Hi Matt, > On 16-Jun-2021, at 9:27 PM, Matthew Joyce <mfjoyce2...@gmail.com> wrote: > > Hi Dr. Joel, > > I tried that in newlib/libc and there were at least no errors. > (Nothing leading me to believe it was successful either!) > > However I still got the same error when I sudo make install. > (sparc-rtems-ranlib: command not found) (among others!) > I make works then there is no need to run make install it just copies the build binaries to the root folders.
If make is build with the changes u made and the symbols that you added appear in the binaries you generated. Then congratulations :) Now you just need to test those changes in the RSB to test they don’t break anything in the RTEMS ecosystem. > Thanks again! > > Sincerely, > > Matt > > > >> On Wed, Jun 16, 2021 at 3:06 PM Joel Sherrill <j...@rtems.org> wrote: >> >> Does adding --no-recursive and running it only from the directory you >> touched a build system file in help? >> >> It is regenerating a lot you don't want to touch anyway. >> >> --joel >> >>> On Wed, Jun 16, 2021, 5:32 AM Matthew Joyce <mfjoyce2...@gmail.com> wrote: >>> >>> Hi Eshan, >>> >>> Thanks very much for your follow up! Ok, I see now that if I go into >>> development/newlib/newlib-cygwin/newlib and run autoreconf -fvi with >>> the v2.69 using the PATH that Dr. Joel just showed, it starts to run. >>> It always eventually exits with an error though. (please see attached >>> .txt). I hope you can read that...I used the command "script" to >>> output everything to a text file. >>> >>> Do you have any idea where I might be going wrong? >>> >>> Thank you! >>> >>> Sincerely, >>> >>> Matt >>> >>> On Tue, Jun 15, 2021 at 8:23 PM Eshan Dhawan <eshandhawa...@gmail.com> >>> wrote: >>>> >>>> Hi matt >>>> It would work if run inside newlib instead of newlib-cygwin >>>> run command inside of ../newlib-cygwin/newlib >>>> instead of ../newlib-cygwin >>>> >>>> >>>> On Tue, Jun 15, 2021 at 10:59 PM Matthew Joyce <mfjoyce2...@gmail.com> >>>> wrote: >>>>> >>>>> Ah, ok will do! Thank you for the tip. >>>>> >>>>> On Tue, Jun 15, 2021 at 7:17 PM Gedare Bloom <ged...@rtems.org> wrote: >>>>>> >>>>>> Just a note, it's more efficient to capture your terminal dump into a >>>>>> text file and attach that, rather than put a screenshot up. >>>>>> >>>>>> On Tue, Jun 15, 2021 at 11:14 AM Matthew Joyce <mfjoyce2...@gmail.com> >>>>>> wrote: >>>>>>> >>>>>>> Hi Gentlemen, >>>>>>> >>>>>>> Thanks very much for your quick replies! >>>>>>> >>>>>>> I just tried both, but perhaps I'm misinterpreting your suggestions. >>>>>>> (Could you please see the attached commands / errors!) >>>>>>> >>>>>>> Eshan, >>>>>>> >>>>>>> I did see that link, but it wasn't clear to me what the solution >>>>>>> was...Sorry! >>>>>>> >>>>>>> Sincerely, >>>>>>> >>>>>>> Matt >>>>>>> >>>>>>> On Tue, Jun 15, 2021 at 6:52 PM Eshan Dhawan <eshandhawa...@gmail.com> >>>>>>> wrote: >>>>>>>> >>>>>>>> Hi Matt, >>>>>>>> Try running the command with autoconf version 2.69 that's shipped with >>>>>>>> RTEMS in the rtems bin >>>>>>>> That works as well. >>>>>>>> >>>>>>>> Also From a quick google search this is what I found : >>>>>>>> https://superuser.com/questions/617872/cant-locate-autom4te-channeldefs-pm-in-inc-when-it-definitely-is-there >>>>>>>> >>>>>>>> On Tue, Jun 15, 2021 at 9:12 PM Matthew Joyce <mfjoyce2...@gmail.com> >>>>>>>> wrote: >>>>>>>>> >>>>>>>>> Hello Dr. Joel and Eshan, >>>>>>>>> >>>>>>>>> I have a patch ready to send to Newlib for the sig function prototypes >>>>>>>>> and STR2SIG_MAX. >>>>>>>>> >>>>>>>>> But to do that, I think I need to have Newlib built, which I must >>>>>>>>> still be doing wrong. The error that I am getting is attached below. >>>>>>>>> >>>>>>>>> I’ve been trying to follow the steps here: >>>>>>>>> https://medium.com/my-gsoc-2019-journey/apply-newlib-patch-to-rtems-source-builder-6873b0fb31b8 >>>>>>>>> and >>>>>>>>> https://medium.com/my-gsoc-2019-journey/build-newlib-for-sparc-and-arm-architecture-6b3287d4c6f2 >>>>>>>>> >>>>>>>>> I even had rebuilt everything from scratch to see if that would help, >>>>>>>>> but I still get the same error. Maybe I cloned the newlib source into >>>>>>>>> the wrong directory? >>>>>>>>> >>>>>>>>> I was hoping to get the patch off to Newlib for review as a first step >>>>>>>>> while I work on writing the actual methods. When you get a moment, >>>>>>>>> could you please advise? Thank you very much! >>>>>>>>> >>>>>>>>> Sincerely, >>>>>>>>> >>>>>>>>> Matt >>>>>>> _______________________________________________ >>>>>>> devel mailing list >>>>>>> devel@rtems.org >>>>>>> http://lists.rtems.org/mailman/listinfo/devel _______________________________________________ devel mailing list devel@rtems.org http://lists.rtems.org/mailman/listinfo/devel
