I searched the mailing list archives and didn't find anything that looks like this, so maybe it's just me, but adding ppbus and lpt0 to my kernel config (sources cvsupped on 4/17) causes my machine to hang hard during boot. The freeze occurs shortly after probing my network card and is accompanied (sometimes) with an error like
RTC BIOS diagnostic error ff<clock_battery,ROM_cksum,config_unit,memory_size,fixed_disk,invalid_time> My config looks like (if I comment out the ppc,ppbus, and lpt lines, the kernel works fine): machine "i386" cpu "I586_CPU" cpu "I686_CPU" ident GENERIC maxusers 64 #makeoptions DEBUG="-g" #Build kernel with gdb(1) debug symbols options MATH_EMULATE #Support for x87 emulation options INET #InterNETworking options FFS #Berkeley Fast Filesystem options FFS_ROOT #FFS usable as root device [keep this!] options MFS #Memory Filesystem options MFS_ROOT #MFS usable as root device, "MFS" req'ed #options NFS #Network Filesystem #options NFS_ROOT #NFS usable as root device, "NFS " req'ed options MSDOSFS #MSDOS Filesystem options "CD9660" #ISO 9660 Filesystem options "CD9660_ROOT" #CD-ROM usable as root. "CD9660" req'ed options PROCFS #Process filesystem options "COMPAT_43" #Compatible with BSD 4.3 [KEEP THIS!] options SCSI_DELAY=5000 #Be pessimistic about Joe SCSI device options UCONSOLE #Allow users to grab the console options FAILSAFE #Be conservative options USERCONFIG #boot -c editor options VISUAL_USERCONFIG #visual boot -c editor config kernel root on da0 # To make an SMP kernel, the next two are needed #options SMP # Symmetric MultiProcessor Kernel #options APIC_IO # Symmetric (APIC) I/O # Optionally these may need tweaked, (defaults shown): #options NCPU=2 # number of CPUs #options NBUS=4 # number of busses #options NAPIC=1 # number of IO APICs #options NINTR=24 # number of INTs controller isa0 at nexus? #controller pnp0 # PnP support for ISA #controller eisa0 controller pci0 at nexus? controller fdc0 at isa? port "IO_FD1" bio irq 6 drq 2 disk fd0 at fdc0 drive 0 controller wdc0 at isa? port "IO_WD1" bio irq 14 disk wd0 at wdc0 drive 0 disk wd1 at wdc0 drive 1 controller wdc1 at isa? port "IO_WD2" bio irq 15 disk wd device wcd0 #IDE CD-ROM device wfd0 #IDE Floppy (e.g. LS-120) # A single entry for any of these controllers (ncr, ahb, ahc) is # sufficient for any number of installed devices. controller ncr0 controller ahc0 controller scbus0 device da0 device sa0 device pass0 device cd0 #Only need one of these, the code dynamically grows # atkbdc0 controlls both the keyboard and the PS/2 mouse controller atkbdc0 at isa? port IO_KBD device atkbd0 at atkbdc? tty irq 1 device psm0 at atkbdc? tty irq 12 device vga0 at isa? port ? conflicts # splash screen/screen saver #pseudo-device splash # syscons is the default console driver, resembling an SCO console device sc0 at isa? tty # Enable this and PCVT_FREEBSD for pcvt vt220 compatible console driver #device vt0 at isa? tty #options XSERVER # support for X server #options FAT_CURSOR # start with block cursor # If you have a ThinkPAD, uncomment this along with the rest of the PCVT lines #options PCVT_SCANSET=2 # IBM keyboards are non-std device npx0 at nexus? port IO_NPX irq 13 # # Laptop support (see LINT for more options) # #device apm0 at nexus? disable flags 0x31 # Advanced Power Management device sio0 at isa? port "IO_COM1" flags 0x10 tty irq 4 device sio1 at isa? port "IO_COM2" tty irq 3 device sio2 at isa? disable port "IO_COM3" tty irq 5 device sio3 at isa? disable port "IO_COM4" tty irq 9 # Parallel port device ppc0 at isa? port? tty irq 7 controller ppbus0 device lpt0 at ppbus? #device plip0 at ppbus? #device ppi0 at ppbus? #controller vpo0 at ppbus? # # The following Ethernet NICs are all PCI devices. # device de0 # DEC/Intel DC21x4x (``Tulip'') pseudo-device loop pseudo-device ether pseudo-device sl 1 pseudo-device ppp 1 pseudo-device tun 1 pseudo-device pty 16 pseudo-device gzip # Exec gzipped a.out's # KTRACE enables the system-call tracing facility ktrace(2). # This adds 4 KB bloat to your kernel, and slightly increases # the costs of each syscall. options KTRACE #kernel tracing # This provides support for System V shared memory and message queues. # options SYSVSHM options SYSVMSG options SYSVSEM # The `bpfilter' pseudo-device enables the Berkeley Packet Filter. Be # aware of the legal and administrative consequences of enabling this # option. The number of devices determines the maximum number of # simultaneous BPF clients programs runnable. #pseudo-device bpfilter 4 #Berkeley packet filter # USB support #controller uhci0 #controller ohci0 #controller usb0 # # for the moment we have to specify the priorities of the device # drivers explicitly by the ordering in the list below. This will # be changed in the future. # #device ums0 #device ukbd0 #device ulpt0 #device uhid0 #device ugen0 Anyone have any advice? Eric Jones To Unsubscribe: send mail to majord...@freebsd.org with "unsubscribe freebsd-current" in the body of the message