Package: linux-2.6
Version: 3.1.1-1
Justification: renders package unusable
Severity: grave
Dear Maintainer,
At present, I use a Kernel Linux 2.6.39-2-686-pae and I have just installed a
kernel Linux 3.1.0-1-686-pae.
Just after entering in runlevel S, kernel Linux 3.1.0-1-686-pae switch on too
high video mode for my old 1024x768 screen (Hyundai ImageQuest L50S), when It
configure video card. Kernel Linux 2.6.39-2-686-pae had always worked fine.
I have tried to force video mode at 1024x768x16 with GRUB_GFXMODE grub's
parameter. I take the same problem.
I suspect a problem with my poulsbo GMA500 Intel chipset.
Regards,
-- File /etc/default/grub
GRUB_DEFAULT=0
GRUB_TIMEOUT=5
GRUB_CMDLINE_LINUX_DEFAULT="quiet"
GRUB_GFXPAYLOAD_LINUX="keep"
GRUB_GFXMODE=1024x768x16
-- Package-specific info:
** Kernel log: boot messages should be attached
** Model information
not available
** PCI devices:
00:00.0 Host bridge [0600]: Intel Corporation System Controller Hub (SCH
Poulsbo) [8086:8100] (rev 07)
Subsystem: Intel Corporation Device [8086:8119]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
00:02.0 VGA compatible controller [0300]: Intel Corporation System Controller
Hub (SCH Poulsbo) Graphics Controller [8086:8108] (rev 07) (prog-if 00 [VGA
controller])
Subsystem: Intel Corporation Device [8086:8119]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 10
Region 0: Memory at fe980000 (32-bit, non-prefetchable) [size=512K]
Region 1: I/O ports at c880 [size=8]
Region 2: Memory at d0000000 (32-bit, non-prefetchable) [size=256M]
Region 3: Memory at fe940000 (32-bit, non-prefetchable) [size=256K]
Expansion ROM at <unassigned> [disabled]
Capabilities: <access denied>
00:1b.0 Audio device [0403]: Intel Corporation System Controller Hub (SCH
Poulsbo) HD Audio Controller [8086:811b] (rev 07)
Subsystem: Intel Corporation Device [8086:8119]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 16
Region 0: Memory at fe938000 (64-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: HDA Intel
00:1c.0 PCI bridge [0604]: Intel Corporation System Controller Hub (SCH
Poulsbo) PCI Express Port 1 [8086:8110] (rev 07) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 0000d000-0000dfff
Memory behind bridge: fea00000-feafffff
Prefetchable memory behind bridge: cff00000-cfffffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:1c.1 PCI bridge [0604]: Intel Corporation System Controller Hub (SCH
Poulsbo) PCI Express Port 2 [8086:8112] (rev 07) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
I/O behind bridge: 0000e000-0000efff
Memory behind bridge: feb00000-febfffff
Prefetchable memory behind bridge: 80000000-801fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:1d.0 USB Controller [0c03]: Intel Corporation System Controller Hub (SCH
Poulsbo) USB UHCI #1 [8086:8114] (rev 07) (prog-if 00 [UHCI])
Subsystem: Intel Corporation Device [8086:8119]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 16
Region 4: I/O ports at c480 [size=32]
Kernel driver in use: uhci_hcd
00:1d.1 USB Controller [0c03]: Intel Corporation System Controller Hub (SCH
Poulsbo) USB UHCI #2 [8086:8115] (rev 07) (prog-if 00 [UHCI])
Subsystem: Intel Corporation Device [8086:8119]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 17
Region 4: I/O ports at c080 [size=32]
Kernel driver in use: uhci_hcd
00:1d.2 USB Controller [0c03]: Intel Corporation System Controller Hub (SCH
Poulsbo) USB UHCI #3 [8086:8116] (rev 07) (prog-if 00 [UHCI])
Subsystem: Intel Corporation Device [8086:8119]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin C routed to IRQ 18
Region 4: I/O ports at b880 [size=32]
Kernel driver in use: uhci_hcd
00:1d.7 USB Controller [0c03]: Intel Corporation System Controller Hub (SCH
Poulsbo) USB EHCI #1 [8086:8117] (rev 07) (prog-if 20 [EHCI])
Subsystem: Intel Corporation Device [8086:8119]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin D routed to IRQ 19
Region 0: Memory at fe937c00 (32-bit, non-prefetchable) [size=1K]
Capabilities: <access denied>
Kernel driver in use: ehci_hcd
00:1f.0 ISA bridge [0601]: Intel Corporation System Controller Hub (SCH
Poulsbo) LPC Bridge [8086:8119] (rev 07)
Subsystem: Intel Corporation System Controller Hub (SCH Poulsbo) LPC
Bridge [8086:8119]
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Kernel driver in use: lpc_sch
00:1f.1 IDE interface [0101]: Intel Corporation System Controller Hub (SCH
Poulsbo) IDE Controller [8086:811a] (rev 07) (prog-if 80 [Master])
Subsystem: Intel Corporation Device [8086:8119]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Region 0: [virtual] Memory at 000001f0 (32-bit, non-prefetchable)
[size=8]
Region 1: [virtual] Memory at 000003f0 (type 3, non-prefetchable)
[size=1]
Region 2: [virtual] Memory at 00000170 (32-bit, non-prefetchable)
[size=8]
Region 3: [virtual] Memory at 00000370 (type 3, non-prefetchable)
[size=1]
Region 4: I/O ports at ffa0 [size=16]
Kernel driver in use: pata_sch
01:00.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd.
RTL8111/8168B PCI Express Gigabit Ethernet controller [10ec:8168] (rev 02)
Subsystem: Realtek Semiconductor Co., Ltd. TEG-ECTX Gigabit PCI-E
Adapter [Trendnet] [10ec:8168]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 40
Region 0: I/O ports at dd00 [size=256]
Region 2: Memory at feaff000 (64-bit, non-prefetchable) [size=4K]
Region 4: Memory at cfff0000 (64-bit, prefetchable) [size=64K]
Expansion ROM at feac0000 [disabled] [size=128K]
Capabilities: <access denied>
Kernel driver in use: r8169
02:00.0 Mass storage controller [0180]: Silicon Image, Inc. SiI 3132 Serial ATA
Raid II Controller [1095:3132] (rev 01)
Subsystem: Silicon Image, Inc. SiI 3132 Serial ATA Raid II Controller
[1095:3132]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 17
Region 0: Memory at febffc00 (64-bit, non-prefetchable) [size=128]
Region 2: Memory at febf8000 (64-bit, non-prefetchable) [size=16K]
Region 4: I/O ports at e880 [size=128]
Expansion ROM at feb00000 [disabled] [size=512K]
Capabilities: <access denied>
Kernel driver in use: sata_sil24
** USB devices:
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 001 Device 003: ID 148f:3070 Ralink Technology, Corp. RT2870/RT3070
Wireless Adapter
Bus 002 Device 002: ID 058f:9254 Alcor Micro Corp. Hub
Bus 002 Device 003: ID 1e54:2030 TypeMatrix 2030 USB Keyboard
Bus 002 Device 004: ID 045e:0040 Microsoft Corp. Wheel Mouse Optical
-- System Information:
Debian Release: wheezy/sid
APT prefers testing
APT policy: (650, 'testing')
Architecture: i386 (i686)
Kernel: Linux 2.6.39-2-686-pae (SMP w/2 CPU cores)
Locale: LANG=fr_FR.UTF-8, LC_CTYPE=fr_FR.UTF-8 (charmap=UTF-8)
Shell: /bin/sh linked to /bin/dash
Versions of packages linux-image-3.1.0-1-686-pae depends on:
ii debconf [debconf-2.0] 1.5.40
ii initramfs-tools [linux-initramfs-tool] 0.99
ii linux-base 3.3
ii module-init-tools 3.16-1
Versions of packages linux-image-3.1.0-1-686-pae recommends:
ii firmware-linux-free 3
ii libc6-i686 2.13-21
Versions of packages linux-image-3.1.0-1-686-pae suggests:
ii grub-pc 1.99-14
ii linux-doc-3.1 3.1.1-1
Versions of packages linux-image-3.1.0-1-686-pae is related to:
pn firmware-bnx2 <none>
pn firmware-bnx2x <none>
pn firmware-ipw2x00 <none>
pn firmware-ivtv <none>
pn firmware-iwlwifi <none>
pn firmware-linux <none>
pn firmware-linux-nonfree <none>
pn firmware-qlogic <none>
pn firmware-ralink 0.34
pn xen-hypervisor <none>
-- debconf information:
linux-image-3.1.0-1-686-pae/prerm/removing-running-kernel-3.1.0-1-686-pae:
true
linux-image-3.1.0-1-686-pae/postinst/missing-firmware-3.1.0-1-686-pae:
linux-image-3.1.0-1-686-pae/postinst/ignoring-ramdisk:
linux-image-3.1.0-1-686-pae/postinst/depmod-error-initrd-3.1.0-1-686-pae:
false
--
To UNSUBSCRIBE, email to debian-bugs-dist-requ...@lists.debian.org
with a subject of "unsubscribe". Trouble? Contact listmas...@lists.debian.org
