Hi, I am setting hw.usb.ehci.no_hs: 0 -> 1. After that I connect my iPad. Speed still remains at HIGH according to usbconfig.
"ugen1.1: <EHCI root HUB Intel> at usbus1, cfg=0 md=HOST spd=HIGH (480Mbps) pwr=SAVE (0mA) ugen0.1: <EHCI root HUB Intel> at usbus0, cfg=0 md=HOST spd=HIGH (480Mbps) pwr=SAVE (0mA) ugen1.2: <product 0x0020 vendor 0x8087> at usbus1, cfg=0 md=HOST spd=HIGH (480Mbps) pwr=SAVE (0mA) ugen0.2: <product 0x0020 vendor 0x8087> at usbus0, cfg=0 md=HOST spd=HIGH (480Mbps) pwr=SAVE (0mA) ugen1.3: <Mass Storage Device Generic> at usbus1, cfg=0 md=HOST spd=HIGH (480Mbps) pwr=ON (250mA) ugen0.4: <USB-PS2 Optical Mouse Logitech> at usbus0, cfg=0 md=HOST spd=LOW (1.5Mbps) pwr=ON (98mA) ugen0.3: <iPad Apple Inc.> at usbus0, cfg=0 md=HOST spd=HIGH (480Mbps) pwr=ON (500mA)" After issuing "usbconfig -d 0.1 reset" usbconfig shows this output and I have to reboot to get my mouse back: "ugen1.1: <EHCI root HUB Intel> at usbus1, cfg=0 md=HOST spd=HIGH (480Mbps) pwr=SAVE (0mA) ugen0.1: <EHCI root HUB Intel> at usbus0, cfg=0 md=HOST spd=HIGH (480Mbps) pwr=SAVE (0mA) ugen1.2: <product 0x0020 vendor 0x8087> at usbus1, cfg=0 md=HOST spd=HIGH (480Mbps) pwr=SAVE (0mA) ugen1.3: <Mass Storage Device Generic> at usbus1, cfg=0 md=HOST spd=HIGH (480Mbps) pwr=ON (250mA)" Jurgen -----Original-Nachricht----- Betreff: Re: USB Virtualbox Datum: Thu, 14 May 2015 08:54:38 +0200 Von: Hans Petter Selasky <[email protected]> An: "[email protected]" <[email protected]>, "[email protected]" <[email protected]> On 05/14/15 08:27, [email protected] wrote: > Hi, > > I believe this is the relevant output of pciconf for the usb controllers: > > "ehci0@pci0:0:26:0: class=0x0c0320 card=0x75811462 chip=0x3b3c8086 rev=0x05 > hdr=0x00 > vendor = 'Intel Corporation' > device = '5 Series/3400 Series Chipset USB2 Enhanced Host Controller' > class = serial bus > subclass = USB > > ehci1@pci0:0:29:0: class=0x0c0320 card=0x75811462 chip=0x3b348086 rev=0x05 > hdr=0x00 > vendor = 'Intel Corporation' > device = '5 Series/3400 Series Chipset USB2 Enhanced Host Controller' > class = serial bus > subclass = USB" > > It is a MSI P55-GD80 mainboard. The usb 2 devices are available in the > virtualbox usb menu but not useable in windows. > > Thanks for your help. > Jurgen > > -----Original-Nachricht----- > Betreff: Re: USB Virtualbox > Datum: Thu, 14 May 2015 07:50:03 +0200 > Von: Hans Petter Selasky <[email protected]> > An: "[email protected]" <[email protected]>, [email protected] > > On 05/13/15 17:05, [email protected] wrote: >> Hi everyone, >> >> I try to get my iPad recognized with a Windows 7 guest and Virtualbox under >> freebsd 10 host. >> >> Because there is no usb 2.0 support for freebsd-virtualbox I try to force it >> to usb 1. >> >> I am using "sysctl hw.usb.ehci.no_hs=1" as mentioned here >> http://www.clearchain.com/blog/posts/how-to-use-freebsd-virtualbox-and-usb2-0-devices >> >> But even after disconnecting and reconnecting iPad is still is at usb 2.0 >> speed. >> >> Is there another way to use usb devices in Virtualbox? >> > > Hi, > > Can you show what USB controllers are present. If you have XHCI, you > need to set the port routing mask and the no_hs sysctls at the same time. > > --HPS > Hi, "no_hs" must be set before plugging the device, or you need to reset the parent HUB using "usbconfig -d X.1 reset" after setting this variable. Can you show output from usbconfig ? --HPS _______________________________________________ [email protected] mailing list http://lists.freebsd.org/mailman/listinfo/freebsd-usb To unsubscribe, send any mail to "[email protected]"
