> >I can't kill X and can't even ssh into my box from another box. > >Using Debian 3.0 kernel-2.4.18-bf2.4 > >I have read that burners need to be the master device. > >So the HP burner is master on IDE2. I don't know what the deal is. > >Whenever I start xcdroast and/or mount the burner to look at a cd, > >I freeze up HARD. I have installed cdrecord and xcdroast. > >Here is all the relevant information I can think of: > > > >andy# cdrecord -scanbus > >Cdrecord 1.10 (i686-pc-linux-gnu) Copyright (C) 1995-2001 Jörg Schilling > >Linux sg driver version: 3.1.22 > >Using libscg version 'schily-0.5' > >scsibus0: > > 0,0,0 0) 'HP ' 'CD-Writer+ 8200 ' '1.0f' Removable CD-ROM > > 0,1,0 1) * > > 0,2,0 2) * > > 0,3,0 3) * > > 0,4,0 4) * > > 0,5,0 5) * > > 0,6,0 6) * > > 0,7,0 7) * > > > >Here is relevant info from dmesg: > >Uniform Multi-Platform E-IDE driver Revision: 6.31 > >ide: Assuming 33MHz system bus speed for PIO modes; override with > > idebus=xx ServerWorks CSB5: IDE controller on PCI bus 00 dev 79 > >ServerWorks CSB5: chipset revision 146 > >ServerWorks CSB5: not 100% native mode: will probe irqs later > > ide0: BM-DMA at 0x08b0-0x08b7, BIOS settings: hda:DMA, hdb:pio > > ide1: BM-DMA at 0x08b8-0x08bf, BIOS settings: hdc:DMA, hdd:pio > >hda: WDC WD200BB-18DEA0, ATA DISK drive > >hdb: MAXTOR 6L080L4, ATA DISK drive > >hdc: Hewlett-Packard CD-Writer Plus 8200, ATAPI CD/DVD-ROM drive > >hdd: GCR-8481B, ATAPI CD/DVD-ROM drive > >ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 > >ide1 at 0x170-0x177,0x376 on irq 15 > >hda: 39062500 sectors (20000 MB) w/2048KiB Cache, CHS=2431/255/63, > > UDMA(100) hdb: 156355584 sectors (80054 MB) w/1819KiB Cache, > > CHS=155114/16/63, UDMA(100) hdd: ATAPI 48X CD-ROM drive, 128kB Cache, > > UDMA(33) > >Uniform CD-ROM driver Revision: 3.12 > ><snip> > >scsi0 : SCSI host adapter emulation for IDE ATAPI devices > > Vendor: HP Model: CD-Writer+ 8200 Rev: 1.0f > > Type: CD-ROM ANSI SCSI revision: 02 > >Attached scsi CD-ROM sr0 at scsi0, channel 0, id 0, lun 0 > >sr0: scsi3-mmc drive: 8x/24x writer cd/rw xa/form2 cdda tray > > > >andy# ls -al /dev/cd* > >lrwxrwxrwx 1 root root 3 Mar 6 13:07 /dev/cdrom -> hdd > >lrwxrwxrwx 1 root root 4 Mar 6 11:29 /dev/cdrw -> scd0 > >brw-rw---- 1 root cdrom 24, 0 Mar 14 2002 /dev/cdu535 > > > >andy# cat /etc/modules > >ide-scsi > >eepro100 > >radeon > >usb-ohci > >input > >usbkbd > >keybdev > >emu10k1 > > > >This was added to lilo.conf: > >append="hdc=ide-scsi" > > > >andy# cat /etc/default/cdrecord > >CDR_DEVICE=hp > >CDR_SPEED=4 > >CDR_FIFOSIZE=4m > >teac= 1,3,0 -1 -1 "" > >panasonic= 1,4,0 -1 -1 "" > >plextor= 1,4,0 12 -1 "" > >sanyo= 1,4,0 12 -1 burnproof > >yamaha= 1,5,0 -1 -1 "" > >cdrom= 0,6,0 2 1m "" > > > >This is in /etc/fstab: > >/dev/cdrom /cdrom iso9660 ro,user,noauto 0 0 > >/dev/cdrw /cdrw iso9660 ro,user,noauto 0 0 > > > >That is all I can think of for details. There is no info in messages > >or syslog on my lockups. > >Am I missing a module?? ----------------------------- On Thursday 06 March 2003 15:53, Brad wrote: > Andy, > > First of all, I don't think the 2.4.18-bf2.4 kernel has all the modules > you need for scsi-emulation. Find out for sure, and update ur kernel if > necissary (apt-get) (or u can compile ur own with the below modules). > Once you have done that, try the following (along with what you already > have done) to get it working. > > This worked for me: > > 1) Add the following to the end of /etc/modules.conf > > options ide-cd ignore=hdc # tell the ide-cd module to > ignore hdb > alias scd0 sr_mod # load sr_mod upon access of scd0 > pre-install sg modprobe ide-scsi # load ide-scsi before sg > pre-install sr_mod modprobe ide-scsi # load ide-scsi before sr_mod > pre-install ide-scsi modprobe ide-cd # load ide-cd before ide-scsi > > 2) Add the following the following to /etc/modules > > ide-scsi #You should have this already, if the 'modules' file you > quoted was correct > sg > > note: 'scsi_mod' and 'ide-cd' should be loaded too. ----------------------------------------
I have put all that in modules.conf by way of update-modules. My computer still locks up HARD whenever I do xcdroast. This really sucks as I have locked up my machine about 15 times now. I recompiled my kernel a few times to get everything modularized. andy# lsmod Module Size Used by Not tainted sg 24452 0 sr_mod 12088 0 (unused) <bunch of stuff snipped> ide-scsi 7488 0 ide-cd 26336 0 cdrom 28832 0 [sr_mod ide-cd] scsi_mod 50652 3 [sg sr_mod ide-scsi] Now if I do a command line cdrecord, I get this error (but at least I don't lock up my whole machine!) teelhead:/home/andy# cdrecord -speed=1 dev=0,0,0 -data paperport.iso Cdrecord 1.10 (i686-pc-linux-gnu) Copyright (C) 1995-2001 Jörg Schilling scsidev: '0,0,0' scsibus: 0 target: 0 lun: 0 Linux sg driver version: 3.1.22 Using libscg version 'schily-0.5' Device type : Removable CD-ROM Version : 0 Response Format: 1 Vendor_info : 'HP ' Identifikation : 'CD-Writer+ 8200 ' Revision : '1.0f' Device seems to be: Generic mmc CD-RW. Using generic SCSI-3/mmc CD-R driver (mmc_cdr). Driver flags : SWABAUDIO cdrecord: Drive needs to reload the media to return to proper status. Starting to write CD/DVD at speed 2 in write mode for single session. Last chance to quit, starting real write in 0 seconds. Operation starts. cdrecord: Input/output error. read track info: scsi sendcmd: no error CDB: 52 01 00 00 00 FF 00 00 1C 00 status: 0x2 (CHECK CONDITION) Sense Bytes: 70 00 05 00 00 00 00 12 00 00 00 00 24 00 00 C0 Sense Key: 0x5 Illegal Request, Segment 0 Sense Code: 0x24 Qual 0x00 (invalid field in cdb) Fru 0x0 Sense flags: Blk 0 (not valid) error refers to command part, bit ptr 0 (not valid) field ptr 0 cmd finished after 0.002s timeout 240s Any tips, comments......just about anything would be welcome at this point. Andy -- To UNSUBSCRIBE, email to [EMAIL PROTECTED] with a subject of "unsubscribe". Trouble? Contact [EMAIL PROTECTED]
