On Sat, Apr 06, 2019 at 01:45:03AM +0200, [email protected] wrote: > From: Ondrej Jirman <[email protected]> > > Orange Pi 3 is a H6 based SBC made by Xulong, released in > January 2019. It has the following features: > > - Allwinner H6 quad-core 64-bit ARM Cortex-A53 > - GPU Mali-T720 > - 1GB or 2GB LPDDR3 RAM > - AXP805 PMIC > - AP6256 Wifi/BT 5.0 > - USB 2.0 host port (A) > - USB 2.0 micro usb, OTG > - USB 3.0 Host + 4 port USB hub (GL3510) > - Gigabit Ethernet (Realtek RTL8211E phy) > - HDMI 2.0 port > - soldered eMMC (optional) > - 3x LED (one is on the bottom) > - microphone > - audio jack > - PCIe > > Add basic support for the board. > > Signed-off-by: Ondrej Jirman <[email protected]> > --- > arch/arm64/boot/dts/allwinner/Makefile | 1 + > .../dts/allwinner/sun50i-h6-orangepi-3.dts | 212 ++++++++++++++++++ > 2 files changed, 213 insertions(+) > create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-h6-orangepi-3.dts > > diff --git a/arch/arm64/boot/dts/allwinner/Makefile > b/arch/arm64/boot/dts/allwinner/Makefile > index e4dce2f6fa3a..285a7cb5135b 100644 > --- a/arch/arm64/boot/dts/allwinner/Makefile > +++ b/arch/arm64/boot/dts/allwinner/Makefile > @@ -20,6 +20,7 @@ dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-orangepi-pc2.dtb > dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-orangepi-prime.dtb > dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-orangepi-zero-plus.dtb > dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-orangepi-zero-plus2.dtb > +dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-orangepi-3.dtb > dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-orangepi-lite2.dtb > dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-orangepi-one-plus.dtb > dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-pine-h64.dtb > diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h6-orangepi-3.dts > b/arch/arm64/boot/dts/allwinner/sun50i-h6-orangepi-3.dts > new file mode 100644 > index 000000000000..7a2424fcaed7 > --- /dev/null > +++ b/arch/arm64/boot/dts/allwinner/sun50i-h6-orangepi-3.dts > @@ -0,0 +1,212 @@ > +// SPDX-License-Identifier: (GPL-2.0+ or MIT) > +/* > + * Copyright (C) 2019 Ondřej Jirman <[email protected]> > + */ > + > +/dts-v1/; > + > +#include "sun50i-h6.dtsi" > + > +#include <dt-bindings/gpio/gpio.h> > + > +/ { > + model = "OrangePi 3"; > + compatible = "xunlong,orangepi-3", "allwinner,sun50i-h6";
As Clement pointed out, this should be documented in
Documentation/devicetree/bindings/arm/sunxi.yaml
It's part of sunxi/for-next only at this point, and it will go through
a different branch than the H6 DTS, so it would be great to have it in
a separate patch.
> + aliases {
> + serial0 = &uart0;
> + };
> +
> + chosen {
> + stdout-path = "serial0:115200n8";
> + };
> +
> + leds {
> + compatible = "gpio-leds";
> +
> + power {
> + label = "orangepi:red:power";
> + gpios = <&r_pio 0 4 GPIO_ACTIVE_HIGH>; /* PL4 */
> + default-state = "on";
> + };
> +
> + status {
> + label = "orangepi:green:status";
> + gpios = <&r_pio 0 7 GPIO_ACTIVE_HIGH>; /* PL7 */
> + };
> + };
> +
> + reg_vcc5v: vcc5v {
> + /* board wide 5V supply directly from the DC jack */
> + compatible = "regulator-fixed";
> + regulator-name = "vcc-5v";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + regulator-always-on;
> + };
> +};
> +
> +&cpu0 {
> + cpu-supply = <®_dcdca>;
> +};
> +
> +&ehci0 {
> + status = "okay";
> +};
> +
> +&ehci3 {
> + status = "okay";
> +};
> +
> +&mmc0 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&mmc0_pins>;
> + vmmc-supply = <®_cldo1>;
> + cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */
> + bus-width = <4>;
> + status = "okay";
> +};
> +
> +&ohci0 {
> + status = "okay";
> +};
> +
> +&ohci3 {
> + status = "okay";
> +};
> +
> +&pio {
> + vcc-pc-supply = <®_bldo2>;
> + vcc-pd-supply = <®_cldo1>;
> +};
> +
> +&r_i2c {
> + status = "okay";
> +
> + axp805: pmic@36 {
> + compatible = "x-powers,axp805", "x-powers,axp806";
> + reg = <0x36>;
> + interrupt-parent = <&r_intc>;
> + interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
> + interrupt-controller;
> + #interrupt-cells = <1>;
> + x-powers,self-working-mode;
> + vina-supply = <®_vcc5v>;
> + vinb-supply = <®_vcc5v>;
> + vinc-supply = <®_vcc5v>;
> + vind-supply = <®_vcc5v>;
> + vine-supply = <®_vcc5v>;
> + aldoin-supply = <®_vcc5v>;
> + bldoin-supply = <®_vcc5v>;
> + cldoin-supply = <®_vcc5v>;
> +
> + regulators {
> + reg_aldo1: aldo1 {
> + regulator-always-on;
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-name = "vcc-pl-led-ir";
> + };
> +
> + reg_aldo2: aldo2 {
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-name = "vcc33-audio-tv-ephy-mac";
> + };
> +
> + /* ALDO3 is shorted to CLDO1 */
> + reg_aldo3: aldo3 {
> + regulator-always-on;
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-name =
> "vcc33-io-pd-emmc-sd-usb-uart-1";
> + };
> +
> + reg_bldo1: bldo1 {
> + regulator-always-on;
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-name = "vcc18-dram-bias-pll";
> + };
> +
> + reg_bldo2: bldo2 {
> + regulator-always-on;
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-name = "vcc-efuse-pcie-hdmi-pc";
> + };
> +
> + bldo3 {
> + /* unused */
> + };
> +
> + bldo4 {
> + /* unused */
> + };
> +
> + reg_cldo1: cldo1 {
> + regulator-always-on;
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-name =
> "vcc33-io-pd-emmc-sd-usb-uart-2";
> + };
> +
> + cldo2 {
> + /* unused */
> + };
> +
> + cldo3 {
> + /* unused */
> + };
> +
> + reg_dcdca: dcdca {
> + regulator-always-on;
> + regulator-min-microvolt = <800000>;
> + regulator-max-microvolt = <1160000>;
> + regulator-name = "vdd-cpu";
> + };
> +
> + reg_dcdcc: dcdcc {
> + regulator-min-microvolt = <810000>;
> + regulator-max-microvolt = <1080000>;
> + regulator-name = "vdd-gpu";
> + };
> +
> + reg_dcdcd: dcdcd {
> + regulator-always-on;
> + regulator-min-microvolt = <960000>;
> + regulator-max-microvolt = <960000>;
> + regulator-name = "vdd-sys";
> + };
> +
> + reg_dcdce: dcdce {
> + regulator-always-on;
> + regulator-min-microvolt = <1200000>;
> + regulator-max-microvolt = <1200000>;
> + regulator-name = "vcc-dram";
> + };
> +
> + sw {
> + /* unused */
> + };
> + };
> + };
> +};
> +
> +&uart0 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&uart0_ph_pins>;
> + status = "okay";
> +};
> +
> +&usb2otg {
> + dr_mode = "host";
> + status = "okay";
> +};
> +
> +&usb2phy {
> + usb0_id_det-gpios = <&pio 2 15 GPIO_ACTIVE_HIGH>; /* PC15 */
> + usb0_vbus-supply = <®_vcc5v>;
> + usb3_vbus-supply = <®_vcc5v>;
> + status = "okay";
If we have an ID pin, then why is the OTG controller set to host?
Maxime
--
Maxime Ripard, Bootlin
Embedded Linux and Kernel engineering
https://bootlin.com
signature.asc
Description: PGP signature
_______________________________________________ dri-devel mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/dri-devel
