Package: linux-2.6
Severity: normal
Hi,
Following up on my previous report #412718. I seem to hit another
problem if I disable ACPI:
Linux version 2.6.18-4-486 (Debian 2.6.18.dfsg.1-11) ([EMAIL PROTECTED]) (gcc
version 4.1.2 20061115 (prerelease) (Debian 4.1.1-21)) #1 Wed Feb 21 15:25:16
UTC 2007
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009dc00 (usable)
BIOS-e820: 000000000009dc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000003ffed040 (usable)
BIOS-e820: 000000003ffed040 - 000000003fff0000 (ACPI data)
BIOS-e820: 000000003fff0000 - 0000000040000000 (reserved)
BIOS-e820: 00000000fec00000 - 0000000100000000 (reserved)
Warning only 896MB will be used.
Use a HIGHMEM enabled kernel.
896MB LOWMEM available.
found SMP MP-table at 0009e140
DMI 2.3 present.
Intel MultiProcessor Specification v1.4
Virtual Wire compatibility mode.
OEM ID: IBM ENSW Product ID: BLADER SMP APIC at: 0xFEE00000
Processor #0 15:2 APIC version 20
Processor #6 15:2 APIC version 20
WARNING: NR_CPUS limit of 1 reached. Processor ignored.
I/O APIC #14 Version 17 at 0xFEC00000.
I/O APIC #13 Version 17 at 0xFEC01000.
I/O APIC #12 Version 17 at 0xFEC02000.
Enabling APIC mode: Flat. Using 3 I/O APICs
Processors: 1
Allocating PCI resources starting at 50000000 (gap: 40000000:bec00000)
Detected 2799.474 MHz processor.
Built 1 zonelists. Total pages: 229376
Kernel command line: vga=normal initrd=debian-installer/i386/initrd.gz --
console=ttyS0,19200 acpi=off BOOT_IMAGE=debian-installer/i386/linux
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 16384 bytes)
Console: colour VGA+ 80x25
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 902088k/917504k available (1502k kernel code, 14808k reserved, 601k
data, 256k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay using timer specific routine.. 5601.63 BogoMIPS (lpj=11203278)
Security Framework v1.0.0 initialized
SELinux: Disabled at boot.
Capability LSM initialized
Mount-cache hash table entries: 512
CPU: Trace cache: 12K uops, L1 D cache: 8K
CPU: L2 cache: 512K
Compat vDSO mapped to ffffe000.
CPU: Intel(R) Xeon(TM) CPU 2.80GHz stepping 09
Checking 'hlt' instruction... OK.
ENABLING IO-APIC IRQs
..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
checking if image is initramfs... it is
Freeing initrd memory: 4225k freed
NET: Registered protocol family 16
EISA bus registered
PCI: PCI BIOS revision 2.10 entry at 0xfd82c, last bus=4
PCI: Using configuration type 1
Setting up standard PCI resources
ACPI: Interpreter disabled.
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI: disabled
PnPBIOS: Scanning system for PnP BIOS support...
PnPBIOS: Found PnP BIOS installation structure at 0xc00fdf90
PnPBIOS: PnP BIOS version 1.0, entry 0xf0000:0x41d5, dseg 0xf0000
PnPBIOS: 16 nodes reported by PnP BIOS; 16 recorded by driver
PCI: Probing PCI hardware
PCI: Ignoring BAR0-3 of IDE controller 0000:00:0f.1
PCI: Discovered peer bus 01
PCI: Discovered peer bus 02
PCI->APIC IRQ transform: 0000:00:01.0[A] -> IRQ 161
PCI->APIC IRQ transform: 0000:00:0f.2[A] -> IRQ 7
PCI->APIC IRQ transform: 0000:01:00.0[A] -> IRQ 129
PCI->APIC IRQ transform: 0000:01:00.1[B] -> IRQ 137
PCI->APIC IRQ transform: 0000:02:02.0[A] -> IRQ 145
PCI->APIC IRQ transform: 0000:02:02.1[B] -> IRQ 153
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
TCP established hash table entries: 131072 (order: 7, 524288 bytes)
TCP bind hash table entries: 65536 (order: 6, 262144 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
audit: initializing netlink socket (disabled)
audit(1172598860.944:1): initialized
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
Initializing Cryptographic API
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
PNPBIOS fault.. attempting recovery.
PnPBIOS: Warning! Your PnP BIOS caused a fatal error. Attempting to continue
PnPBIOS: You may need to reboot with the "pnpbios=off" option to operate stably
PnPBIOS: Check with your vendor for an updated BIOS
PnPBIOS: set_dev_node: unexpected status 0x28
pnp: Failed to activate device 00:02.
serial: probe of 00:02 failed with error -5
00:03: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
PNP: PS/2 Controller [PNP0303,PNP0f13] at 0x60,0x64 irq 1,12
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
mice: PS/2 mouse device common for all mice
EISA: Probing bus 0 at eisa.0
Cannot allocate resource for EISA slot 2
EISA: Detected 0 cards.
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
NET: Registered protocol family 8
NET: Registered protocol family 20
Using IPI Shortcut mode
Freeing unused kernel memory: 256k freed
Time: tsc clocksource has been installed.
usbcore: registered new driver usbfs
usbcore: registered new driver hub
tg3.c:v3.65 (August 07, 2006)
ohci_hcd 0000:00:0f.2: OHCI Host Controller
ohci_hcd 0000:00:0f.2: new USB bus registered, assigned bus number 1
ohci_hcd 0000:00:0f.2: irq 7, io mem 0xfebfe000
eth0: Tigon3 [partno(BCM95704A41) rev 2002 PHY(serdes)] (PCIX:133MHz:64-bit)
10/100/1000BaseT Ethernet 00:0d:60:9c:3b:bc
eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[1] Split[0] WireSpeed[0] TSOcap[0]
eth0: dma_rwctrl[769f4000] dma_mask[64-bit]
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 4 ports detected
eth1: Tigon3 [partno(BCM95704A41) rev 2002 PHY(serdes)] (PCIX:133MHz:64-bit)
10/100/1000BaseT Ethernet 00:0d:60:9c:3b:bd
eth1: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] Split[0] WireSpeed[0] TSOcap[1]
eth1: dma_rwctrl[769f4000] dma_mask[64-bit]
usb 1-4: new full speed USB device using ohci_hcd and address 2
usb 1-4: configuration #1 chosen from 1 choice
hub 1-4:1.0: USB hub found
hub 1-4:1.0: 4 ports detected
usb 1-4.1: new full speed USB device using ohci_hcd and address 3
usb 1-4.1: configuration #1 chosen from 1 choice
usb 1-4.3: new full speed USB device using ohci_hcd and address 4
usb 1-4.3: configuration #1 chosen from 1 choice
usbcore: registered new driver hiddev
input: IBM PPC I/F as /class/input/input0
input: USB HID v1.10 Keyboard [IBM PPC I/F] on usb-0000:00:0f.2-4.1
input: IBM PPC I/F as /class/input/input1
input: USB HID v1.10 Mouse [IBM PPC I/F] on usb-0000:00:0f.2-4.1
input: IBM HIDK/M as /class/input/input2
input: USB HID v1.10 Keyboard [IBM HIDK/M] on usb-0000:00:0f.2-4.3
input: IBM HIDK/M as /class/input/input3
input: USB HID v1.10 Mouse [IBM HIDK/M] on usb-0000:00:0f.2-4.3
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
-- System Information:
Debian Release: 3.1
APT prefers unstable
APT policy: (50, 'unstable')
Architecture: i386 (i686)
Kernel: Linux 2.6.12-1-k7
Locale: LANG=en_US.UTF-8, LC_CTYPE=en_US.UTF-8 (charmap=UTF-8)
--
To UNSUBSCRIBE, email to [EMAIL PROTECTED]
with a subject of "unsubscribe". Trouble? Contact [EMAIL PROTECTED]
