From: Ondrej Jirman <[email protected]> Orange Pi 3 has two regulators that power the Realtek RTL8211E. According to the phy datasheet, both regulators need to be enabled at the same time, but we can only specify a single phy-supply in the DT.
This can be achieved by making one regulator depedning on the other via vin-supply. While it's not a technically correct description of the hardware, it achieves the purpose. All values of RX/TX delay were tested exhaustively and a middle one of the working values was chosen. Signed-off-by: Ondrej Jirman <[email protected]> --- .../dts/allwinner/sun50i-h6-orangepi-3.dts | 44 +++++++++++++++++++ 1 file changed, 44 insertions(+) diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h6-orangepi-3.dts b/arch/arm64/boot/dts/allwinner/sun50i-h6-orangepi-3.dts index 644946749088..5270142527f5 100644 --- a/arch/arm64/boot/dts/allwinner/sun50i-h6-orangepi-3.dts +++ b/arch/arm64/boot/dts/allwinner/sun50i-h6-orangepi-3.dts @@ -15,6 +15,7 @@ aliases { serial0 = &uart0; + ethernet0 = &emac; }; chosen { @@ -64,6 +65,27 @@ regulator-max-microvolt = <5000000>; regulator-always-on; }; + + /* + * The board uses 2.5V RGMII signalling. Power sequence + * to enable the phy is to enable GMAC-2V5 and GMAC-3V3 (aldo2) + * power rails at the same time and to wait 100ms. + */ + reg_gmac_2v5: gmac-2v5 { + compatible = "regulator-fixed"; + regulator-name = "gmac-2v5"; + regulator-min-microvolt = <2500000>; + regulator-max-microvolt = <2500000>; + startup-delay-us = <100000>; + enable-active-high; + gpio = <&pio 3 6 GPIO_ACTIVE_HIGH>; /* PD6 */ + + /* The real parent of gmac-2v5 is reg_vcc5v, but we need + * to enable two regulators to power the phy. This is one + * way to achieve that. + */ + vin-supply = <®_aldo2>; /* GMAC-3V3 */ + }; }; &cpu0 { @@ -82,6 +104,17 @@ status = "okay"; }; +&emac { + pinctrl-names = "default"; + pinctrl-0 = <&ext_rgmii_pins>; + phy-mode = "rgmii"; + phy-handle = <&ext_rgmii_phy>; + phy-supply = <®_gmac_2v5>; + allwinner,rx-delay-ps = <1500>; + allwinner,tx-delay-ps = <700>; + status = "okay"; +}; + &hdmi { ddc-supply = <®_ddc>; status = "okay"; @@ -93,6 +126,17 @@ }; }; +&mdio { + ext_rgmii_phy: ethernet-phy@1 { + compatible = "ethernet-phy-ieee802.3-c22"; + reg = <1>; + + reset-gpios = <&pio 3 14 GPIO_ACTIVE_LOW>; /* PD14 */ + reset-assert-us = <15000>; + reset-deassert-us = <40000>; + }; +}; + &mmc0 { pinctrl-names = "default"; pinctrl-0 = <&mmc0_pins>; -- 2.21.0 _______________________________________________ dri-devel mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/dri-devel
