Bug#395010: k3b: failure to write audio cdr's

[operator]

thank You very much for Your help. most reciently, it has also stopped writing data to cdrw's, so I can't backup my data. here is the data: Devices ----------------------- QSI CDRW/DVD SBW-242 UX02 (/dev/hdc, ) at /media/cdrom0 [CD-R; CD-RW; CD-ROM; DVD-ROM] [DVD-ROM; CD-ROM; CD-R; CD-RW] [SAO; TAO; RAW; SAO/R16; RAW/R96P; RAW/R96R] System ----------------------- K3b Version: 0.11.20 KDE Version: 3.3.2 QT Version:  3.3.4 Kernel:      2.4.27-2-386 cdrecord ----------------------- scsidev: 'ATAPI:/dev/hdc' devname: 'ATAPI:/dev/hdc' scsibus: -2 target: -2 lun: -2 Warning: Using ATA Packet interface. Warning: The related Linux kernel interface code seems to be unmaintained. Warning: There is absolutely NO DMA, operations thus are slow. SCSI buffer size: 64512 Cdrecord-Clone 2.01.01a01 (i686-pc-linux-gnu) Copyright (C) 1995-2004 Jörg Schilling NOTE: this version of cdrecord is an inofficial (modified) release of cdrecord       and thus may have bugs that are not present in the original version.       Please send bug reports and support requests to <[EMAIL PROTECTED]>.       The original author should not be bothered with problems of this version. TOC Type: 0 = CD-DA Using libscg version 'schily-0.8'. Driveropts: 'burnfree' atapi: 1 Device type    : Removable CD-ROM Version        : 0 Response Format: 2 Capabilities   : Vendor_info    : 'QSI     ' Identifikation : 'CDRW/DVD SBW-242' Revision       : 'UX02' Device seems to be: Generic mmc2 DVD-ROM. Current: 0x0009 Profile: 0x0010 Profile: 0x0008 Profile: 0x0009 (current) Profile: 0x000A Profile: 0x0002 (current) Using generic SCSI-3/mmc   CD-R/CD-RW driver (mmc_cdr). Driver flags   : MMC-3 SWABAUDIO BURNFREE Supported modes: TAO PACKET SAO SAO/R96P SAO/R96R RAW/R16 RAW/R96P RAW/R96R Drive buf size : 1959936 = 1914 KB FIFO size      : 4194304 = 4096 KB pregap1: -1 Track 01: audio   47 MB (04:41.28) no preemp swab copy Track 02: audio   67 MB (06:41.76) no preemp swab copy Track 03: audio   59 MB (05:55.89) no preemp swab copy Track 04: audio   48 MB (04:51.16) no preemp swab copy Track 05: audio   33 MB (03:20.52) no preemp swab copy Total size:      257 MB (25:30.61) = 114796 sectors Lout start:      257 MB (25:32/46) = 114796 sectors Current Secsize: 2048 ATIP info from disk:   Indicated writing power: 5   Is not unrestricted   Is not erasable   Disk sub type: Medium Type A, high Beta category (A+) (3)   ATIP start of lead in:  -11634 (97:26/66)   ATIP start of lead out: 359846 (79:59/71) Disk type:    Short strategy type (Phthalocyanine or similar) Manuf. index: 3 Manufacturer: CMC Magnetics Corporation Blocks total: 359846 Blocks current: 359846 Blocks remaining: 245050 Starting to write CD/DVD at speed 24 in real SAO mode for single session. Last chance to quit, starting real write in 2 seconds.    1 seconds.    0 seconds. Operation starts. Waiting for reader process to fill input buffer ... input buffer ready. BURN-Free is OFF. Turning BURN-Free on Performing OPC... Sending CUE sheet... /usr/bin/cdrecord: WARNING: Drive returns wrong startsec (0) using -150 Writing pregap for track 1 at -150 Starting new track at sector: 0 Track 01:    0 of   47 MB written. Track 01:    1 of   47 MB written (fifo  96%) [buf  87%]   2.3x. /usr/bin/cdrecord: Input/output error. write_g1: scsi sendcmd: no error CDB:  2A 00 00 00 02 1C 00 00 1B 00 status: 0x0 (GOOD STATUS) cmd finished after 10.043s timeout 200s /usr/bin/cdrecord: A write error occured. /usr/bin/cdrecord: Please properly read the error message above. cdrecord comand: ----------------------- /usr/bin/cdrecord.mmap -v gracetime=2 dev=ATAPI:/dev/hdc speed=24 -dao driveropts=burnfree -eject -overburn -useinfo -pad -shorttrack -audio /tmp/kde-root/k3b_audio_0_01.inf /tmp/kde-root/k3b_audio_0_02.inf /tmp/kde-root/k3b_audio_0_03.inf /tmp/kde-root/k3b_audio_0_04.inf /tmp/kde-root/k3b_audio_0_05.inf Thank You very much for Your help Francois, I really appreciate it very much. operator Francois Marier wrote: Would it be possible for you to attach the log from K3b? I think there is a button called "debugging output" or something like that in the window that pops up when the burning process starts. Francois