Package: b43-fwcutter Version: 1:011-5 Severity: important Lasts updates in Lenny made my Wireless device unusable!
$ lspci -vvv 06:00.0 Network controller: Broadcom Corporation BCM94311MCG wlan mini-PCI (rev 01) Subsystem: Broadcom Corporation Device 0465 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 18 Region 0: Memory at f4300000 (32-bit, non-prefetchable) [size=16K] Capabilities: [40] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=2 PME- Capabilities: [58] Message Signalled Interrupts: Mask- 64bit- Queue=0/0 Enable- Address: 00000000 Data: 0000 Capabilities: [d0] Express (v1) Legacy Endpoint, MSI 00 DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <4us, L1 unlimited ExtTag+ AttnBtn- AttnInd- PwrInd- RBE- FLReset- DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported- RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop- MaxPayload 128 bytes, MaxReadReq 128 bytes DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend- LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s, Latency L0 <4us, L1 <64us ClockPM- Suprise- LLActRep- BwNot- LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+ ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt- Capabilities: [100] Advanced Error Reporting <?> Capabilities: [13c] Virtual Channel <?> Kernel driver in use: b43-pci-bridge Kernel modules: ssb I try install b43-fwcutter, and this package recommend download a driver from internet. I accept this. But after installation, I see in boot time that firmware is try to be loaded from /lib/modules/b43, but b43-fwcutter create in /lib/modules/b43legacy, so I create a symbolic link to it. But now, I see in boot time: b43-phy0 ERROR: YOUR FIRMWARE IS TOO OLD. Firmware from binary drivers older than version 4.x is unsupported. You must upgrade your firmware files. b43-phy0 ERROR: You must go to http://linuxwireless.org/en/users/Drivers/b43#devicefirmware and download the latest firmware (version 4) OK, I go to linuxwireless.org, but is still impossible use my wireless device. Anyone have some idea about what is happening? I using knetworkmanager and Lynksys WAG200G adsl/wireless router (With WPA2-Mixed authentication mode). Best regards, Renato S. Yamane -- System Information: Debian Release: lenny/sid APT prefers testing APT policy: (500, 'testing') Architecture: i386 (i686) Kernel: Linux 2.6.26-1-686 (SMP w/2 CPU cores) Locale: LANG=pt_BR.UTF-8, LC_CTYPE=pt_BR.UTF-8 (charmap=UTF-8) Shell: /bin/sh linked to /bin/bash Versions of packages b43-fwcutter depends on: ii debconf [debconf-2.0] 1.5.22 Debian configuration management sy ii libc6 2.7-13 GNU C Library: Shared libraries ii wget 1.11.4-2 retrieves files from the web Versions of packages b43-fwcutter recommends: ii bzip2 1.0.5-1 high-quality block-sorting file co b43-fwcutter suggests no packages. -- debconf information: * b43-fwcutter/cut_firmware: true -- To UNSUBSCRIBE, email to [EMAIL PROTECTED] with a subject of "unsubscribe". Trouble? Contact [EMAIL PROTECTED]
