Package: wodim Version: 5:1.0~pre4-1.1 Severity: normal I've tried to burn a cdrom using wodim, but I get an error almost right away or after burning for a short while. This burner has worked fine with earlier versions of cdrecord for a couple of months ago when I last used it.
I tried to compile the last version of the old cdrecord, but there seems to be problem with that also, could also be that xcdroast gives wodim specific parameters, I don't know. The same problem occurred on an i386-based laptop so I don't think it is a hardware problem, even if wodim/cdrecord tells me so. I've tried with different discs and different iso-files. Here is the debug output: Calling: /usr/lib/xcdroast/bin/xcdrwrap CDRECORD dev= "/dev/hdc" gracetime=2 fs=4096k driveropts=burnfree -v -useinfo speed=0 -dao -eject -pad -data "/n/debian_cd/grml_0.6.iso" ... This is wodim, not cdrecord. Don't expect it to behave like cdrecord in any way, don't refer to it as "cdrecord". Send problem reports to [EMAIL PROTECTED], don't bother Joerg Schilling with any problems caused by this application. Copyright (C) 2006 cdrkit maintainers, (C) 1994-2006 Joerg Schilling scsidev: '/dev/hdc' devname: '/dev/hdc' scsibus: -2 target: -2 lun: -2 Linux sg driver version: 3.5.27 cdrecord: Warning: using inofficial version of libscg (debburn project-0.8ubuntu1+debburn1 '@(#)scsitransp.c 1.91 04/06/17 Copyright 1988,1995,2000-2004 J. Schilling'). cdrecord: Warning: using inofficial libscg transport code version (cdrkit-team-scsi-linux-sg.c-1.86 '@(#)scsi-linux-sg.c 1.86 05/11/22 Copyright 1997 J. Schilling'). SCSI buffer size: 64512 TOC Type: 1 = CD-ROM cdrecord: Success. read buffer: scsi sendcmd: no error CDB: 3C 00 00 00 00 00 00 FC 00 00 Warning: This version of libscg has not been configured via the standard status: 0x2 (CHECK CONDITION) autoconfiguration method of the Schily makefile system. There is a high risk Sense Bytes: 70 00 04 00 00 00 00 0E 00 00 00 00 08 03 00 00 that the code is not configured correctly and for this reason will not behave Sense Key: 0x4 Hardware Error, Segment 0 as expected. Sense Code: 0x08 Qual 0x03 (logical unit communication crc error (ultra-dma/32)) Fru 0x0 Driveropts: 'burnfree' Sense flags: Blk 0 (not valid) atapi: 1 resid: 64512 Device type : Removable CD-ROM cmd finished after 0.001s timeout 200s Version : 0 Response Format: 2 Capabilities : Vendor_info : 'HL-DT-ST' Identifikation : 'DVDRRW GSA-4166B' Revision : '1.01' Device seems to be: Generic mmc2 DVD-R/DVD-RW. Current: 0x0009 Profile: 0x0012 Profile: 0x002B Profile: 0x001B Profile: 0x001A Profile: 0x0015 Profile: 0x0014 Profile: 0x0013 Profile: 0x0011 Profile: 0x0010 Profile: 0x000A Profile: 0x0009 (current) Profile: 0x0008 Profile: 0x0002 Using generic SCSI-3/mmc CD-R/CD-RW driver (mmc_cdr). Driver flags : MMC-3 SWABAUDIO BURNFREE Supported modes: TAO PACKET SAO SAO/R96P SAO/R96R RAW/R16 RAW/R96P RAW/R96R Drive buf size : 1114112 = 1088 KB FIFO size : 4194304 = 4096 KB Track 01: data 700 MB padsize: 30 KB Total size: 804 MB (79:39.86) = 358490 sectors Lout start: 804 MB (79:41/65) = 358490 sectors Current Secsize: 2048 ATIP info from disk: Indicated writing power: 5 Is not unrestricted Is not erasable Disk sub type: Medium Type B, low Beta category (B-) (4) ATIP start of lead in: -12520 (97:15/05) ATIP start of lead out: 359849 (79:59/74) Disk type: Short strategy type (Phthalocyanine or similar) Manuf. index: 26 Manufacturer: TDK Corporation Blocks total: 359849 Blocks current: 359849 Blocks remaining: 1359 Speed set to 2822 KB/s Starting to write CD/DVD at speed 16.0 in real SAO mode for single session. Waiting for reader process to fill input buffer ... input buffer ready. trackno=0 BURN-Free is ON. Performing OPC... Sending CUE sheet... cdrecord: WARNING: Drive returns wrong startsec (0) using -150 Writing pregap for track 1 at -150 Starting new track at sector: 0 cdrecord: Success. write_g1: scsi sendcmd: no error CDB: 2A 00 00 00 00 1F 00 00 1F 00 status: 0x2 (CHECK CONDITION) Sense Bytes: 70 00 04 00 00 00 00 0E 00 00 00 00 08 03 00 00 Sense Key: 0x4 Hardware Error, Segment 0 Sense Code: 0x08 Qual 0x03 (logical unit communication crc error (ultra-dma/32)) Fru 0x0 Sense flags: Blk 0 (not valid) resid: 63488 cmd finished after 0.003s timeout 200s cdrecord: A write error occured. cdrecord: Please properly read the error message above. write track data: error after 63488 bytes Writing time: 11.644s Average write speed 411.6x. Fixating... Fixating time: 0.012s -- System Information: Debian Release: testing/unstable APT prefers unstable APT policy: (500, 'unstable') Architecture: amd64 (x86_64) Shell: /bin/sh linked to /bin/bash Kernel: Linux 2.6.16-1-amd64-k8-smp Locale: LANG=C, LC_CTYPE=en_US.UTF-8 (charmap=UTF-8) Versions of packages wodim depends on: ii libc6 2.3.6.ds1-5 GNU C Library: Shared libraries ii libcap1 1:1.10-14 support for getting/setting POSIX. Versions of packages wodim recommends: ii mkisofs 5:1.0~pre4-1.1 Creates ISO-9660 CD-ROM filesystem -- no debconf information -- To UNSUBSCRIBE, email to [EMAIL PROTECTED] with a subject of "unsubscribe". Trouble? Contact [EMAIL PROTECTED]
