Acked-by: Hugues Fruchet <hugues.fruc...@st.com>
Tested successfully on STM324x9I-EVAL evaluation board embedding
an OV2640 camera sensor.
I don't understand the comment around s_power op that has been dropped
(it is there in code), and no problem is observed doing several
open/close, tell me if I miss something.
BR,
Hugues.
On 03/28/2017 10:23 AM, Hans Verkuil wrote:
> From: Hans Verkuil <hans.verk...@cisco.com>
>
> Convert ov2640 to a standard subdev driver. The soc-camera driver no longer
> uses this driver, so it can safely be converted.
>
> Note: the s_power op has been dropped: this never worked. When the last open()
> is closed, then the power is turned off, and when it is opened again the power
> is turned on again, but the old state isn't restored.
>
> Someone else can figure out in the future how to get this working correctly,
> but I don't want to spend more time on this.
>
> Signed-off-by: Hans Verkuil <hans.verk...@cisco.com>
> Acked-by: Sakari Ailus <sakari.ai...@linux.intel.com>
> ---
> drivers/media/i2c/Kconfig | 11 ++++
> drivers/media/i2c/Makefile | 1 +
> drivers/media/i2c/{soc_camera => }/ov2640.c | 89
> +++++------------------------
> drivers/media/i2c/soc_camera/Kconfig | 6 --
> drivers/media/i2c/soc_camera/Makefile | 1 -
> 5 files changed, 27 insertions(+), 81 deletions(-)
> rename drivers/media/i2c/{soc_camera => }/ov2640.c (94%)
>
> diff --git a/drivers/media/i2c/Kconfig b/drivers/media/i2c/Kconfig
> index cee1dae6e014..db2c63f592c5 100644
> --- a/drivers/media/i2c/Kconfig
> +++ b/drivers/media/i2c/Kconfig
> @@ -520,6 +520,17 @@ config VIDEO_APTINA_PLL
> config VIDEO_SMIAPP_PLL
> tristate
>
> +config VIDEO_OV2640
> + tristate "OmniVision OV2640 sensor support"
> + depends on VIDEO_V4L2 && I2C && GPIOLIB
> + depends on MEDIA_CAMERA_SUPPORT
> + help
> + This is a Video4Linux2 sensor-level driver for the OmniVision
> + OV2640 camera.
> +
> + To compile this driver as a module, choose M here: the
> + module will be called ov2640.
> +
> config VIDEO_OV2659
> tristate "OmniVision OV2659 sensor support"
> depends on VIDEO_V4L2 && I2C
> diff --git a/drivers/media/i2c/Makefile b/drivers/media/i2c/Makefile
> index 5bc7bbeb5499..50af1e11c85a 100644
> --- a/drivers/media/i2c/Makefile
> +++ b/drivers/media/i2c/Makefile
> @@ -57,6 +57,7 @@ obj-$(CONFIG_VIDEO_VP27SMPX) += vp27smpx.o
> obj-$(CONFIG_VIDEO_SONY_BTF_MPX) += sony-btf-mpx.o
> obj-$(CONFIG_VIDEO_UPD64031A) += upd64031a.o
> obj-$(CONFIG_VIDEO_UPD64083) += upd64083.o
> +obj-$(CONFIG_VIDEO_OV2640) += ov2640.o
> obj-$(CONFIG_VIDEO_OV7640) += ov7640.o
> obj-$(CONFIG_VIDEO_OV7670) += ov7670.o
> obj-$(CONFIG_VIDEO_OV9650) += ov9650.o
> diff --git a/drivers/media/i2c/soc_camera/ov2640.c
> b/drivers/media/i2c/ov2640.c
> similarity index 94%
> rename from drivers/media/i2c/soc_camera/ov2640.c
> rename to drivers/media/i2c/ov2640.c
> index b9a0069f5b33..83f88efbce69 100644
> --- a/drivers/media/i2c/soc_camera/ov2640.c
> +++ b/drivers/media/i2c/ov2640.c
> @@ -24,8 +24,8 @@
> #include <linux/v4l2-mediabus.h>
> #include <linux/videodev2.h>
>
> -#include <media/soc_camera.h>
> #include <media/v4l2-clk.h>
> +#include <media/v4l2-device.h>
> #include <media/v4l2-subdev.h>
> #include <media/v4l2-ctrls.h>
> #include <media/v4l2-image-sizes.h>
> @@ -287,7 +287,6 @@ struct ov2640_priv {
> struct v4l2_clk *clk;
> const struct ov2640_win_size *win;
>
> - struct soc_camera_subdev_desc ssdd_dt;
> struct gpio_desc *resetb_gpio;
> struct gpio_desc *pwdn_gpio;
> };
> @@ -677,13 +676,8 @@ static int ov2640_reset(struct i2c_client *client)
> }
>
> /*
> - * soc_camera_ops functions
> + * functions
> */
> -static int ov2640_s_stream(struct v4l2_subdev *sd, int enable)
> -{
> - return 0;
> -}
> -
> static int ov2640_s_ctrl(struct v4l2_ctrl *ctrl)
> {
> struct v4l2_subdev *sd =
> @@ -744,10 +738,16 @@ static int ov2640_s_register(struct v4l2_subdev *sd,
> static int ov2640_s_power(struct v4l2_subdev *sd, int on)
> {
> struct i2c_client *client = v4l2_get_subdevdata(sd);
> - struct soc_camera_subdev_desc *ssdd = soc_camera_i2c_to_desc(client);
> struct ov2640_priv *priv = to_ov2640(client);
>
> - return soc_camera_set_power(&client->dev, ssdd, priv->clk, on);
> + gpiod_direction_output(priv->pwdn_gpio, !on);
> + if (on && priv->resetb_gpio) {
> + /* Active the resetb pin to perform a reset pulse */
> + gpiod_direction_output(priv->resetb_gpio, 1);
> + usleep_range(3000, 5000);
> + gpiod_direction_output(priv->resetb_gpio, 0);
> + }
> + return 0;
> }
>
> /* Select the nearest higher resolution for capture */
> @@ -994,26 +994,6 @@ static struct v4l2_subdev_core_ops
> ov2640_subdev_core_ops = {
> .s_power = ov2640_s_power,
> };
>
> -static int ov2640_g_mbus_config(struct v4l2_subdev *sd,
> - struct v4l2_mbus_config *cfg)
> -{
> - struct i2c_client *client = v4l2_get_subdevdata(sd);
> - struct soc_camera_subdev_desc *ssdd = soc_camera_i2c_to_desc(client);
> -
> - cfg->flags = V4L2_MBUS_PCLK_SAMPLE_RISING | V4L2_MBUS_MASTER |
> - V4L2_MBUS_VSYNC_ACTIVE_HIGH | V4L2_MBUS_HSYNC_ACTIVE_HIGH |
> - V4L2_MBUS_DATA_ACTIVE_HIGH;
> - cfg->type = V4L2_MBUS_PARALLEL;
> - cfg->flags = soc_camera_apply_board_flags(ssdd, cfg);
> -
> - return 0;
> -}
> -
> -static struct v4l2_subdev_video_ops ov2640_subdev_video_ops = {
> - .s_stream = ov2640_s_stream,
> - .g_mbus_config = ov2640_g_mbus_config,
> -};
> -
> static const struct v4l2_subdev_pad_ops ov2640_subdev_pad_ops = {
> .enum_mbus_code = ov2640_enum_mbus_code,
> .get_selection = ov2640_get_selection,
> @@ -1023,40 +1003,9 @@ static const struct v4l2_subdev_pad_ops
> ov2640_subdev_pad_ops = {
>
> static struct v4l2_subdev_ops ov2640_subdev_ops = {
> .core = &ov2640_subdev_core_ops,
> - .video = &ov2640_subdev_video_ops,
> .pad = &ov2640_subdev_pad_ops,
> };
>
> -/* OF probe functions */
> -static int ov2640_hw_power(struct device *dev, int on)
> -{
> - struct i2c_client *client = to_i2c_client(dev);
> - struct ov2640_priv *priv = to_ov2640(client);
> -
> - dev_dbg(&client->dev, "%s: %s the camera\n",
> - __func__, on ? "ENABLE" : "DISABLE");
> -
> - if (priv->pwdn_gpio)
> - gpiod_direction_output(priv->pwdn_gpio, !on);
> -
> - return 0;
> -}
> -
> -static int ov2640_hw_reset(struct device *dev)
> -{
> - struct i2c_client *client = to_i2c_client(dev);
> - struct ov2640_priv *priv = to_ov2640(client);
> -
> - if (priv->resetb_gpio) {
> - /* Active the resetb pin to perform a reset pulse */
> - gpiod_direction_output(priv->resetb_gpio, 1);
> - usleep_range(3000, 5000);
> - gpiod_direction_output(priv->resetb_gpio, 0);
> - }
> -
> - return 0;
> -}
> -
> static int ov2640_probe_dt(struct i2c_client *client,
> struct ov2640_priv *priv)
> {
> @@ -1076,11 +1025,6 @@ static int ov2640_probe_dt(struct i2c_client *client,
> else if (IS_ERR(priv->pwdn_gpio))
> return PTR_ERR(priv->pwdn_gpio);
>
> - /* Initialize the soc_camera_subdev_desc */
> - priv->ssdd_dt.power = ov2640_hw_power;
> - priv->ssdd_dt.reset = ov2640_hw_reset;
> - client->dev.platform_data = &priv->ssdd_dt;
> -
> return 0;
> }
>
> @@ -1091,7 +1035,6 @@ static int ov2640_probe(struct i2c_client *client,
> const struct i2c_device_id *did)
> {
> struct ov2640_priv *priv;
> - struct soc_camera_subdev_desc *ssdd = soc_camera_i2c_to_desc(client);
> struct i2c_adapter *adapter = to_i2c_adapter(client->dev.parent);
> int ret;
>
> @@ -1112,17 +1055,15 @@ static int ov2640_probe(struct i2c_client *client,
> if (IS_ERR(priv->clk))
> return -EPROBE_DEFER;
>
> - if (!ssdd && !client->dev.of_node) {
> + if (!client->dev.of_node) {
> dev_err(&client->dev, "Missing platform_data for driver\n");
> ret = -EINVAL;
> goto err_clk;
> }
>
> - if (!ssdd) {
> - ret = ov2640_probe_dt(client, priv);
> - if (ret)
> - goto err_clk;
> - }
> + ret = ov2640_probe_dt(client, priv);
> + if (ret)
> + goto err_clk;
>
> v4l2_i2c_subdev_init(&priv->subdev, client, &ov2640_subdev_ops);
> v4l2_ctrl_handler_init(&priv->hdl, 2);
> @@ -1190,6 +1131,6 @@ static struct i2c_driver ov2640_i2c_driver = {
>
> module_i2c_driver(ov2640_i2c_driver);
>
> -MODULE_DESCRIPTION("SoC Camera driver for Omni Vision 2640 sensor");
> +MODULE_DESCRIPTION("Driver for Omni Vision 2640 sensor");
> MODULE_AUTHOR("Alberto Panizzo");
> MODULE_LICENSE("GPL v2");
> diff --git a/drivers/media/i2c/soc_camera/Kconfig
> b/drivers/media/i2c/soc_camera/Kconfig
> index 7704bcf5cc25..96859f37cb1c 100644
> --- a/drivers/media/i2c/soc_camera/Kconfig
> +++ b/drivers/media/i2c/soc_camera/Kconfig
> @@ -41,12 +41,6 @@ config SOC_CAMERA_MT9V022
> help
> This driver supports MT9V022 cameras from Micron
>
> -config SOC_CAMERA_OV2640
> - tristate "ov2640 camera support"
> - depends on SOC_CAMERA && I2C
> - help
> - This is a ov2640 camera driver
> -
> config SOC_CAMERA_OV5642
> tristate "ov5642 camera support"
> depends on SOC_CAMERA && I2C
> diff --git a/drivers/media/i2c/soc_camera/Makefile
> b/drivers/media/i2c/soc_camera/Makefile
> index 6f994f9353a0..974bdb721dbe 100644
> --- a/drivers/media/i2c/soc_camera/Makefile
> +++ b/drivers/media/i2c/soc_camera/Makefile
> @@ -3,7 +3,6 @@ obj-$(CONFIG_SOC_CAMERA_MT9M001) += mt9m001.o
> obj-$(CONFIG_SOC_CAMERA_MT9T031) += mt9t031.o
> obj-$(CONFIG_SOC_CAMERA_MT9T112) += mt9t112.o
> obj-$(CONFIG_SOC_CAMERA_MT9V022) += mt9v022.o
> -obj-$(CONFIG_SOC_CAMERA_OV2640) += ov2640.o
> obj-$(CONFIG_SOC_CAMERA_OV5642) += ov5642.o
> obj-$(CONFIG_SOC_CAMERA_OV6650) += ov6650.o
> obj-$(CONFIG_SOC_CAMERA_OV772X) += ov772x.o
>
