Please CC me on all replies, since I'm not currently subscribed to the
list.
I just got a netgear ma311 wireless network card and, after compiling
a 2.4.20 kernel with the necessary hermes PCI/PCMCIA drivers (and just
about every other wireless driver I could find, for that matter), I
got my testing system to recognize it. However, I can't get it
to actually do anything useful (I'm using my 3com wired card to post
this). pump hangs whenever I run it with -i eth1 (where eth1 is the
wireless card). Is pump the way to configure it? I wouldn't think it
would be any different from configuring a wired network card (???).
I really have no clue what I'm doing, but there're a couple things
that I suspect might be the problem. First of all, after I bought it
and opened the box, I realized that it stated in several places that
it required a PIII and PCI 2.2 (I have a Dell PII 233 that I bought
back in late 1997). I'm not sure when PCI 2.2 came out, but if it's
fairly new, my machine might not support it.
The second thing is what it says when I run iwconfig (the part about
version 14 and v. 15 and things being broken):
# iwconfig
lo no wireless extensions.
eth0 no wireless extensions.
Warning: Driver for device eth1 has been compiled with version 14
of Wireless Extension, while this program is using version 15.
Some things may be broken...
eth1 IEEE 802.11-DS ESSID:"" Nickname:"Prism I"
Mode:Managed Channel:-160 Access Point: 00:00:00:00:00:00
Bit Rate:11Mb/s Tx-Power=15 dBm Sensitivity:1/3
Retry min limit:8 RTS thr:off Fragment thr:off
Encryption key:off
Power Management:off
Link Quality:0/92 Signal level:-68 dBm Noise level:-122
dBm
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:0 Missed beacon:0
I'm not sure what versions are being refered to there. Here's some
more info that might be helpful in troubleshooting:
# dpkg -l wireless-tools inux-wlan-ng
+++-==============-==============-============================================
ii wireless-tools 25-2 Tools for manipulating Linux
Wireless Extens
ii linux-wlan-ng 0.1.15-1 utilities for wireless prism2 cards
and the pertinent dmsg section:
orinoco.c 0.11b (David Gibson <[EMAIL PROTECTED]> and
others)
hermes.c: 5 Apr 2002 David Gibson <[EMAIL PROTECTED]>
orinoco_cs.c 0.11b (David Gibson <[EMAIL PROTECTED]> and
others)
orinoco_plx.c 0.11b (Daniel Barlow <[EMAIL PROTECTED]>)
PCI: Found IRQ 10 for device 00:0d.0
Detected Orinoco/Prism2 PCI device at 00:0d.0, mem:0xF5200000 to
0xF5200FFF -> 0
xce816000, irq:10
Reset done......................................................................
................................................................................
................................................................................
..............;
Clear Reset.....................................................................
................................................................................
................................................................................
................................................................................
................................................................................
................................................................................
...........................;
pci_cor : reg = 0x0 - 21D - 1EB
eth1: Station identity 001f:0006:0001:0003
eth1: Looks like an Intersil firmware version 1.03
eth1: Ad-hoc demo mode supported
eth1: IEEE standard IBSS ad-hoc mode supported
eth1: WEP supported, 104-bit key
eth1: MAC address [MAC address removed by paranoid poster]
eth1: Station name "Prism I"
eth1: ready
Any ideas? Anything at all would probably be helpful.
TIA
--
To UNSUBSCRIBE, email to [EMAIL PROTECTED]
with a subject of "unsubscribe". Trouble? Contact [EMAIL PROTECTED]
