g_modulator(struct file *file, void *priv,
>> + struct v4l2_modulator *vm)
>> +{
>> + struct si4713_usb_device *radio = video_drvdata(file);
>> +
>> + return v4l2_subdev_call(radio->v4l2_subdev, tuner, g_modulator, vm);
>> +}
>> +
>> +static int vidioc_s_modulator(struct file *file, void *priv,
>> + const struct v4l2_modulator *vm)
>> +{
>> + struct si4713_usb_device *radio = video_drvdata(file);
>> +
>> + return v4l2_subdev_call(radio->v4l2_subdev, tuner, s_modulator, vm);
>> +}
>> +
>> +static int vidioc_s_frequency(struct file *file, void *priv,
>> + const struct v4l2_frequency *vf)
>> +{
>> + struct si4713_usb_device *radio = video_drvdata(file);
>> +
>> + return v4l2_subdev_call(radio->v4l2_subdev, tuner, s_frequency, vf);
>> +}
>> +
>> +static int vidioc_g_frequency(struct file *file, void *priv,
>> + struct v4l2_frequency *vf)
>> +{
>> + struct si4713_usb_device *radio = video_drvdata(file);
>> +
>> + return v4l2_subdev_call(radio->v4l2_subdev, tuner, g_frequency, vf);
>> +}
>> +
>> +static const struct v4l2_ioctl_ops usb_si4713_ioctl_ops = {
>> + .vidioc_querycap = vidioc_querycap,
>> + .vidioc_g_modulator = vidioc_g_modulator,
>> + .vidioc_s_modulator = vidioc_s_modulator,
>> + .vidioc_g_frequency = vidioc_g_frequency,
>> + .vidioc_s_frequency = vidioc_s_frequency,
>> + .vidioc_log_status = v4l2_ctrl_log_status,
>> + .vidioc_subscribe_event = v4l2_ctrl_subscribe_event,
>> + .vidioc_unsubscribe_event = v4l2_event_unsubscribe,
>> +};
>> +
>> +/* File system interface */
>> +static const struct v4l2_file_operations usb_si4713_fops = {
>> + .owner = THIS_MODULE,
>> + .open = v4l2_fh_open,
>> + .release = v4l2_fh_release,
>> + .poll = v4l2_ctrl_poll,
>> + .unlocked_ioctl = video_ioctl2,
>> +};
>> +
>> +static void usb_si4713_video_device_release(struct v4l2_device *v4l2_dev)
>> +{
>> + struct si4713_usb_device *radio = to_si4713_dev(v4l2_dev);
>> + struct i2c_adapter *adapter = &radio->i2c_adapter;
>> +
>> + i2c_del_adapter(adapter);
>> + v4l2_device_unregister(&radio->v4l2_dev);
>> + kfree(radio->buffer);
>> + kfree(radio);
>> +}
>> +
>> +/*
>> + * This command sequence emulates the behaviour of the Windows driver.
>> + * The structure of these commands was determined by sniffing the
>> + * usb traffic of the device during startup.
>> + * Most likely, these commands make some queries to the device.
>> + * Commands are sent to enquire parameters like the bus mode,
>> + * component revision, boot mode, the device serial number etc.
>> + *
>> + * These commands are necessary to be sent in this order during startup.
>> + * The device fails to powerup if these commands are not sent.
>> + *
>> + * The complete list of startup commands is given in the start_seq table
>> below.
>> + */
>> +static int si4713_send_startup_command(struct si4713_usb_device *radio)
>> +{
>> + unsigned long until_jiffies = jiffies +
>> usecs_to_jiffies(USB_RESP_TIMEOUT) + 1;
>> + u8 *buffer = radio->buffer;
>> + int retval;
>> +
>> + /* send the command */
>> + retval = usb_control_msg(radio->usbdev, usb_sndctrlpipe(radio->usbdev,
>> 0),
>> + 0x09, 0x21, 0x033f, 0, radio->buffer,
>> + BUFFER_LENGTH, USB_TIMEOUT);
>> + if (retval < 0)
>> + return retval;
>> +
>> + for (;;) {
>> + /* receive the response */
>> + retval = usb_control_msg(radio->usbdev,
>> usb_rcvctrlpipe(radio->usbdev, 0),
>> + 0x01, 0xa1, 0x033f, 0, radio->buffer,
>> + BUFFER_LENGTH, USB_TIMEOUT);
>> + if (retval < 0)
>> + return retval;
>> + if (!radio->buffer[1]) {
>> + /* USB traffic sniffing showed that some commands
>> require
>> + * additional checks. */
>> + switch (buffer[1]) {
>> + case 0x32:
>> + if (radio->buffer[2] == 0)
>> + return 0;
>> + break;
>> + case 0x14:
>> + case 0x12:
>> + if (radio->buffer[2] & SI4713_CTS)
>> + return 0;
>> + break;
>> + case 0x06:
>> + if ((radio->buffer[2] & SI4713_CTS) &&
>> radio->buffer[9] == 0x08)
>> + return 0;
>> + break;
>> + default:
>> + return 0;
>> + }
>> + }
>> + if (time_is_before_jiffies(until_jiffies))
>> + return -EIO;
>
> According with include/linux/jiffies.h:
>
> time_is_before_jiffies(a) return true if a is before jiffies.
>
> I suspect that you want to do just the opposite here: to return -EIO if
> you passed the timeout given by until_jiffies.
You are correct.
>
>
>> + msleep(3);
>> + }
>> +
>> + return retval;
>> +}
>> +
>> +struct si4713_start_seq_table {
>> + int len;
>> + u8 payload[8];
>> +};
>> +
>> +/*
>> + * Some of the startup commands that could be recognized are :
>> + * (0x03): Get serial number of the board (Response : CB000-00-00)
>> + * (0x06, 0x03, 0x03, 0x08, 0x01, 0x0f) : Get Component revision
>> + */
>> +struct si4713_start_seq_table start_seq[] = {
>> +
>> + { 1, { 0x03 } },
>> + { 2, { 0x32, 0x7f } },
>> + { 6, { 0x06, 0x03, 0x03, 0x08, 0x01, 0x0f } },
>> + { 2, { 0x14, 0x02 } },
>> + { 2, { 0x09, 0x90 } },
>> + { 3, { 0x08, 0x90, 0xfa } },
>> + { 2, { 0x36, 0x01 } },
>> + { 2, { 0x05, 0x03 } },
>> + { 7, { 0x06, 0x00, 0x06, 0x0e, 0x01, 0x0f, 0x05 } },
>> + { 1, { 0x12 } },
>> + /* Commands that are sent after pressing the 'Initialize'
>> + button in the windows application */
>> + { 1, { 0x03 } },
>> + { 1, { 0x01 } },
>> + { 2, { 0x09, 0x90 } },
>> + { 3, { 0x08, 0x90, 0xfa } },
>> + { 1, { 0x34 } },
>> + { 2, { 0x35, 0x01 } },
>> + { 2, { 0x36, 0x01 } },
>> + { 2, { 0x30, 0x09 } },
>> + { 4, { 0x30, 0x06, 0x00, 0xe2 } },
>> + { 3, { 0x31, 0x01, 0x30 } },
>> + { 3, { 0x31, 0x04, 0x09 } },
>> + { 2, { 0x05, 0x02 } },
>> + { 6, { 0x06, 0x03, 0x03, 0x08, 0x01, 0x0f } },
>> +};
>> +
>> +static int si4713_start_seq(struct si4713_usb_device *radio)
>> +{
>> + int retval = 0;
>> + int i;
>> +
>> + radio->buffer[0] = 0x3f;
>> +
>> + for (i = 0; i < ARRAY_SIZE(start_seq); i++) {
>> + int len = start_seq[i].len;
>> + u8 *payload = start_seq[i].payload;
>> +
>> + memcpy(radio->buffer + 1, payload, len);
>> + memset(radio->buffer + len + 1, 0, BUFFER_LENGTH - 1 - len);
>> + retval = si4713_send_startup_command(radio);
>> + }
>> +
>> + return retval;
>> +}
>> +
>> +static struct i2c_board_info si4713_board_info = {
>> + I2C_BOARD_INFO("si4713", SI4713_I2C_ADDR_BUSEN_HIGH),
>> +};
>> +
>> +struct si4713_command_table {
>> + int command_id;
>> + u8 payload[8];
>> +};
>> +
>> +/*
>> + * Structure of a command :
>> + * Byte 1 : 0x3f (always)
>> + * Byte 2 : 0x06 (send a command)
>> + * Byte 3 : Unknown
>> + * Byte 4 : Number of arguments + 1 (for the command byte)
>> + * Byte 5 : Number of response bytes
>> + */
>> +struct si4713_command_table command_table[] = {
>> +
>> + { SI4713_CMD_POWER_UP, { 0x00, SI4713_PWUP_NARGS + 1,
>> SI4713_PWUP_NRESP} },
>> + { SI4713_CMD_GET_REV, { 0x03, 0x01, SI4713_GETREV_NRESP } },
>> + { SI4713_CMD_POWER_DOWN, { 0x00, 0x01, SI4713_PWDN_NRESP} },
>> + { SI4713_CMD_SET_PROPERTY, { 0x00, SI4713_SET_PROP_NARGS + 1,
>> SI4713_SET_PROP_NRESP } },
>> + { SI4713_CMD_GET_PROPERTY, { 0x00, SI4713_GET_PROP_NARGS + 1,
>> SI4713_GET_PROP_NRESP } },
>> + { SI4713_CMD_TX_TUNE_FREQ, { 0x03, SI4713_TXFREQ_NARGS + 1,
>> SI4713_TXFREQ_NRESP } },
>> + { SI4713_CMD_TX_TUNE_POWER, { 0x03, SI4713_TXPWR_NARGS + 1,
>> SI4713_TXPWR_NRESP } },
>> + { SI4713_CMD_TX_TUNE_MEASURE, { 0x03, SI4713_TXMEA_NARGS + 1,
>> SI4713_TXMEA_NRESP } },
>> + { SI4713_CMD_TX_TUNE_STATUS, { 0x00, SI4713_TXSTATUS_NARGS + 1,
>> SI4713_TXSTATUS_NRESP } },
>> + { SI4713_CMD_TX_ASQ_STATUS, { 0x03, SI4713_ASQSTATUS_NARGS + 1,
>> SI4713_ASQSTATUS_NRESP } },
>> + { SI4713_CMD_GET_INT_STATUS, { 0x03, 0x01, SI4713_GET_STATUS_NRESP }
>> },
>> + { SI4713_CMD_TX_RDS_BUFF, { 0x03, SI4713_RDSBUFF_NARGS + 1,
>> SI4713_RDSBUFF_NRESP } },
>> + { SI4713_CMD_TX_RDS_PS, { 0x00, SI4713_RDSPS_NARGS + 1,
>> SI4713_RDSPS_NRESP } },
>> +};
>> +
>> +static int send_command(struct si4713_usb_device *radio, u8 *payload, char
>> *data, int len)
>> +{
>> + int retval;
>> +
>> + radio->buffer[0] = 0x3f;
>> + radio->buffer[1] = 0x06;
>> +
>> + memcpy(radio->buffer + 2, payload, 3);
>> + memcpy(radio->buffer + 5, data, len);
>> + memset(radio->buffer + 5 + len, 0, BUFFER_LENGTH - 5 - len);
>> +
>> + /* send the command */
>> + retval = usb_control_msg(radio->usbdev, usb_sndctrlpipe(radio->usbdev,
>> 0),
>> + 0x09, 0x21, 0x033f, 0, radio->buffer,
>> + BUFFER_LENGTH, USB_TIMEOUT);
>> +
>> + return retval < 0 ? retval : 0;
>> +}
>> +
>> +static int si4713_i2c_read(struct si4713_usb_device *radio, char *data, int
>> len)
>> +{
>> + unsigned long until_jiffies = jiffies +
>> usecs_to_jiffies(USB_RESP_TIMEOUT) + 1;
>> + int retval;
>> +
>> + /* receive the response */
>> + for (;;) {
>> + retval = usb_control_msg(radio->usbdev,
>> + usb_rcvctrlpipe(radio->usbdev, 0),
>> + 0x01, 0xa1, 0x033f, 0, radio->buffer,
>> + BUFFER_LENGTH, USB_TIMEOUT);
>> + if (retval < 0)
>> + return retval;
>> +
>> + /*
>> + * Check that we get a valid reply back (buffer[1] == 0) and
>> + * that CTS is set before returning, otherwise we wait and try
>> + * again. The i2c driver also does the CTS check, but the
>> timeouts
>> + * used there are much too small for this USB driver, so we wait
>> + * for it here.
>> + */
>> + if (radio->buffer[1] == 0 && (radio->buffer[2] & SI4713_CTS)) {
>> + memcpy(data, radio->buffer + 2, len);
>> + return 0;
>> + }
>> + if (time_is_before_jiffies(until_jiffies)) {
>> + /* Zero the status value, ensuring CTS isn't set */
>> + data[0] = 0;
>> + return 0;
>> + }
>
> Again, I think that the timeout condition is wrong here.
Ditto.
I clearly couldn't quite get my head around the macro's meaning.
Regards,
Hans
--
To unsubscribe from this list: send the line "unsubscribe linux-media" in
the body of a message to majord...@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
