On Tue, 30 Jan 2007 19:39:20 +0000 (GMT)
Dave Airlie <[EMAIL PROTECTED]> wrote:
>
> > 06:00.0 VGA compatible controller: ATI Technologies Inc RV370 5B60 [Radeon
> > X300 (PCIE)] (prog-if 00 [VGA])
> > Subsystem: VISIONTEK Unknown device 0401
> > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
> > Stepping- SERR- FastB2B-
> > Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
> > <MAbort- >SERR- <PERR-
> > Latency: 0, Cache Line Size: 16 bytes
> > Interrupt: pin A routed to IRQ 16
> > Region 0: Memory at e0000000 (32-bit, prefetchable) [size=128M]
> > Region 1: I/O ports at c800 [size=256]
> > Region 2: Memory at ff9f0000 (32-bit, non-prefetchable) [size=64K]
> > Expansion ROM at ff9c0000 [disabled] [size=128K]
> > Capabilities: <access denied>
> > 00: 02 10 60 5b 07 00 10 00 00 00 00 03 04 00 80 00
> > 10: 08 00 00 e0 01 c8 00 00 00 00 9f ff 00 00 00 00
> > 20: 00 00 00 00 00 00 00 00 00 00 00 00 45 15 01 04
> > 30: 00 00 9c ff 50 00 00 00 00 00 00 00 0a 01 00 00
>
>
> Does it always put the PCI stuff into the top 1GB address range, where
> does the final 1GB of memory go? or does lspci look diffferent with 4GBs
> in?
>
> Dave.
Here is the lspci output both with the mapped (4G) and non-mapped (3G)
BIOS option.
--
Stephen Hemminger <[EMAIL PROTECTED]>
00:00.0 Host bridge: Intel Corporation 975X Express Memory Controller Hub (rev
c0)
Subsystem: ASUSTeK Computer Inc. Unknown device 8178
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort+ >SERR- <PERR-
Latency: 0
Capabilities: [e0] Vendor Specific Information
00: 86 80 7c 27 06 00 90 20 c0 00 00 06 00 00 00 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 43 10 78 81
30: 00 00 00 00 e0 00 00 00 00 00 00 00 00 00 00 00
00:01.0 PCI bridge: Intel Corporation 975X Express PCI Express Root Port (rev
c0) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 16 bytes
Bus: primary=00, secondary=06, subordinate=06, sec-latency=0
I/O behind bridge: 0000c000-0000cfff
Memory behind bridge: ff900000-ff9fffff
Prefetchable memory behind bridge: 00000000dff00000-00000000efe00000
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA+ MAbort- >Reset- FastB2B-
Capabilities: [88] #0d [0000]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [90] Message Signalled Interrupts: 64bit- Queue=0/0
Enable+
Address: fee00000 Data: 40c9
Capabilities: [a0] Express Root Port (Slot+) IRQ 0
Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s <64ns, L1 <1us
Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
Link: Supported Speed 2.5Gb/s, Width x16, ASPM L0s, Port 2
Link: Latency L0s <256ns, L1 <4us
Link: ASPM Disabled RCB 64 bytes CommClk+ ExtSynch-
Link: Speed 2.5Gb/s, Width x16
Slot: AtnBtn- PwrCtrl- MRL- AtnInd- PwrInd- HotPlug- Surpise-
Slot: Number 0, PowerLimit 75.000000
Slot: Enabled AtnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq-
Slot: AttnInd Off, PwrInd On, Power-
Root: Correctable- Non-Fatal- Fatal- PME-
00: 86 80 7d 27 07 05 10 00 c0 00 04 06 04 00 01 00
10: 00 00 00 00 00 00 00 00 00 06 06 00 c0 c0 00 00
20: 90 ff 90 ff f1 df e1 ef 00 00 00 00 00 00 00 00
30: 00 00 00 00 88 00 00 00 00 00 00 00 0a 01 0a 00
00:1b.0 Audio device: Intel Corporation 82801G (ICH7 Family) High Definition
Audio Controller (rev 01)
Subsystem: ASUSTeK Computer Inc. Unknown device 81d8
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 16 bytes
Interrupt: pin A routed to IRQ 185
Region 0: Memory at ffafc000 (64-bit, non-prefetchable) [size=16K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=55mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [60] Message Signalled Interrupts: 64bit+ Queue=0/0
Enable-
Address: 0000000000000000 Data: 0000
Capabilities: [70] Express Unknown type IRQ 0
Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s <64ns, L1 <1us
Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+
Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
Link: Supported Speed unknown, Width x0, ASPM unknown, Port 0
Link: Latency L0s <64ns, L1 <1us
Link: ASPM Disabled CommClk- ExtSynch-
Link: Speed unknown, Width x0
00: 86 80 d8 27 06 00 10 00 01 00 03 04 04 00 00 00
10: 04 c0 af ff 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 43 10 d8 81
30: 00 00 00 00 50 00 00 00 00 00 00 00 0b 01 00 00
00:1c.0 PCI bridge: Intel Corporation 82801G (ICH7 Family) PCI Express Port 1
(rev 01) (prog-if 00 [Normal decode])
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 16 bytes
Bus: primary=00, secondary=05, subordinate=05, sec-latency=0
Prefetchable memory behind bridge: 00000000dfe00000-00000000dfe00000
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
Capabilities: [40] Express Root Port (Slot+) IRQ 0
Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s unlimited, L1 unlimited
Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
Link: Supported Speed 2.5Gb/s, Width x1, ASPM L0s L1, Port 1
Link: Latency L0s <256ns, L1 <4us
Link: ASPM Disabled RCB 64 bytes CommClk+ ExtSynch-
Link: Speed 2.5Gb/s, Width x1
Slot: AtnBtn- PwrCtrl- MRL- AtnInd- PwrInd- HotPlug+ Surpise+
Slot: Number 1, PowerLimit 10.000000
Slot: Enabled AtnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq-
Slot: AttnInd Unknown, PwrInd Unknown, Power-
Root: Correctable- Non-Fatal- Fatal- PME-
Capabilities: [80] Message Signalled Interrupts: 64bit- Queue=0/0
Enable+
Address: fee00000 Data: 40d1
Capabilities: [90] #0d [0000]
Capabilities: [a0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00: 86 80 d0 27 06 05 10 00 01 00 04 06 04 00 81 00
10: 00 00 00 00 00 00 00 00 00 05 05 00 f0 00 00 20
20: f0 ff 00 00 e1 df e1 df 00 00 00 00 00 00 00 00
30: 00 00 00 00 40 00 00 00 00 00 00 00 0a 01 02 00
00:1c.2 PCI bridge: Intel Corporation 82801G (ICH7 Family) PCI Express Port 3
(rev 01) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 16 bytes
Bus: primary=00, secondary=04, subordinate=04, sec-latency=0
I/O behind bridge: 0000b000-0000bfff
Memory behind bridge: ff800000-ff8fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
Capabilities: [40] Express Root Port (Slot+) IRQ 0
Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s unlimited, L1 unlimited
Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
Link: Supported Speed 2.5Gb/s, Width x1, ASPM L0s L1, Port 3
Link: Latency L0s <256ns, L1 <4us
Link: ASPM Disabled RCB 64 bytes CommClk+ ExtSynch-
Link: Speed 2.5Gb/s, Width x1
Slot: AtnBtn- PwrCtrl- MRL- AtnInd- PwrInd- HotPlug+ Surpise+
Slot: Number 3, PowerLimit 10.000000
Slot: Enabled AtnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq-
Slot: AttnInd Unknown, PwrInd Unknown, Power-
Root: Correctable- Non-Fatal- Fatal- PME-
Capabilities: [80] Message Signalled Interrupts: 64bit- Queue=0/0
Enable+
Address: fee00000 Data: 40d9
Capabilities: [90] #0d [0000]
Capabilities: [a0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00: 86 80 d4 27 07 05 10 00 01 00 04 06 04 00 81 00
10: 00 00 00 00 00 00 00 00 00 04 04 00 b0 b0 00 00
20: 80 ff 80 ff f1 ff 01 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 40 00 00 00 00 00 00 00 05 03 02 00
00:1c.3 PCI bridge: Intel Corporation 82801G (ICH7 Family) PCI Express Port 4
(rev 01) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 16 bytes
Bus: primary=00, secondary=03, subordinate=03, sec-latency=0
I/O behind bridge: 0000a000-0000afff
Memory behind bridge: ff700000-ff7fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
Capabilities: [40] Express Root Port (Slot-) IRQ 0
Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s unlimited, L1 unlimited
Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
Link: Supported Speed 2.5Gb/s, Width x1, ASPM L0s L1, Port 4
Link: Latency L0s <256ns, L1 <4us
Link: ASPM Disabled RCB 64 bytes CommClk+ ExtSynch-
Link: Speed 2.5Gb/s, Width x1
Root: Correctable- Non-Fatal- Fatal- PME-
Capabilities: [80] Message Signalled Interrupts: 64bit- Queue=0/0
Enable+
Address: fee00000 Data: 40e1
Capabilities: [90] #0d [0000]
Capabilities: [a0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00: 86 80 d6 27 07 05 10 00 01 00 04 06 04 00 81 00
10: 00 00 00 00 00 00 00 00 00 03 03 00 a0 a0 00 00
20: 70 ff 70 ff f1 ff 01 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 40 00 00 00 00 00 00 00 0b 04 02 00
00:1c.4 PCI bridge: Intel Corporation 82801GR/GH/GHM (ICH7 Family) PCI Express
Port 5 (rev 01) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 16 bytes
Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
I/O behind bridge: 00009000-00009fff
Memory behind bridge: ff600000-ff6fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
Capabilities: [40] Express Root Port (Slot-) IRQ 0
Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s unlimited, L1 unlimited
Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
Link: Supported Speed 2.5Gb/s, Width x1, ASPM L0s L1, Port 5
Link: Latency L0s <256ns, L1 <4us
Link: ASPM Disabled RCB 64 bytes CommClk+ ExtSynch-
Link: Speed 2.5Gb/s, Width x1
Root: Correctable- Non-Fatal- Fatal- PME-
Capabilities: [80] Message Signalled Interrupts: 64bit- Queue=0/0
Enable+
Address: fee00000 Data: 40e9
Capabilities: [90] #0d [0000]
Capabilities: [a0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00: 86 80 e0 27 07 05 10 00 01 00 04 06 04 00 81 00
10: 00 00 00 00 00 00 00 00 00 02 02 00 90 90 00 00
20: 60 ff 60 ff f1 ff 01 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 40 00 00 00 00 00 00 00 0a 01 02 00
00:1d.0 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI #1 (rev
01) (prog-if 00 [UHCI])
Subsystem: ASUSTeK Computer Inc. Unknown device 8179
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 66
Region 4: I/O ports at e480 [size=32]
00: 86 80 c8 27 05 00 80 02 01 00 03 0c 00 00 80 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 81 e4 00 00 00 00 00 00 00 00 00 00 43 10 79 81
30: 00 00 00 00 00 00 00 00 00 00 00 00 03 01 00 00
00:1d.1 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI #2 (rev
01) (prog-if 00 [UHCI])
Subsystem: ASUSTeK Computer Inc. Unknown device 8179
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin B routed to IRQ 74
Region 4: I/O ports at e800 [size=32]
00: 86 80 c9 27 05 00 80 02 01 00 03 0c 00 00 00 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 01 e8 00 00 00 00 00 00 00 00 00 00 43 10 79 81
30: 00 00 00 00 00 00 00 00 00 00 00 00 07 02 00 00
00:1d.2 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI #3 (rev
01) (prog-if 00 [UHCI])
Subsystem: ASUSTeK Computer Inc. Unknown device 8179
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin C routed to IRQ 177
Region 4: I/O ports at e880 [size=32]
00: 86 80 ca 27 05 00 80 02 01 00 03 0c 00 00 00 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 81 e8 00 00 00 00 00 00 00 00 00 00 43 10 79 81
30: 00 00 00 00 00 00 00 00 00 00 00 00 05 03 00 00
00:1d.3 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI #4 (rev
01) (prog-if 00 [UHCI])
Subsystem: ASUSTeK Computer Inc. Unknown device 8179
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin D routed to IRQ 185
Region 4: I/O ports at ec00 [size=32]
00: 86 80 cb 27 05 00 80 02 01 00 03 0c 00 00 00 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 01 ec 00 00 00 00 00 00 00 00 00 00 43 10 79 81
30: 00 00 00 00 00 00 00 00 00 00 00 00 0b 04 00 00
00:1d.7 USB Controller: Intel Corporation 82801G (ICH7 Family) USB2 EHCI
Controller (rev 01) (prog-if 20 [EHCI])
Subsystem: ASUSTeK Computer Inc. Unknown device 8179
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 66
Region 0: Memory at ffafbc00 (32-bit, non-prefetchable) [size=1K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Debug port
00: 86 80 cc 27 06 00 90 02 01 20 03 0c 00 00 00 00
10: 00 bc af ff 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 43 10 79 81
30: 00 00 00 00 50 00 00 00 00 00 00 00 03 01 00 00
00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev e1) (prog-if 01
[Subtractive decode])
Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=32
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
Capabilities: [50] #0d [0000]
00: 86 80 4e 24 04 01 10 00 e1 01 04 06 00 00 01 00
10: 00 00 00 00 00 00 00 00 00 01 01 20 f0 00 80 22
20: f0 ff 00 00 f1 ff 01 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 50 00 00 00 00 00 00 00 00 00 02 00
00:1f.0 ISA bridge: Intel Corporation 82801GB/GR (ICH7 Family) LPC Interface
Bridge (rev 01)
Subsystem: ASUSTeK Computer Inc. Unknown device 8179
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Capabilities: [e0] Vendor Specific Information
00: 86 80 b8 27 07 00 10 02 01 00 01 06 00 00 80 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 43 10 79 81
30: 00 00 00 00 e0 00 00 00 00 00 00 00 00 00 00 00
00:1f.1 IDE interface: Intel Corporation 82801G (ICH7 Family) IDE Controller
(rev 01) (prog-if 8a [Master SecP PriP])
Subsystem: ASUSTeK Computer Inc. Unknown device 8179
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 50
Region 0: I/O ports at <unassigned>
Region 1: I/O ports at <unassigned>
Region 2: I/O ports at <unassigned>
Region 3: I/O ports at <unassigned>
Region 4: I/O ports at ffa0 [size=16]
00: 86 80 df 27 05 00 88 02 01 8a 01 01 00 00 00 00
10: 01 00 00 00 01 00 00 00 01 00 00 00 01 00 00 00
20: a1 ff 00 00 00 00 00 00 00 00 00 00 43 10 79 81
30: 00 00 00 00 00 00 00 00 00 00 00 00 00 01 00 00
00:1f.2 IDE interface: Intel Corporation 82801GB/GR/GH (ICH7 Family) Serial ATA
Storage Controller IDE (rev 01) (prog-if 8f [Master SecP SecO PriP PriO])
Subsystem: ASUSTeK Computer Inc. Unknown device 2601
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin B routed to IRQ 58
Region 0: I/O ports at e400 [size=8]
Region 1: I/O ports at e080 [size=4]
Region 2: I/O ports at e000 [size=8]
Region 3: I/O ports at dc00 [size=4]
Region 4: I/O ports at d880 [size=16]
Region 5: Memory at ffafb800 (32-bit, non-prefetchable) [size=1K]
Capabilities: [70] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00: 86 80 c0 27 07 00 b0 02 01 8f 01 01 00 00 00 00
10: 01 e4 00 00 81 e0 00 00 01 e0 00 00 01 dc 00 00
20: 81 d8 00 00 00 b8 af ff 00 00 00 00 43 10 01 26
30: 00 00 00 00 70 00 00 00 00 00 00 00 0a 02 00 00
00:1f.3 SMBus: Intel Corporation 82801G (ICH7 Family) SMBus Controller (rev 01)
Subsystem: ASUSTeK Computer Inc. Unknown device 8179
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin B routed to IRQ 0
Region 4: I/O ports at 0400 [size=32]
00: 86 80 da 27 01 00 80 02 01 00 05 0c 00 00 00 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 01 04 00 00 00 00 00 00 00 00 00 00 43 10 79 81
30: 00 00 00 00 00 00 00 00 00 00 00 00 00 02 00 00
02:00.0 Ethernet controller: Marvell Technology Group Ltd. 88E8053 PCI-E
Gigabit Ethernet Controller (rev 20)
Subsystem: ASUSTeK Computer Inc. Marvell 88E8053 Gigabit Ethernet
controller PCIe (Asus)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 16 bytes
Interrupt: pin A routed to IRQ 98
Region 0: Memory at ff6fc000 (64-bit, non-prefetchable) [size=16K]
Region 2: I/O ports at 9800 [size=256]
Expansion ROM at ff6c0000 [disabled] [size=128K]
Capabilities: [48] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=1 PME-
Capabilities: [50] Vital Product Data
Capabilities: [5c] Message Signalled Interrupts: 64bit+ Queue=0/1
Enable+
Address: 00000000fee00000 Data: 4062
Capabilities: [e0] Express Legacy Endpoint IRQ 0
Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s unlimited, L1 unlimited
Device: AtnBtn- AtnInd- PwrInd-
Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
Device: MaxPayload 128 bytes, MaxReadReq 512 bytes
Link: Supported Speed 2.5Gb/s, Width x1, ASPM L0s, Port 0
Link: Latency L0s <256ns, L1 unlimited
Link: ASPM Disabled RCB 128 bytes CommClk+ ExtSynch-
Link: Speed 2.5Gb/s, Width x1
00: ab 11 62 43 07 04 10 00 20 00 00 02 04 00 00 00
10: 04 c0 6f ff 00 00 00 00 01 98 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 43 10 42 81
30: 00 00 6c ff 48 00 00 00 00 00 00 00 0a 01 00 00
03:00.0 Ethernet controller: Marvell Technology Group Ltd. 88E8053 PCI-E
Gigabit Ethernet Controller (rev 20)
Subsystem: ASUSTeK Computer Inc. Marvell 88E8053 Gigabit Ethernet
controller PCIe (Asus)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 16 bytes
Interrupt: pin A routed to IRQ 90
Region 0: Memory at ff7fc000 (64-bit, non-prefetchable) [size=16K]
Region 2: I/O ports at a800 [size=256]
Expansion ROM at ff7c0000 [disabled] [size=128K]
Capabilities: [48] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=1 PME-
Capabilities: [50] Vital Product Data
Capabilities: [5c] Message Signalled Interrupts: 64bit+ Queue=0/1
Enable+
Address: 00000000fee00000 Data: 405a
Capabilities: [e0] Express Legacy Endpoint IRQ 0
Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s unlimited, L1 unlimited
Device: AtnBtn- AtnInd- PwrInd-
Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
Device: MaxPayload 128 bytes, MaxReadReq 512 bytes
Link: Supported Speed 2.5Gb/s, Width x1, ASPM L0s, Port 0
Link: Latency L0s <256ns, L1 unlimited
Link: ASPM Disabled RCB 128 bytes CommClk+ ExtSynch-
Link: Speed 2.5Gb/s, Width x1
00: ab 11 62 43 07 04 10 00 20 00 00 02 04 00 00 00
10: 04 c0 7f ff 00 00 00 00 01 a8 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 43 10 42 81
30: 00 00 7c ff 48 00 00 00 00 00 00 00 0b 01 00 00
04:00.0 Ethernet controller: Marvell Technology Group Ltd. 88E8052 PCI-E ASF
Gigabit Ethernet Controller (rev 22)
Subsystem: Marvell Technology Group Ltd. Marvell RDK-8052
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 16 bytes
Interrupt: pin A routed to IRQ 82
Region 0: Memory at ff8fc000 (64-bit, non-prefetchable) [size=16K]
Region 2: I/O ports at b800 [size=256]
Expansion ROM at ff8c0000 [disabled] [size=128K]
Capabilities: [48] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=1 PME-
Capabilities: [50] Vital Product Data
Capabilities: [5c] Message Signalled Interrupts: 64bit+ Queue=0/1
Enable+
Address: 00000000fee00000 Data: 4052
Capabilities: [e0] Express Legacy Endpoint IRQ 0
Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s unlimited, L1 unlimited
Device: AtnBtn- AtnInd- PwrInd-
Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
Device: MaxPayload 128 bytes, MaxReadReq 512 bytes
Link: Supported Speed 2.5Gb/s, Width x1, ASPM L0s, Port 0
Link: Latency L0s <256ns, L1 unlimited
Link: ASPM Disabled RCB 128 bytes CommClk+ ExtSynch-
Link: Speed 2.5Gb/s, Width x1
00: ab 11 60 43 07 04 10 00 22 00 00 02 04 00 00 00
10: 04 c0 8f ff 00 00 00 00 01 b8 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 ab 11 21 52
30: 00 00 8c ff 48 00 00 00 00 00 00 00 05 01 00 00
06:00.0 VGA compatible controller: ATI Technologies Inc RV370 5B60 [Radeon X300
(PCIE)] (prog-if 00 [VGA])
Subsystem: VISIONTEK Unknown device 0401
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 16 bytes
Interrupt: pin A routed to IRQ 10
Region 0: Memory at e0000000 (32-bit, prefetchable) [size=128M]
Region 1: I/O ports at c800 [size=256]
Region 2: Memory at ff9f0000 (32-bit, non-prefetchable) [size=64K]
Expansion ROM at ff9c0000 [disabled] [size=128K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Express Endpoint IRQ 0
Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag+
Device: Latency L0s <128ns, L1 <2us
Device: AtnBtn- AtnInd- PwrInd-
Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
Device: RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
Link: Supported Speed 2.5Gb/s, Width x16, ASPM L0s L1, Port 0
Link: Latency L0s <128ns, L1 <1us
Link: ASPM Disabled RCB 64 bytes CommClk+ ExtSynch-
Link: Speed 2.5Gb/s, Width x16
Capabilities: [80] Message Signalled Interrupts: 64bit+ Queue=0/0
Enable-
Address: 0000000000000000 Data: 0000
00: 02 10 60 5b 07 00 10 00 00 00 00 03 04 00 80 00
10: 08 00 00 e0 01 c8 00 00 00 00 9f ff 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 45 15 01 04
30: 00 00 9c ff 50 00 00 00 00 00 00 00 0a 01 00 00
06:00.1 Display controller: ATI Technologies Inc RV370 [Radeon X300SE]
Subsystem: VISIONTEK Unknown device 0400
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 16 bytes
Region 0: Memory at ff9e0000 (32-bit, non-prefetchable) [size=64K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Express Endpoint IRQ 0
Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s <128ns, L1 <2us
Device: AtnBtn- AtnInd- PwrInd-
Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
Link: Supported Speed 2.5Gb/s, Width x16, ASPM L0s L1, Port 0
Link: Latency L0s <128ns, L1 <1us
Link: ASPM Disabled RCB 64 bytes CommClk+ ExtSynch-
Link: Speed 2.5Gb/s, Width x16
00: 02 10 70 5b 07 00 10 00 00 00 80 03 04 00 00 00
10: 00 00 9e ff 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 45 15 00 04
30: 00 00 00 00 50 00 00 00 00 00 00 00 ff 00 00 00
00:00.0 Host bridge: Intel Corporation 975X Express Memory Controller Hub (rev
c0)
Subsystem: ASUSTeK Computer Inc. Unknown device 8178
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort+ >SERR- <PERR-
Latency: 0
Capabilities: [e0] Vendor Specific Information
00: 86 80 7c 27 06 00 90 20 c0 00 00 06 00 00 00 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 43 10 78 81
30: 00 00 00 00 e0 00 00 00 00 00 00 00 00 00 00 00
00:01.0 PCI bridge: Intel Corporation 975X Express PCI Express Root Port (rev
c0) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 16 bytes
Bus: primary=00, secondary=06, subordinate=06, sec-latency=0
I/O behind bridge: 0000c000-0000cfff
Memory behind bridge: ff900000-ff9fffff
Prefetchable memory behind bridge: 00000000dff00000-00000000efe00000
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA+ MAbort- >Reset- FastB2B-
Capabilities: [88] #0d [0000]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [90] Message Signalled Interrupts: 64bit- Queue=0/0
Enable+
Address: fee00000 Data: 4051
Capabilities: [a0] Express Root Port (Slot+) IRQ 0
Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s <64ns, L1 <1us
Device: Errors: Correctable+ Non-Fatal+ Fatal+ Unsupported+
Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
Link: Supported Speed 2.5Gb/s, Width x16, ASPM L0s, Port 2
Link: Latency L0s <256ns, L1 <4us
Link: ASPM Disabled RCB 64 bytes CommClk+ ExtSynch-
Link: Speed 2.5Gb/s, Width x16
Slot: AtnBtn- PwrCtrl- MRL- AtnInd- PwrInd- HotPlug- Surpise-
Slot: Number 0, PowerLimit 75.000000
Slot: Enabled AtnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq-
Slot: AttnInd Off, PwrInd On, Power-
Root: Correctable- Non-Fatal- Fatal- PME-
00: 86 80 7d 27 07 05 10 00 c0 00 04 06 04 00 01 00
10: 00 00 00 00 00 00 00 00 00 06 06 00 c0 c0 00 20
20: 90 ff 90 ff f1 df e1 ef 00 00 00 00 00 00 00 00
30: 00 00 00 00 88 00 00 00 00 00 00 00 0a 01 0a 00
00:1b.0 Audio device: Intel Corporation 82801G (ICH7 Family) High Definition
Audio Controller (rev 01)
Subsystem: ASUSTeK Computer Inc. Unknown device 81d8
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 16 bytes
Interrupt: pin A routed to IRQ 19
Region 0: Memory at ffafc000 (64-bit, non-prefetchable) [size=16K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=55mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [60] Message Signalled Interrupts: 64bit+ Queue=0/0
Enable-
Address: 0000000000000000 Data: 0000
Capabilities: [70] Express Unknown type IRQ 0
Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s <64ns, L1 <1us
Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+
Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
Link: Supported Speed unknown, Width x0, ASPM unknown, Port 0
Link: Latency L0s <64ns, L1 <1us
Link: ASPM Disabled CommClk- ExtSynch-
Link: Speed unknown, Width x0
00: 86 80 d8 27 06 00 10 00 01 00 03 04 04 00 00 00
10: 04 c0 af ff 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 43 10 d8 81
30: 00 00 00 00 50 00 00 00 00 00 00 00 0b 01 00 00
00:1c.0 PCI bridge: Intel Corporation 82801G (ICH7 Family) PCI Express Port 1
(rev 01) (prog-if 00 [Normal decode])
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 16 bytes
Bus: primary=00, secondary=05, subordinate=05, sec-latency=0
I/O behind bridge: 0000f000-00000fff
Memory behind bridge: fff00000-000fffff
Prefetchable memory behind bridge: 00000000dfe00000-00000000dfe00000
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
Capabilities: [40] Express Root Port (Slot+) IRQ 0
Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s unlimited, L1 unlimited
Device: Errors: Correctable+ Non-Fatal+ Fatal+ Unsupported+
Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
Link: Supported Speed 2.5Gb/s, Width x1, ASPM L0s L1, Port 1
Link: Latency L0s <256ns, L1 <4us
Link: ASPM Disabled RCB 64 bytes CommClk+ ExtSynch-
Link: Speed 2.5Gb/s, Width x1
Slot: AtnBtn- PwrCtrl- MRL- AtnInd- PwrInd- HotPlug+ Surpise+
Slot: Number 1, PowerLimit 10.000000
Slot: Enabled AtnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq-
Slot: AttnInd Unknown, PwrInd Unknown, Power-
Root: Correctable- Non-Fatal- Fatal- PME-
Capabilities: [80] Message Signalled Interrupts: 64bit- Queue=0/0
Enable+
Address: fee00000 Data: 4059
Capabilities: [90] #0d [0000]
Capabilities: [a0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00: 86 80 d0 27 06 05 10 00 01 00 04 06 04 00 81 00
10: 00 00 00 00 00 00 00 00 00 05 05 00 f0 00 00 20
20: f0 ff 00 00 e1 df e1 df 00 00 00 00 00 00 00 00
30: 00 00 00 00 40 00 00 00 00 00 00 00 0a 01 02 00
00:1c.2 PCI bridge: Intel Corporation 82801G (ICH7 Family) PCI Express Port 3
(rev 01) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 16 bytes
Bus: primary=00, secondary=04, subordinate=04, sec-latency=0
I/O behind bridge: 0000b000-0000bfff
Memory behind bridge: ff800000-ff8fffff
Prefetchable memory behind bridge: 00000000fff00000-0000000000000000
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
Capabilities: [40] Express Root Port (Slot+) IRQ 0
Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s unlimited, L1 unlimited
Device: Errors: Correctable+ Non-Fatal+ Fatal+ Unsupported+
Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
Link: Supported Speed 2.5Gb/s, Width x1, ASPM L0s L1, Port 3
Link: Latency L0s <256ns, L1 <4us
Link: ASPM Disabled RCB 64 bytes CommClk+ ExtSynch-
Link: Speed 2.5Gb/s, Width x1
Slot: AtnBtn- PwrCtrl- MRL- AtnInd- PwrInd- HotPlug+ Surpise+
Slot: Number 3, PowerLimit 10.000000
Slot: Enabled AtnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq-
Slot: AttnInd Unknown, PwrInd Unknown, Power-
Root: Correctable- Non-Fatal- Fatal- PME-
Capabilities: [80] Message Signalled Interrupts: 64bit- Queue=0/0
Enable+
Address: fee00000 Data: 4061
Capabilities: [90] #0d [0000]
Capabilities: [a0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00: 86 80 d4 27 07 05 10 00 01 00 04 06 04 00 81 00
10: 00 00 00 00 00 00 00 00 00 04 04 00 b0 b0 00 00
20: 80 ff 80 ff f1 ff 01 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 40 00 00 00 00 00 00 00 05 03 02 00
00:1c.3 PCI bridge: Intel Corporation 82801G (ICH7 Family) PCI Express Port 4
(rev 01) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 16 bytes
Bus: primary=00, secondary=03, subordinate=03, sec-latency=0
I/O behind bridge: 0000a000-0000afff
Memory behind bridge: ff700000-ff7fffff
Prefetchable memory behind bridge: 00000000fff00000-0000000000000000
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
Capabilities: [40] Express Root Port (Slot-) IRQ 0
Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s unlimited, L1 unlimited
Device: Errors: Correctable+ Non-Fatal+ Fatal+ Unsupported+
Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
Link: Supported Speed 2.5Gb/s, Width x1, ASPM L0s L1, Port 4
Link: Latency L0s <256ns, L1 <4us
Link: ASPM Disabled RCB 64 bytes CommClk+ ExtSynch-
Link: Speed 2.5Gb/s, Width x1
Root: Correctable- Non-Fatal- Fatal- PME-
Capabilities: [80] Message Signalled Interrupts: 64bit- Queue=0/0
Enable+
Address: fee00000 Data: 4069
Capabilities: [90] #0d [0000]
Capabilities: [a0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00: 86 80 d6 27 07 05 10 00 01 00 04 06 04 00 81 00
10: 00 00 00 00 00 00 00 00 00 03 03 00 a0 a0 00 00
20: 70 ff 70 ff f1 ff 01 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 40 00 00 00 00 00 00 00 0b 04 02 00
00:1c.4 PCI bridge: Intel Corporation 82801GR/GH/GHM (ICH7 Family) PCI Express
Port 5 (rev 01) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 16 bytes
Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
I/O behind bridge: 00009000-00009fff
Memory behind bridge: ff600000-ff6fffff
Prefetchable memory behind bridge: 00000000fff00000-0000000000000000
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
Capabilities: [40] Express Root Port (Slot-) IRQ 0
Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s unlimited, L1 unlimited
Device: Errors: Correctable+ Non-Fatal+ Fatal+ Unsupported+
Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
Link: Supported Speed 2.5Gb/s, Width x1, ASPM L0s L1, Port 5
Link: Latency L0s <256ns, L1 <4us
Link: ASPM Disabled RCB 64 bytes CommClk+ ExtSynch-
Link: Speed 2.5Gb/s, Width x1
Root: Correctable- Non-Fatal- Fatal- PME-
Capabilities: [80] Message Signalled Interrupts: 64bit- Queue=0/0
Enable+
Address: fee00000 Data: 4071
Capabilities: [90] #0d [0000]
Capabilities: [a0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00: 86 80 e0 27 07 05 10 00 01 00 04 06 04 00 81 00
10: 00 00 00 00 00 00 00 00 00 02 02 00 90 90 00 00
20: 60 ff 60 ff f1 ff 01 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 40 00 00 00 00 00 00 00 0a 01 02 00
00:1d.0 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI #1 (rev
01) (prog-if 00 [UHCI])
Subsystem: ASUSTeK Computer Inc. Unknown device 8179
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 20
Region 4: I/O ports at e480 [size=32]
00: 86 80 c8 27 05 00 80 02 01 00 03 0c 00 00 80 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 81 e4 00 00 00 00 00 00 00 00 00 00 43 10 79 81
30: 00 00 00 00 00 00 00 00 00 00 00 00 03 01 00 00
00:1d.1 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI #2 (rev
01) (prog-if 00 [UHCI])
Subsystem: ASUSTeK Computer Inc. Unknown device 8179
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin B routed to IRQ 17
Region 4: I/O ports at e800 [size=32]
00: 86 80 c9 27 05 00 80 02 01 00 03 0c 00 00 00 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 01 e8 00 00 00 00 00 00 00 00 00 00 43 10 79 81
30: 00 00 00 00 00 00 00 00 00 00 00 00 07 02 00 00
00:1d.2 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI #3 (rev
01) (prog-if 00 [UHCI])
Subsystem: ASUSTeK Computer Inc. Unknown device 8179
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin C routed to IRQ 18
Region 4: I/O ports at e880 [size=32]
00: 86 80 ca 27 05 00 80 02 01 00 03 0c 00 00 00 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 81 e8 00 00 00 00 00 00 00 00 00 00 43 10 79 81
30: 00 00 00 00 00 00 00 00 00 00 00 00 05 03 00 00
00:1d.3 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI #4 (rev
01) (prog-if 00 [UHCI])
Subsystem: ASUSTeK Computer Inc. Unknown device 8179
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin D routed to IRQ 19
Region 4: I/O ports at ec00 [size=32]
00: 86 80 cb 27 05 00 80 02 01 00 03 0c 00 00 00 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 01 ec 00 00 00 00 00 00 00 00 00 00 43 10 79 81
30: 00 00 00 00 00 00 00 00 00 00 00 00 0b 04 00 00
00:1d.7 USB Controller: Intel Corporation 82801G (ICH7 Family) USB2 EHCI
Controller (rev 01) (prog-if 20 [EHCI])
Subsystem: ASUSTeK Computer Inc. Unknown device 8179
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 20
Region 0: Memory at ffafbc00 (32-bit, non-prefetchable) [size=1K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Debug port
00: 86 80 cc 27 06 00 90 02 01 20 03 0c 00 00 00 00
10: 00 bc af ff 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 43 10 79 81
30: 00 00 00 00 50 00 00 00 00 00 00 00 03 01 00 00
00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev e1) (prog-if 01
[Subtractive decode])
Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=32
I/O behind bridge: 0000f000-00000fff
Memory behind bridge: fff00000-000fffff
Prefetchable memory behind bridge: 00000000fff00000-0000000000000000
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
Capabilities: [50] #0d [0000]
00: 86 80 4e 24 04 01 10 00 e1 01 04 06 00 00 01 00
10: 00 00 00 00 00 00 00 00 00 01 01 20 f0 00 80 22
20: f0 ff 00 00 f1 ff 01 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 50 00 00 00 00 00 00 00 00 00 02 00
00:1f.0 ISA bridge: Intel Corporation 82801GB/GR (ICH7 Family) LPC Interface
Bridge (rev 01)
Subsystem: ASUSTeK Computer Inc. Unknown device 8179
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Capabilities: [e0] Vendor Specific Information
00: 86 80 b8 27 07 00 10 02 01 00 01 06 00 00 80 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 43 10 79 81
30: 00 00 00 00 e0 00 00 00 00 00 00 00 00 00 00 00
00:1f.1 IDE interface: Intel Corporation 82801G (ICH7 Family) IDE Controller
(rev 01) (prog-if 8a [Master SecP PriP])
Subsystem: ASUSTeK Computer Inc. Unknown device 8179
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 22
Region 0: I/O ports at 01f0 [size=8]
Region 1: I/O ports at 03f4 [size=1]
Region 2: I/O ports at 0170 [size=8]
Region 3: I/O ports at 0374 [size=1]
Region 4: I/O ports at ffa0 [size=16]
00: 86 80 df 27 05 00 88 02 01 8a 01 01 00 00 00 00
10: 01 00 00 00 01 00 00 00 01 00 00 00 01 00 00 00
20: a1 ff 00 00 00 00 00 00 00 00 00 00 43 10 79 81
30: 00 00 00 00 00 00 00 00 00 00 00 00 00 01 00 00
00:1f.2 IDE interface: Intel Corporation 82801GB/GR/GH (ICH7 Family) Serial ATA
Storage Controller IDE (rev 01) (prog-if 8f [Master SecP SecO PriP PriO])
Subsystem: ASUSTeK Computer Inc. Unknown device 2601
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin B routed to IRQ 23
Region 0: I/O ports at e400 [size=8]
Region 1: I/O ports at e080 [size=4]
Region 2: I/O ports at e000 [size=8]
Region 3: I/O ports at dc00 [size=4]
Region 4: I/O ports at d880 [size=16]
Region 5: Memory at ffafb800 (32-bit, non-prefetchable) [size=1K]
Capabilities: [70] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00: 86 80 c0 27 07 00 b0 02 01 8f 01 01 00 00 00 00
10: 01 e4 00 00 81 e0 00 00 01 e0 00 00 01 dc 00 00
20: 81 d8 00 00 00 b8 af ff 00 00 00 00 43 10 01 26
30: 00 00 00 00 70 00 00 00 00 00 00 00 0a 02 00 00
00:1f.3 SMBus: Intel Corporation 82801G (ICH7 Family) SMBus Controller (rev 01)
Subsystem: ASUSTeK Computer Inc. Unknown device 8179
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin B routed to IRQ 23
Region 4: I/O ports at 0400 [size=32]
00: 86 80 da 27 01 00 80 02 01 00 05 0c 00 00 00 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 01 04 00 00 00 00 00 00 00 00 00 00 43 10 79 81
30: 00 00 00 00 00 00 00 00 00 00 00 00 00 02 00 00
02:00.0 Ethernet controller: Marvell Technology Group Ltd. 88E8053 PCI-E
Gigabit Ethernet Controller (rev 20)
Subsystem: ASUSTeK Computer Inc. Marvell 88E8053 Gigabit Ethernet
controller PCIe (Asus)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 16 bytes
Interrupt: pin A routed to IRQ 312
Region 0: Memory at ff6fc000 (64-bit, non-prefetchable) [size=16K]
Region 2: I/O ports at 9800 [size=256]
Expansion ROM at ff6c0000 [disabled] [size=128K]
Capabilities: [48] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=1 PME-
Capabilities: [50] Vital Product Data
Capabilities: [5c] Message Signalled Interrupts: 64bit+ Queue=0/1
Enable+
Address: 00000000fee00000 Data: 40a9
Capabilities: [e0] Express Legacy Endpoint IRQ 0
Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s unlimited, L1 unlimited
Device: AtnBtn- AtnInd- PwrInd-
Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
Device: MaxPayload 128 bytes, MaxReadReq 512 bytes
Link: Supported Speed 2.5Gb/s, Width x1, ASPM L0s, Port 0
Link: Latency L0s <256ns, L1 unlimited
Link: ASPM Disabled RCB 128 bytes CommClk+ ExtSynch-
Link: Speed 2.5Gb/s, Width x1
00: ab 11 62 43 07 04 10 00 20 00 00 02 04 00 00 00
10: 04 c0 6f ff 00 00 00 00 01 98 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 43 10 42 81
30: 00 00 6c ff 48 00 00 00 00 00 00 00 0a 01 00 00
03:00.0 Ethernet controller: Marvell Technology Group Ltd. 88E8053 PCI-E
Gigabit Ethernet Controller (rev 20)
Subsystem: ASUSTeK Computer Inc. Marvell 88E8053 Gigabit Ethernet
controller PCIe (Asus)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 16 bytes
Interrupt: pin A routed to IRQ 313
Region 0: Memory at ff7fc000 (64-bit, non-prefetchable) [size=16K]
Region 2: I/O ports at a800 [size=256]
Expansion ROM at ff7c0000 [disabled] [size=128K]
Capabilities: [48] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=1 PME-
Capabilities: [50] Vital Product Data
Capabilities: [5c] Message Signalled Interrupts: 64bit+ Queue=0/1
Enable+
Address: 00000000fee00000 Data: 40a1
Capabilities: [e0] Express Legacy Endpoint IRQ 0
Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s unlimited, L1 unlimited
Device: AtnBtn- AtnInd- PwrInd-
Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
Device: MaxPayload 128 bytes, MaxReadReq 512 bytes
Link: Supported Speed 2.5Gb/s, Width x1, ASPM L0s, Port 0
Link: Latency L0s <256ns, L1 unlimited
Link: ASPM Disabled RCB 128 bytes CommClk+ ExtSynch-
Link: Speed 2.5Gb/s, Width x1
00: ab 11 62 43 07 04 10 00 20 00 00 02 04 00 00 00
10: 04 c0 7f ff 00 00 00 00 01 a8 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 43 10 42 81
30: 00 00 7c ff 48 00 00 00 00 00 00 00 0b 01 00 00
04:00.0 Ethernet controller: Marvell Technology Group Ltd. 88E8052 PCI-E ASF
Gigabit Ethernet Controller (rev 22)
Subsystem: Marvell Technology Group Ltd. Marvell RDK-8052
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 16 bytes
Interrupt: pin A routed to IRQ 314
Region 0: Memory at ff8fc000 (64-bit, non-prefetchable) [size=16K]
Region 2: I/O ports at b800 [size=256]
Expansion ROM at ff8c0000 [disabled] [size=128K]
Capabilities: [48] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=1 PME-
Capabilities: [50] Vital Product Data
Capabilities: [5c] Message Signalled Interrupts: 64bit+ Queue=0/1
Enable+
Address: 00000000fee00000 Data: 4099
Capabilities: [e0] Express Legacy Endpoint IRQ 0
Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s unlimited, L1 unlimited
Device: AtnBtn- AtnInd- PwrInd-
Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
Device: MaxPayload 128 bytes, MaxReadReq 512 bytes
Link: Supported Speed 2.5Gb/s, Width x1, ASPM L0s, Port 0
Link: Latency L0s <256ns, L1 unlimited
Link: ASPM Disabled RCB 128 bytes CommClk+ ExtSynch-
Link: Speed 2.5Gb/s, Width x1
00: ab 11 60 43 07 04 10 00 22 00 00 02 04 00 00 00
10: 04 c0 8f ff 00 00 00 00 01 b8 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 ab 11 21 52
30: 00 00 8c ff 48 00 00 00 00 00 00 00 05 01 00 00
06:00.0 VGA compatible controller: ATI Technologies Inc RV370 5B60 [Radeon X300
(PCIE)] (prog-if 00 [VGA])
Subsystem: VISIONTEK Unknown device 0401
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 16 bytes
Interrupt: pin A routed to IRQ 16
Region 0: Memory at e0000000 (32-bit, prefetchable) [size=128M]
Region 1: I/O ports at c800 [size=256]
Region 2: Memory at ff9f0000 (32-bit, non-prefetchable) [size=64K]
Expansion ROM at ff9c0000 [disabled] [size=128K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Express Endpoint IRQ 0
Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag+
Device: Latency L0s <128ns, L1 <2us
Device: AtnBtn- AtnInd- PwrInd-
Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
Device: RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
Link: Supported Speed 2.5Gb/s, Width x16, ASPM L0s L1, Port 0
Link: Latency L0s <128ns, L1 <1us
Link: ASPM Disabled RCB 64 bytes CommClk+ ExtSynch-
Link: Speed 2.5Gb/s, Width x16
Capabilities: [80] Message Signalled Interrupts: 64bit+ Queue=0/0
Enable-
Address: 0000000000000000 Data: 0000
00: 02 10 60 5b 07 00 10 00 00 00 00 03 04 00 80 00
10: 08 00 00 e0 01 c8 00 00 00 00 9f ff 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 45 15 01 04
30: 00 00 9c ff 50 00 00 00 00 00 00 00 0a 01 00 00
06:00.1 Display controller: ATI Technologies Inc RV370 [Radeon X300SE]
Subsystem: VISIONTEK Unknown device 0400
Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 16 bytes
Region 0: Memory at ff9e0000 (32-bit, non-prefetchable) [disabled]
[size=64K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Express Endpoint IRQ 0
Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s <128ns, L1 <2us
Device: AtnBtn- AtnInd- PwrInd-
Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
Link: Supported Speed 2.5Gb/s, Width x16, ASPM L0s L1, Port 0
Link: Latency L0s <128ns, L1 <1us
Link: ASPM Disabled RCB 64 bytes CommClk+ ExtSynch-
Link: Speed 2.5Gb/s, Width x16
00: 02 10 70 5b 04 00 10 00 00 00 80 03 04 00 00 00
10: 00 00 9e ff 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 45 15 00 04
30: 00 00 00 00 50 00 00 00 00 00 00 00 ff 00 00 00
-------------------------------------------------------------------------
Take Surveys. Earn Cash. Influence the Future of IT
Join SourceForge.net's Techsay panel and you'll get the chance to share your
opinions on IT & business topics through brief surveys - and earn cash
http://www.techsay.com/default.php?page=join.php&p=sourceforge&CID=DEVDEV
--
_______________________________________________
Dri-devel mailing list
[email protected]
https://lists.sourceforge.net/lists/listinfo/dri-devel
