On Wed, Jun 16, 2021 at 11:37 AM Matthew Joyce <mfjoyce2...@gmail.com> wrote:
> I hate to ask, but where should the build binaries be if "make all" > was actually successful? > For newlib, there should be various libc.a and libm.a files in the build directory. Use find to locate them: find . -name libc.a And use "nm" to find out if the symbol is there. sparc-rtems6-nm .../libc.a You can save that output or pipe it to less. Note: paths need to be adjusted to the files. --joel > > Thanks! > > Matt > > On Wed, Jun 16, 2021 at 6:16 PM Eshan Dhawan <eshandhawa...@gmail.com> > wrote: > > > > Hi Matt, > > > On 16-Jun-2021, at 9:27 PM, Matthew Joyce <mfjoyce2...@gmail.com> > wrote: > > > > > > Hi Dr. Joel, > > > > > > I tried that in newlib/libc and there were at least no errors. > > > (Nothing leading me to believe it was successful either!) > > > > > > However I still got the same error when I sudo make install. > > > (sparc-rtems-ranlib: command not found) (among others!) > > > > > I make works then there is no need to run make install it just copies > the build binaries to the root folders. > > > > If make is build with the changes u made and the symbols that you added > appear in the binaries you generated. > > Then congratulations :) > > Now you just need to test those changes in the RSB to test they don’t > break anything in the RTEMS ecosystem. > > > Thanks again! > > > > > > Sincerely, > > > > > > Matt > > > > > > > > > > > >> On Wed, Jun 16, 2021 at 3:06 PM Joel Sherrill <j...@rtems.org> wrote: > > >> > > >> Does adding --no-recursive and running it only from the directory you > touched a build system file in help? > > >> > > >> It is regenerating a lot you don't want to touch anyway. > > >> > > >> --joel > > >> > > >>> On Wed, Jun 16, 2021, 5:32 AM Matthew Joyce <mfjoyce2...@gmail.com> > wrote: > > >>> > > >>> Hi Eshan, > > >>> > > >>> Thanks very much for your follow up! Ok, I see now that if I go into > > >>> development/newlib/newlib-cygwin/newlib and run autoreconf -fvi with > > >>> the v2.69 using the PATH that Dr. Joel just showed, it starts to run. > > >>> It always eventually exits with an error though. (please see attached > > >>> .txt). I hope you can read that...I used the command "script" to > > >>> output everything to a text file. > > >>> > > >>> Do you have any idea where I might be going wrong? > > >>> > > >>> Thank you! > > >>> > > >>> Sincerely, > > >>> > > >>> Matt > > >>> > > >>> On Tue, Jun 15, 2021 at 8:23 PM Eshan Dhawan < > eshandhawa...@gmail.com> wrote: > > >>>> > > >>>> Hi matt > > >>>> It would work if run inside newlib instead of newlib-cygwin > > >>>> run command inside of ../newlib-cygwin/newlib > > >>>> instead of ../newlib-cygwin > > >>>> > > >>>> > > >>>> On Tue, Jun 15, 2021 at 10:59 PM Matthew Joyce < > mfjoyce2...@gmail.com> wrote: > > >>>>> > > >>>>> Ah, ok will do! Thank you for the tip. > > >>>>> > > >>>>> On Tue, Jun 15, 2021 at 7:17 PM Gedare Bloom <ged...@rtems.org> > wrote: > > >>>>>> > > >>>>>> Just a note, it's more efficient to capture your terminal dump > into a > > >>>>>> text file and attach that, rather than put a screenshot up. > > >>>>>> > > >>>>>> On Tue, Jun 15, 2021 at 11:14 AM Matthew Joyce < > mfjoyce2...@gmail.com> wrote: > > >>>>>>> > > >>>>>>> Hi Gentlemen, > > >>>>>>> > > >>>>>>> Thanks very much for your quick replies! > > >>>>>>> > > >>>>>>> I just tried both, but perhaps I'm misinterpreting your > suggestions. > > >>>>>>> (Could you please see the attached commands / errors!) > > >>>>>>> > > >>>>>>> Eshan, > > >>>>>>> > > >>>>>>> I did see that link, but it wasn't clear to me what the solution > was...Sorry! > > >>>>>>> > > >>>>>>> Sincerely, > > >>>>>>> > > >>>>>>> Matt > > >>>>>>> > > >>>>>>> On Tue, Jun 15, 2021 at 6:52 PM Eshan Dhawan < > eshandhawa...@gmail.com> wrote: > > >>>>>>>> > > >>>>>>>> Hi Matt, > > >>>>>>>> Try running the command with autoconf version 2.69 that's > shipped with RTEMS in the rtems bin > > >>>>>>>> That works as well. > > >>>>>>>> > > >>>>>>>> Also From a quick google search this is what I found : > https://superuser.com/questions/617872/cant-locate-autom4te-channeldefs-pm-in-inc-when-it-definitely-is-there > > >>>>>>>> > > >>>>>>>> On Tue, Jun 15, 2021 at 9:12 PM Matthew Joyce < > mfjoyce2...@gmail.com> wrote: > > >>>>>>>>> > > >>>>>>>>> Hello Dr. Joel and Eshan, > > >>>>>>>>> > > >>>>>>>>> I have a patch ready to send to Newlib for the sig function > prototypes > > >>>>>>>>> and STR2SIG_MAX. > > >>>>>>>>> > > >>>>>>>>> But to do that, I think I need to have Newlib built, which I > must > > >>>>>>>>> still be doing wrong. The error that I am getting is attached > below. > > >>>>>>>>> > > >>>>>>>>> I’ve been trying to follow the steps here: > > >>>>>>>>> > https://medium.com/my-gsoc-2019-journey/apply-newlib-patch-to-rtems-source-builder-6873b0fb31b8 > > >>>>>>>>> and > https://medium.com/my-gsoc-2019-journey/build-newlib-for-sparc-and-arm-architecture-6b3287d4c6f2 > > >>>>>>>>> > > >>>>>>>>> I even had rebuilt everything from scratch to see if that > would help, > > >>>>>>>>> but I still get the same error. Maybe I cloned the newlib > source into > > >>>>>>>>> the wrong directory? > > >>>>>>>>> > > >>>>>>>>> I was hoping to get the patch off to Newlib for review as a > first step > > >>>>>>>>> while I work on writing the actual methods. When you get a > moment, > > >>>>>>>>> could you please advise? Thank you very much! > > >>>>>>>>> > > >>>>>>>>> Sincerely, > > >>>>>>>>> > > >>>>>>>>> Matt > > >>>>>>> _______________________________________________ > > >>>>>>> devel mailing list > > >>>>>>> devel@rtems.org > > >>>>>>> http://lists.rtems.org/mailman/listinfo/devel >
_______________________________________________ devel mailing list devel@rtems.org http://lists.rtems.org/mailman/listinfo/devel
