There are various issues with the examples in this documentation, some of the DT labels are invalid and one of the macro THERMAL_NO_LIMITS referenced is not available as well.
As Its highly likely that people would pick some samples from the documentation, I though fixing these would be best rather than giving starter a challenge to figure out whats going wrong with examples. This patch attempts to fix such errors in the documentation. Signed-off-by: Srinivas Kandagatla <[email protected]> --- .../devicetree/bindings/thermal/thermal.txt | 44 +++++++++++----------- 1 file changed, 22 insertions(+), 22 deletions(-) diff --git a/Documentation/devicetree/bindings/thermal/thermal.txt b/Documentation/devicetree/bindings/thermal/thermal.txt index f5db6b7..97ed14e 100644 --- a/Documentation/devicetree/bindings/thermal/thermal.txt +++ b/Documentation/devicetree/bindings/thermal/thermal.txt @@ -251,24 +251,24 @@ ocp { }; thermal-zones { - cpu-thermal: cpu-thermal { + cpu_thermal: cpu-thermal { polling-delay-passive = <250>; /* milliseconds */ polling-delay = <1000>; /* milliseconds */ thermal-sensors = <&bandgap0>; trips { - cpu-alert0: cpu-alert { + cpu_alert0: cpu-alert0 { temperature = <90000>; /* millicelsius */ hysteresis = <2000>; /* millicelsius */ type = "active"; }; - cpu-alert1: cpu-alert { + cpu_alert1: cpu-alert1 { temperature = <100000>; /* millicelsius */ hysteresis = <2000>; /* millicelsius */ type = "passive"; }; - cpu-crit: cpu-crit { + cpu_crit: cpu-crit { temperature = <125000>; /* millicelsius */ hysteresis = <2000>; /* millicelsius */ type = "critical"; @@ -277,17 +277,17 @@ thermal-zones { cooling-maps { map0 { - trip = <&cpu-alert0>; - cooling-device = <&fan0 THERMAL_NO_LIMITS 4>; + trip = <&cpu_alert0>; + cooling-device = <&fan0 THERMAL_NO_LIMIT 4>; }; map1 { - trip = <&cpu-alert1>; - cooling-device = <&fan0 5 THERMAL_NO_LIMITS>; + trip = <&cpu_alert1>; + cooling-device = <&fan0 5 THERMAL_NO_LIMIT>; }; map2 { - trip = <&cpu-alert1>; + trip = <&cpu_alert1>; cooling-device = - <&cpu0 THERMAL_NO_LIMITS THERMAL_NO_LIMITS>; + <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; }; }; }; @@ -298,13 +298,13 @@ used to monitor the zone 'cpu-thermal' using its sole sensor. A fan device (fan0) is controlled via I2C bus 1, at address 0x48, and has ten different cooling states 0-9. It is used to remove the heat out of the thermal zone 'cpu-thermal' using its cooling states -from its minimum to 4, when it reaches trip point 'cpu-alert0' +from its minimum to 4, when it reaches trip point 'cpu_alert0' at 90C, as an example of active cooling. The same cooling device is used at -'cpu-alert1', but from 5 to its maximum state. The cpu@0 device is also +'cpu_alert1', but from 5 to its maximum state. The cpu@0 device is also linked to the same thermal zone, 'cpu-thermal', as a passive cooling device, -using all its cooling states at trip point 'cpu-alert1', +using all its cooling states at trip point 'cpu_alert1', which is a trip point at 100C. On the thermal zone 'cpu-thermal', at the -temperature of 125C, represented by the trip point 'cpu-crit', the silicon +temperature of 125C, represented by the trip point 'cpu_crit', the silicon is not reliable anymore. (b) - IC with several internal sensors @@ -329,7 +329,7 @@ ocp { }; thermal-zones { - cpu-thermal: cpu-thermal { + cpu_thermal: cpu-thermal { polling-delay-passive = <250>; /* milliseconds */ polling-delay = <1000>; /* milliseconds */ @@ -338,12 +338,12 @@ thermal-zones { trips { /* each zone within the SoC may have its own trips */ - cpu-alert: cpu-alert { + cpu_alert: cpu-alert { temperature = <100000>; /* millicelsius */ hysteresis = <2000>; /* millicelsius */ type = "passive"; }; - cpu-crit: cpu-crit { + cpu_crit: cpu-crit { temperature = <125000>; /* millicelsius */ hysteresis = <2000>; /* millicelsius */ type = "critical"; @@ -365,12 +365,12 @@ thermal-zones { trips { /* each zone within the SoC may have its own trips */ - gpu-alert: gpu-alert { + gpu_alert: gpu-alert { temperature = <90000>; /* millicelsius */ hysteresis = <2000>; /* millicelsius */ type = "passive"; }; - gpu-crit: gpu-crit { + gpu_crit: gpu-crit { temperature = <105000>; /* millicelsius */ hysteresis = <2000>; /* millicelsius */ type = "critical"; @@ -392,12 +392,12 @@ thermal-zones { trips { /* each zone within the SoC may have its own trips */ - dsp-alert: gpu-alert { + dsp_alert: gpu-alert { temperature = <90000>; /* millicelsius */ hysteresis = <2000>; /* millicelsius */ type = "passive"; }; - dsp-crit: gpu-crit { + dsp_crit: gpu-crit { temperature = <135000>; /* millicelsius */ hysteresis = <2000>; /* millicelsius */ type = "critical"; @@ -457,7 +457,7 @@ ocp { }; thermal-zones { - cpu-thermal: cpu-thermal { + cpu_thermal: cpu-thermal { polling-delay-passive = <250>; /* milliseconds */ polling-delay = <1000>; /* milliseconds */ -- 1.9.1 -- To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to [email protected] More majordomo info at http://vger.kernel.org/majordomo-info.html Please read the FAQ at http://www.tux.org/lkml/
