Package: src:linux
Version: 3.2.51-1
Severity: important
Hi,
when copiyng files to pen drive, the process hangs, and then the kernel issues
the messages shown below. I have to remove the pen drive and retry.
It happened more than once. I executed sync in parallel with the copy process.
Regards.
-- Package-specific info:
** Version:
Linux version 3.2.0-4-amd64 (debian-ker...@lists.debian.org) (gcc version 4.6.3
(Debian 4.6.3-14) ) #1 SMP Debian 3.2.51-1
** Command line:
BOOT_IMAGE=/boot/vmlinuz-3.2.0-4-amd64
root=UUID=e2ae9235-faee-430f-9a8f-823c77838a40 ro quiet
** Tainted: WO (4608)
* Taint on warning.
* Out-of-tree module has been loaded.
** Kernel log:
[15453.491317] scsi 7:0:0:0: Direct-Access Kingston DataTraveler 2.0 PMAP
PQ: 0 ANSI: 0 CCS
[15453.492117] sd 7:0:0:0: Attached scsi generic sg2 type 0
[15454.285751] sd 7:0:0:0: [sdb] 15874048 512-byte logical blocks: (8.12
GB/7.56 GiB)
[15454.286252] sd 7:0:0:0: [sdb] Write Protect is off
[15454.286256] sd 7:0:0:0: [sdb] Mode Sense: 23 00 00 00
[15454.286742] sd 7:0:0:0: [sdb] No Caching mode page present
[15454.286747] sd 7:0:0:0: [sdb] Assuming drive cache: write through
[15454.290242] sd 7:0:0:0: [sdb] No Caching mode page present
[15454.290246] sd 7:0:0:0: [sdb] Assuming drive cache: write through
[15454.336971] sdb: sdb1 sdb2
[15454.339292] sd 7:0:0:0: [sdb] No Caching mode page present
[15454.339297] sd 7:0:0:0: [sdb] Assuming drive cache: write through
[15454.339300] sd 7:0:0:0: [sdb] Attached SCSI removable disk
[15456.985543] ------------[ cut here ]------------
[15456.985553] WARNING: at /build/linux-rrsxby/linux-3.2.51/block/genhd.c:1574
disk_clear_events+0xb7/0xe3()
[15456.985555] Hardware name: Dell System Inspiron N411Z
[15456.985557] Modules linked in: nbd cbc ecb ppdev lp vmnet(O) parport_pc
parport vsock(O) vmci(O) vmmon(O) cpufreq_conservative bnep rfcomm
cpufreq_userspace cpufreq_stats cpufreq_powersave 8021q binfmt_misc garp stp
uinput nfsd nfs nfs_acl auth_rpcgss fscache lockd sunrpc loop fuse ecryptfs
dm_crypt dm_mod snd_hda_codec_hdmi snd_hda_codec_conexant arc4 usbhid hid
snd_hda_intel snd_hda_codec iwlwifi snd_hwdep snd_pcm snd_page_alloc mac80211
joydev snd_seq snd_seq_device snd_timer i915 drm_kms_helper cfg80211 drm btusb
bluetooth i2c_i801 snd i2c_algo_bit dell_laptop acpi_cpufreq mperf i2c_core
iTCO_wdt iTCO_vendor_support coretemp rfkill soundcore evdev video dcdbas
psmouse dell_wmi ac pcspkr serio_raw sparse_keymap processor button battery
power_supply wmi ext4 crc16 jbd2 mbcache ums_realtek usb_storage sg sr_mod
sd_mod cdrom crc_t10dif crc32c_intel ghash_clmulni_intel xhci_hcd ahci libahci
libata ehci_hcd aesni_intel scsi_mod aes_x86_64 atl1c thermal thermal_sys
aes_generic cryptd
usbcore usb_common [last unloaded: scsi_wait_scan]
[15456.985634] Pid: 26301, comm: hald-probe-volu Tainted: G O
3.2.0-4-amd64 #1 Debian 3.2.51-1
[15456.985637] Call Trace:
[15456.985643] [<ffffffff81046cbd>] ? warn_slowpath_common+0x78/0x8c
[15456.985647] [<ffffffff811a04d8>] ? disk_clear_events+0xb7/0xe3
[15456.985654] [<ffffffff81121afa>] ? check_disk_change+0x22/0x50
[15456.985662] [<ffffffffa005755c>] ? sd_open+0xe7/0x193 [sd_mod]
[15456.985665] [<ffffffff81122a9f>] ? __blkdev_get+0x285/0x3a9
[15456.985670] [<ffffffff81122a0c>] ? __blkdev_get+0x1f2/0x3a9
[15456.985673] [<ffffffff81122e6a>] ? blkdev_get+0x2a7/0x2a7
[15456.985676] [<ffffffff81122d8a>] ? blkdev_get+0x1c7/0x2a7
[15456.985679] [<ffffffff81036628>] ? should_resched+0x5/0x23
[15456.985682] [<ffffffff81122e6a>] ? blkdev_get+0x2a7/0x2a7
[15456.985686] [<ffffffff810f8e84>] ? __dentry_open+0x1ab/0x2c2
[15456.985689] [<ffffffff81102390>] ? dget+0x12/0x1e
[15456.985692] [<ffffffff8110542d>] ? do_last+0x553/0x58d
[15456.985695] [<ffffffff81105a5f>] ? path_openat+0xce/0x33a
[15456.985699] [<ffffffff810ce551>] ? pte_offset_kernel+0x16/0x35
[15456.985702] [<ffffffff81105d8d>] ? do_filp_open+0x2a/0x6e
[15456.985706] [<ffffffff8134deec>] ? _cond_resched+0x7/0x1c
[15456.985710] [<ffffffff811b41f9>] ? __strncpy_from_user+0x18/0x48
[15456.985713] [<ffffffff8110eb13>] ? alloc_fd+0x64/0x109
[15456.985716] [<ffffffff810f9d59>] ? do_sys_open+0x5e/0xe5
[15456.985720] [<ffffffff81354212>] ? system_call_fastpath+0x16/0x1b
[15456.985722] ---[ end trace 48ce22df61bb2ce7 ]---
[15880.360493] usb 4-1.2: USB disconnect, device number 5
[15882.603843] usb 2-1: USB disconnect, device number 2
[15888.630367] usb 2-2: new high-speed USB device number 3 using xhci_hcd
[15888.650650] usb 2-2: New USB device found, idVendor=0951, idProduct=1607
[15888.650659] usb 2-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[15888.650665] usb 2-2: Product: DataTraveler 2.0
[15888.650669] usb 2-2: Manufacturer: Kingston
[15888.650673] usb 2-2: SerialNumber: 000FEAFEFAD45B8C16070052
[15888.651862] scsi8 : usb-storage 2-2:1.0
[15889.649940] scsi 8:0:0:0: Direct-Access Kingston DataTraveler 2.0 PMAP
PQ: 0 ANSI: 0 CCS
[15889.650638] sd 8:0:0:0: Attached scsi generic sg2 type 0
[15892.052547] sd 8:0:0:0: [sdb] 15874048 512-byte logical blocks: (8.12
GB/7.56 GiB)
[15892.052764] sd 8:0:0:0: [sdb] Write Protect is off
[15892.052768] sd 8:0:0:0: [sdb] Mode Sense: 23 00 00 00
[15892.052994] sd 8:0:0:0: [sdb] No Caching mode page present
[15892.052998] sd 8:0:0:0: [sdb] Assuming drive cache: write through
[15892.054560] sd 8:0:0:0: [sdb] No Caching mode page present
[15892.054566] sd 8:0:0:0: [sdb] Assuming drive cache: write through
[15892.101439] sdb: sdb1 sdb2
[15892.102339] sd 8:0:0:0: [sdb] No Caching mode page present
[15892.102342] sd 8:0:0:0: [sdb] Assuming drive cache: write through
[15892.102344] sd 8:0:0:0: [sdb] Attached SCSI removable disk
** Model information
sys_vendor: Dell Inc.
product_name: Dell System Inspiron N411Z
product_version:
chassis_vendor: Dell Inc.
chassis_version: 0.1
bios_vendor: Dell Inc.
bios_version: A02
board_vendor: Dell Inc.
board_name:
board_version: FAB1
** Loaded modules:
nbd
cbc
ecb
ppdev
lp
vmnet(O)
parport_pc
parport
vsock(O)
vmci(O)
vmmon(O)
cpufreq_conservative
bnep
rfcomm
cpufreq_userspace
cpufreq_stats
cpufreq_powersave
8021q
binfmt_misc
garp
stp
uinput
nfsd
nfs
nfs_acl
auth_rpcgss
fscache
lockd
sunrpc
loop
fuse
ecryptfs
dm_crypt
dm_mod
snd_hda_codec_hdmi
snd_hda_codec_conexant
arc4
usbhid
hid
snd_hda_intel
snd_hda_codec
iwlwifi
snd_hwdep
snd_pcm
snd_page_alloc
mac80211
joydev
snd_seq
snd_seq_device
snd_timer
i915
drm_kms_helper
cfg80211
drm
btusb
bluetooth
i2c_i801
snd
i2c_algo_bit
dell_laptop
acpi_cpufreq
mperf
i2c_core
iTCO_wdt
iTCO_vendor_support
coretemp
rfkill
soundcore
evdev
video
dcdbas
psmouse
dell_wmi
ac
pcspkr
serio_raw
sparse_keymap
processor
button
battery
power_supply
wmi
ext4
crc16
jbd2
mbcache
ums_realtek
usb_storage
sg
sr_mod
sd_mod
cdrom
crc_t10dif
crc32c_intel
ghash_clmulni_intel
xhci_hcd
ahci
libahci
libata
ehci_hcd
aesni_intel
scsi_mod
aes_x86_64
atl1c
thermal
thermal_sys
aes_generic
cryptd
usbcore
usb_common
** PCI devices:
00:00.0 Host bridge [0600]: Intel Corporation 2nd Generation Core Processor
Family DRAM Controller [8086:0104] (rev 09)
Subsystem: Dell Device [1028:051b]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort+ >SERR- <PERR- INTx-
Latency: 0
Capabilities: <access denied>
Kernel driver in use: agpgart-intel
00:02.0 VGA compatible controller [0300]: Intel Corporation 2nd Generation Core
Processor Family Integrated Graphics Controller [8086:0116] (rev 09) (prog-if
00 [VGA controller])
Subsystem: Dell Device [1028:051b]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 46
Region 0: Memory at f0000000 (64-bit, non-prefetchable) [size=4M]
Region 2: Memory at e0000000 (64-bit, prefetchable) [size=256M]
Region 4: I/O ports at 3000 [size=64]
Expansion ROM at <unassigned> [disabled]
Capabilities: <access denied>
Kernel driver in use: i915
00:16.0 Communication controller [0780]: Intel Corporation 6 Series/C200 Series
Chipset Family MEI Controller #1 [8086:1c3a] (rev 04)
Subsystem: Dell Device [1028:051b]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 11
Region 0: Memory at f0705000 (64-bit, non-prefetchable) [size=16]
Capabilities: <access denied>
00:1a.0 USB controller [0c03]: Intel Corporation 6 Series/C200 Series Chipset
Family USB Enhanced Host Controller #2 [8086:1c2d] (rev 05) (prog-if 20 [EHCI])
Subsystem: Dell Device [1028:051b]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 16
Region 0: Memory at f070a000 (32-bit, non-prefetchable) [size=1K]
Capabilities: <access denied>
Kernel driver in use: ehci_hcd
00:1b.0 Audio device [0403]: Intel Corporation 6 Series/C200 Series Chipset
Family High Definition Audio Controller [8086:1c20] (rev 05)
Subsystem: Dell Device [1028:051b]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 48
Region 0: Memory at f0700000 (64-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: snd_hda_intel
00:1c.0 PCI bridge [0604]: Intel Corporation 6 Series/C200 Series Chipset
Family PCI Express Root Port 1 [8086:1c10] (rev b5) (prog-if 00 [Normal decode])
Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:1c.1 PCI bridge [0604]: Intel Corporation 6 Series/C200 Series Chipset
Family PCI Express Root Port 2 [8086:1c12] (rev b5) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
Memory behind bridge: f0600000-f06fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:1c.3 PCI bridge [0604]: Intel Corporation 6 Series/C200 Series Chipset
Family PCI Express Root Port 4 [8086:1c16] (rev b5) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=03, subordinate=03, sec-latency=0
Memory behind bridge: f0500000-f05fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:1c.5 PCI bridge [0604]: Intel Corporation 6 Series/C200 Series Chipset
Family PCI Express Root Port 6 [8086:1c1a] (rev b5) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=04, subordinate=04, sec-latency=0
I/O behind bridge: 00002000-00002fff
Memory behind bridge: f0400000-f04fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:1d.0 USB controller [0c03]: Intel Corporation 6 Series/C200 Series Chipset
Family USB Enhanced Host Controller #1 [8086:1c26] (rev 05) (prog-if 20 [EHCI])
Subsystem: Dell Device [1028:051b]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 23
Region 0: Memory at f0709000 (32-bit, non-prefetchable) [size=1K]
Capabilities: <access denied>
Kernel driver in use: ehci_hcd
00:1f.0 ISA bridge [0601]: Intel Corporation HM67 Express Chipset Family LPC
Controller [8086:1c4b] (rev 05)
Subsystem: Dell Device [1028:051b]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Capabilities: <access denied>
00:1f.2 SATA controller [0106]: Intel Corporation 6 Series/C200 Series Chipset
Family 6 port SATA AHCI Controller [8086:1c03] (rev 05) (prog-if 01 [AHCI 1.0])
Subsystem: Dell Device [1028:051b]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 45
Region 0: I/O ports at 3088 [size=8]
Region 1: I/O ports at 3094 [size=4]
Region 2: I/O ports at 3080 [size=8]
Region 3: I/O ports at 3090 [size=4]
Region 4: I/O ports at 3060 [size=32]
Region 5: Memory at f0708000 (32-bit, non-prefetchable) [size=2K]
Capabilities: <access denied>
Kernel driver in use: ahci
00:1f.3 SMBus [0c05]: Intel Corporation 6 Series/C200 Series Chipset Family
SMBus Controller [8086:1c22] (rev 05)
Subsystem: Dell Device [1028:051b]
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin C routed to IRQ 18
Region 0: Memory at f0704000 (64-bit, non-prefetchable) [size=256]
Region 4: I/O ports at efa0 [size=32]
02:00.0 Network controller [0280]: Intel Corporation Centrino Wireless-N 1030
[Rainbow Peak] [8086:008a] (rev 34)
Subsystem: Intel Corporation Centrino Wireless-N 1030 BGN [8086:5325]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 47
Region 0: Memory at f0600000 (64-bit, non-prefetchable) [size=8K]
Capabilities: <access denied>
Kernel driver in use: iwlwifi
03:00.0 USB controller [0c03]: NEC Corporation uPD720200 USB 3.0 Host
Controller [1033:0194] (rev 04) (prog-if 30 [XHCI])
Subsystem: Dell Device [1028:051b]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 19
Region 0: Memory at f0500000 (64-bit, non-prefetchable) [size=8K]
Capabilities: <access denied>
Kernel driver in use: xhci_hcd
04:00.0 Ethernet controller [0200]: Atheros Communications Inc. AR8152 v2.0
Fast Ethernet [1969:2062] (rev c1)
Subsystem: Dell Device [1028:051b]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 49
Region 0: Memory at f0400000 (64-bit, non-prefetchable) [size=256K]
Region 2: I/O ports at 2000 [size=128]
Capabilities: <access denied>
Kernel driver in use: atl1c
** USB devices:
Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 003 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 004 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 001 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub
Bus 004 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub
Bus 002 Device 004: ID 0951:1607 Kingston Technology DataTraveler 100
Bus 004 Device 003: ID 8086:0189 Intel Corp.
Bus 002 Device 005: ID 04f3:0234 Elan Microelectronics Corp.
Bus 004 Device 006: ID 04f2:0408 Chicony Electronics Co., Ltd
-- System Information:
Debian Release: 7.3
APT prefers stable-updates
APT policy: (500, 'stable-updates'), (500, 'stable')
Architecture: amd64 (x86_64)
Foreign Architectures: i386
Kernel: Linux 3.2.0-4-amd64 (SMP w/4 CPU cores)
Locale: LANG=es_AR.UTF-8, LC_CTYPE=es_AR.UTF-8 (charmap=UTF-8)
Shell: /bin/sh linked to /bin/dash
Versions of packages linux-image-3.2.0-4-amd64 depends on:
ii debconf [debconf-2.0] 1.5.49
ii initramfs-tools [linux-initramfs-tool] 0.109.1
ii kmod 9-3
ii linux-base 3.5
ii module-init-tools 9-3
Versions of packages linux-image-3.2.0-4-amd64 recommends:
ii firmware-linux-free 3.2
Versions of packages linux-image-3.2.0-4-amd64 suggests:
pn debian-kernel-handbook <none>
ii grub-pc 1.99-27+deb7u2
pn linux-doc-3.2 <none>
Versions of packages linux-image-3.2.0-4-amd64 is related to:
pn firmware-atheros <none>
pn firmware-bnx2 <none>
pn firmware-bnx2x <none>
pn firmware-brcm80211 <none>
pn firmware-intelwimax <none>
pn firmware-ipw2x00 <none>
pn firmware-ivtv <none>
ii firmware-iwlwifi 0.36+wheezy.1
pn firmware-libertas <none>
pn firmware-linux <none>
pn firmware-linux-nonfree <none>
pn firmware-myricom <none>
pn firmware-netxen <none>
pn firmware-qlogic <none>
ii firmware-ralink 0.36+wheezy.1
pn firmware-realtek <none>
pn xen-hypervisor <none>
-- debconf information:
linux-image-3.2.0-4-amd64/postinst/depmod-error-initrd-3.2.0-4-amd64: false
linux-image-3.2.0-4-amd64/prerm/removing-running-kernel-3.2.0-4-amd64: true
linux-image-3.2.0-4-amd64/postinst/ignoring-ramdisk:
linux-image-3.2.0-4-amd64/postinst/missing-firmware-3.2.0-4-amd64:
--
To UNSUBSCRIBE, email to debian-bugs-dist-requ...@lists.debian.org
with a subject of "unsubscribe". Trouble? Contact listmas...@lists.debian.org
