PS: how do you get the repo inlined to the [PATCH xxx] subject line? It's handy.
On Thu, Apr 2, 2020 at 8:51 AM Gedare Bloom <ged...@rtems.org> wrote:
>
> On Thu, Apr 2, 2020 at 8:43 AM Christian Mauderer
> <christian.maude...@embedded-brains.de> wrote:
> >
> > Update #3869
> > ---
> > user/bsps/arm/imx.rst | 49
> > ++++++++++++++++++++++++++++++++++++++++++++++---
> > 1 file changed, 46 insertions(+), 3 deletions(-)
> >
> > diff --git a/user/bsps/arm/imx.rst b/user/bsps/arm/imx.rst
> > index bc93ae3..51c3b7e 100644
> > --- a/user/bsps/arm/imx.rst
> > +++ b/user/bsps/arm/imx.rst
> > @@ -7,9 +7,10 @@ imx (NXP i.MX)
> > ==============
> >
> > This BSP offers only one variant, the `imx7`. This variant supports the
> > i.MX
> > -7Dual processor. The basic hardware initialization is not performed by the
> > -BSP. A boot loader with device tree support must be used to start the BSP,
> > -e.g. U-Boot.
> > +7Dual processor and the i.MX 6UL/ULL processor family (with slightly
> > different
> > +clock settings). The basic hardware initialization is not performed by
> > the BSP.
> > +A boot loader with device tree support must be used to start the BSP, e.g.
> > +U-Boot or barebox.
> >
> > Build Configuration Options
> > ---------------------------
> > @@ -40,9 +41,30 @@ The following options are available at the configure
> > command line.
> > ``IMX_CCM_UART_HZ``
> > The UART clock frequency in Hz (default is 24000000).
> >
> > +``IMX_CCM_ECSPI_HZ``
> > + The ECSPI clock frequency in Hz (default is 67500000).
> > +
> > ``IMX_CCM_AHB_HZ``
> > The AHB clock frequency in Hz (default is 135000000).
> >
> > +``IMX_CCM_SDHCI_HZ``
> > + The SDHCI clock frequency in Hz (default is 196363000).
> > +
> > +Clock settings for different boards
> > +-----------------------------------
> > +
> > +The default clock settings are targeted for an i.MX 7Dual evaluation board
> > using
> > +U-Boot. Some other boards with different boot loaders need different
> > settings:
> > +
> > + * Phytec phyCORE-i.MX 6ULL (system on module) with MCIMX6Y2CVM08AB and a
> > + barebox bootloader (version ``2019.01.0-bsp-yocto-i.mx6ul-pd19.1.0``):
> > +
> > + * IMX_CCM_IPG_HZ=66000000
> > + * IMX_CCM_UART_HZ=80000000
> > + * IMX_CCM_AHB_HZ=66000000
> > + * IMX_CCM_SDHCI_HZ=198000000
> > + * IMX_CCM_ECSPI_HZ=60000000
> > +
> > Boot via U-Boot
> > ---------------
> >
> > @@ -65,6 +87,14 @@ The ``loadfdt`` command may be not defined in your
> > U-Boot environment. Just
> > replace it with the appropriate commands to load the device tree at
> > ``${fdt_addr}``.
> >
> > +Boot via barebox
> > +----------------
> > +
> > +The same command like for U-Boot can be used to generate an application
> > image.
> > +In a default configuration barebox expects an fdt image called `oftree`
> > and a
> > +kernel image called `zImage` in the root folder of the bootable medium
> > (e.g. an
> > +SD card).
> > +
> > Clock Driver
> > ------------
> >
> > @@ -133,6 +163,18 @@ system controls:
> > A value of zero for the time or count disables the interrupt coalescing in
> > the
> > corresponding direction.
> >
> > +On the Phytec phyCORE-i.MX 6ULL modules the PHY needs an initialization
> > for the
> > +clock. A special PHY driver handles that (``ksz8091rnb``). Add it to your
> > libbsd
> > +config like that:
> > +
> > +.. code-block:: c
> > +
> > + #define RTEMS_BSD_CONFIG_BSP_CONFIG
> > + #define RTEMS_BSD_CONFIG_INIT
> > + SYSINIT_DRIVER_REFERENCE(ksz8091rnb, miibus);
> > + #include <machine/rtems-bsd-config.h>
> > +
> > +
> Is the extra space needed here?
>
> > MMC/SDCard Driver
> > -----------------
> >
> > @@ -147,3 +189,4 @@ Caveats
> > The clock and pin configuration support is quite rudimentary and mostly
> > relies
> > on the boot loader. For a pin group configuration see
> > ``imx_iomux_configure_pins()``. There is no power management support.
> > +
>
> Many docs end without the blank line. It does cause git to complain.
> I'm not sure if we have any rule about it for writing docs.
>
> > --
> > 2.16.4
> >
> > _______________________________________________
> > devel mailing list
> > devel@rtems.org
> > http://lists.rtems.org/mailman/listinfo/devel
_______________________________________________
devel mailing list
devel@rtems.org
http://lists.rtems.org/mailman/listinfo/devel
