From: Hans Verkuil <hans.verk...@cisco.com>
Fix most checkpatch errors/warnings.
It's mostly whitespace changes, except for replacing msleep with
usleep_range and the jiffies comparison with time_is_after_jiffies().
Signed-off-by: Hans Verkuil <hans.verk...@cisco.com>
---
drivers/media/radio/si4713/radio-usb-si4713.c | 4 +-
drivers/media/radio/si4713/si4713.c | 104 +++++++++++++-------------
2 files changed, 55 insertions(+), 53 deletions(-)
diff --git a/drivers/media/radio/si4713/radio-usb-si4713.c
b/drivers/media/radio/si4713/radio-usb-si4713.c
index d978844..691e487 100644
--- a/drivers/media/radio/si4713/radio-usb-si4713.c
+++ b/drivers/media/radio/si4713/radio-usb-si4713.c
@@ -207,7 +207,7 @@ static int si4713_send_startup_command(struct
si4713_usb_device *radio)
}
if (time_is_before_jiffies(until_jiffies))
return -EIO;
- msleep(3);
+ usleep_range(3000, 5000);
}
return retval;
@@ -354,7 +354,7 @@ static int si4713_i2c_read(struct si4713_usb_device *radio,
char *data, int len)
data[0] = 0;
return 0;
}
- msleep(3);
+ usleep_range(3000, 5000);
}
}
diff --git a/drivers/media/radio/si4713/si4713.c
b/drivers/media/radio/si4713/si4713.c
index 6f28a2b..451b9c0 100644
--- a/drivers/media/radio/si4713/si4713.c
+++ b/drivers/media/radio/si4713/si4713.c
@@ -50,12 +50,12 @@ MODULE_VERSION("0.0.1");
#define DEFAULT_RDS_PS_REPEAT_COUNT 0x0003
#define DEFAULT_LIMITER_RTIME 0x1392
#define DEFAULT_LIMITER_DEV 0x102CA
-#define DEFAULT_PILOT_FREQUENCY 0x4A38
+#define DEFAULT_PILOT_FREQUENCY 0x4A38
#define DEFAULT_PILOT_DEVIATION 0x1A5E
#define DEFAULT_ACOMP_ATIME 0x0000
#define DEFAULT_ACOMP_RTIME 0xF4240L
#define DEFAULT_ACOMP_GAIN 0x0F
-#define DEFAULT_ACOMP_THRESHOLD (-0x28)
+#define DEFAULT_ACOMP_THRESHOLD (-0x28)
#define DEFAULT_MUTE 0x01
#define DEFAULT_POWER_LEVEL 88
#define DEFAULT_FREQUENCY 8800
@@ -252,8 +252,8 @@ static int si4713_send_command(struct si4713_device *sdev,
const u8 command,
if (client->irq)
return -EBUSY;
- msleep(1);
- } while (jiffies <= until_jiffies);
+ usleep_range(1000, 2000);
+ } while (time_is_after_jiffies(until_jiffies));
return -EBUSY;
}
@@ -269,9 +269,9 @@ static int si4713_read_property(struct si4713_device *sdev,
u16 prop, u32 *pv)
int err;
u8 val[SI4713_GET_PROP_NRESP];
/*
- * .First byte = 0
- * .Second byte = property's MSB
- * .Third byte = property's LSB
+ * .First byte = 0
+ * .Second byte = property's MSB
+ * .Third byte = property's LSB
*/
const u8 args[SI4713_GET_PROP_NARGS] = {
0x00,
@@ -306,11 +306,11 @@ static int si4713_write_property(struct si4713_device
*sdev, u16 prop, u16 val)
int rval;
u8 resp[SI4713_SET_PROP_NRESP];
/*
- * .First byte = 0
- * .Second byte = property's MSB
- * .Third byte = property's LSB
- * .Fourth byte = value's MSB
- * .Fifth byte = value's LSB
+ * .First byte = 0
+ * .Second byte = property's MSB
+ * .Third byte = property's LSB
+ * .Fourth byte = value's MSB
+ * .Fifth byte = value's LSB
*/
const u8 args[SI4713_SET_PROP_NARGS] = {
0x00,
@@ -352,8 +352,8 @@ static int si4713_powerup(struct si4713_device *sdev)
int err;
u8 resp[SI4713_PWUP_NRESP];
/*
- * .First byte = Enabled interrupts and boot function
- * .Second byte = Input operation mode
+ * .First byte = Enabled interrupts and boot function
+ * .Second byte = Input operation mode
*/
u8 args[SI4713_PWUP_NARGS] = {
SI4713_PWUP_GPO2OEN | SI4713_PWUP_FUNC_TX,
@@ -505,18 +505,18 @@ static int si4713_wait_stc(struct si4713_device *sdev,
const int usecs)
}
if (jiffies_to_usecs(jiffies - start_jiffies) > usecs)
return err < 0 ? err : -EIO;
- /* We sleep here for 3 ms in order to avoid flooding the device
+ /* We sleep here for 3-4 ms in order to avoid flooding the
device
* with USB requests. The si4713 USB driver was developed
* by reverse engineering the Windows USB driver. The windows
* driver also has a ~2.5 ms delay between responses. */
- msleep(3);
+ usleep_range(3000, 4000);
}
}
/*
* si4713_tx_tune_freq - Sets the state of the RF carrier and sets the tuning
- * frequency between 76 and 108 MHz in 10 kHz units and
- * steps of 50 kHz.
+ * frequency between 76 and 108 MHz in 10 kHz units and
+ * steps of 50 kHz.
* @sdev: si4713_device structure for the device we are communicating
* @frequency: desired frequency (76 - 108 MHz, unit 10 KHz, step 50 kHz)
*/
@@ -525,9 +525,9 @@ static int si4713_tx_tune_freq(struct si4713_device *sdev,
u16 frequency)
int err;
u8 val[SI4713_TXFREQ_NRESP];
/*
- * .First byte = 0
- * .Second byte = frequency's MSB
- * .Third byte = frequency's LSB
+ * .First byte = 0
+ * .Second byte = frequency's MSB
+ * .Third byte = frequency's LSB
*/
const u8 args[SI4713_TXFREQ_NARGS] = {
0x00,
@@ -555,11 +555,11 @@ static int si4713_tx_tune_freq(struct si4713_device
*sdev, u16 frequency)
/*
* si4713_tx_tune_power - Sets the RF voltage level between 88 and 120 dBuV in
- * 1 dB units. A value of 0x00 indicates off. The command
- * also sets the antenna tuning capacitance. A value of 0
- * indicates autotuning, and a value of 1 - 191 indicates
- * a manual override, which results in a tuning
- * capacitance of 0.25 pF x @antcap.
+ * 1 dB units. A value of 0x00 indicates off. The command
+ * also sets the antenna tuning capacitance. A value of 0
+ * indicates autotuning, and a value of 1 - 191 indicates
+ * a manual override, which results in a tuning
+ * capacitance of 0.25 pF x @antcap.
* @sdev: si4713_device structure for the device we are communicating
* @power: tuning power (88 - 120 dBuV, unit/step 1 dB)
* @antcap: value of antenna tuning capacitor (0 - 191)
@@ -570,10 +570,10 @@ static int si4713_tx_tune_power(struct si4713_device
*sdev, u8 power,
int err;
u8 val[SI4713_TXPWR_NRESP];
/*
- * .First byte = 0
- * .Second byte = 0
- * .Third byte = power
- * .Fourth byte = antcap
+ * .First byte = 0
+ * .Second byte = 0
+ * .Third byte = power
+ * .Fourth byte = antcap
*/
u8 args[SI4713_TXPWR_NARGS] = {
0x00,
@@ -602,12 +602,12 @@ static int si4713_tx_tune_power(struct si4713_device
*sdev, u8 power,
/*
* si4713_tx_tune_measure - Enters receive mode and measures the received noise
- * level in units of dBuV on the selected frequency.
- * The Frequency must be between 76 and 108 MHz in 10 kHz
- * units and steps of 50 kHz. The command also sets the
- * antenna tuning capacitance. A value of 0 means
- * autotuning, and a value of 1 to 191 indicates manual
- * override.
+ * level in units of dBuV on the selected frequency.
+ * The Frequency must be between 76 and 108 MHz in 10 kHz
+ * units and steps of 50 kHz. The command also sets the
+ * antenna tuning capacitance. A value of 0 means
+ * autotuning, and a value of 1 to 191 indicates manual
+ * override.
* @sdev: si4713_device structure for the device we are communicating
* @frequency: desired frequency (76 - 108 MHz, unit 10 KHz, step 50 kHz)
* @antcap: value of antenna tuning capacitor (0 - 191)
@@ -618,10 +618,10 @@ static int si4713_tx_tune_measure(struct si4713_device
*sdev, u16 frequency,
int err;
u8 val[SI4713_TXMEA_NRESP];
/*
- * .First byte = 0
- * .Second byte = frequency's MSB
- * .Third byte = frequency's LSB
- * .Fourth byte = antcap
+ * .First byte = 0
+ * .Second byte = frequency's MSB
+ * .Third byte = frequency's LSB
+ * .Fourth byte = antcap
*/
const u8 args[SI4713_TXMEA_NARGS] = {
0x00,
@@ -651,11 +651,11 @@ static int si4713_tx_tune_measure(struct si4713_device
*sdev, u16 frequency,
/*
* si4713_tx_tune_status- Returns the status of the tx_tune_freq, tx_tune_mea
or
- * tx_tune_power commands. This command return the current
- * frequency, output voltage in dBuV, the antenna tunning
- * capacitance value and the received noise level. The
- * command also clears the stcint interrupt bit when the
- * first bit of its arguments is high.
+ * tx_tune_power commands. This command return the current
+ * frequency, output voltage in dBuV, the antenna tunning
+ * capacitance value and the received noise level. The
+ * command also clears the stcint interrupt bit when the
+ * first bit of its arguments is high.
* @sdev: si4713_device structure for the device we are communicating
* @intack: 0x01 to clear the seek/tune complete interrupt status indicator.
* @frequency: returned frequency
@@ -670,7 +670,7 @@ static int si4713_tx_tune_status(struct si4713_device
*sdev, u8 intack,
int err;
u8 val[SI4713_TXSTATUS_NRESP];
/*
- * .First byte = intack bit
+ * .First byte = intack bit
*/
const u8 args[SI4713_TXSTATUS_NARGS] = {
intack & SI4713_INTACK_MASK,
@@ -1364,7 +1364,7 @@ static int si4713_probe(struct i2c_client *client,
struct v4l2_ctrl_handler *hdl;
int rval, i;
- sdev = kzalloc(sizeof *sdev, GFP_KERNEL);
+ sdev = kzalloc(sizeof(*sdev), GFP_KERNEL);
if (!sdev) {
dev_err(&client->dev, "Failed to alloc video device.\n");
rval = -ENOMEM;
@@ -1440,8 +1440,8 @@ static int si4713_probe(struct i2c_client *client,
V4L2_CID_AUDIO_COMPRESSION_GAIN, 0, MAX_ACOMP_GAIN, 1,
DEFAULT_ACOMP_GAIN);
sdev->compression_threshold = v4l2_ctrl_new_std(hdl, &si4713_ctrl_ops,
- V4L2_CID_AUDIO_COMPRESSION_THRESHOLD,
MIN_ACOMP_THRESHOLD,
- MAX_ACOMP_THRESHOLD, 1,
+ V4L2_CID_AUDIO_COMPRESSION_THRESHOLD,
+ MIN_ACOMP_THRESHOLD, MAX_ACOMP_THRESHOLD, 1,
DEFAULT_ACOMP_THRESHOLD);
sdev->compression_attack_time = v4l2_ctrl_new_std(hdl, &si4713_ctrl_ops,
V4L2_CID_AUDIO_COMPRESSION_ATTACK_TIME, 0,
@@ -1463,9 +1463,11 @@ static int si4713_probe(struct i2c_client *client,
V4L2_CID_TUNE_PREEMPHASIS,
V4L2_PREEMPHASIS_75_uS, 0, V4L2_PREEMPHASIS_50_uS);
sdev->tune_pwr_level = v4l2_ctrl_new_std(hdl, &si4713_ctrl_ops,
- V4L2_CID_TUNE_POWER_LEVEL, 0, SI4713_MAX_POWER, 1,
DEFAULT_POWER_LEVEL);
+ V4L2_CID_TUNE_POWER_LEVEL, 0, SI4713_MAX_POWER,
+ 1, DEFAULT_POWER_LEVEL);
sdev->tune_ant_cap = v4l2_ctrl_new_std(hdl, &si4713_ctrl_ops,
- V4L2_CID_TUNE_ANTENNA_CAPACITOR, 0, SI4713_MAX_ANTCAP,
1, 0);
+ V4L2_CID_TUNE_ANTENNA_CAPACITOR, 0, SI4713_MAX_ANTCAP,
+ 1, 0);
if (hdl->error) {
rval = hdl->error;
--
1.8.4.rc3
--
To unsubscribe from this list: send the line "unsubscribe linux-media" in
the body of a message to majord...@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
