Hi, Thanks for your replies Alfred M. Szmidt and Gianluca Guida:
--- Gianluca Guida <[EMAIL PROTECTED]> wrote: > The problem you encountered may be due to the fact > that you're not > using the latest tree, that you can find at > http://wazzabbanda.homelinux.org/ . Thanks. I tried the recent tempura-stomach--20050625.tar.bz2 and it booted! I find the console response to be much faster than gnumach. Have you given lot of printfs during the boot code? The startup bootlog sequence on the T41: ----- GNUmach 1.3 AT386 boot: physical memory from 0x0 to 0x1ff60000 GNUmach 1.3 AT386 boot: physical memory from 0x0 to 0x1ff60000 pcibus_setup(1): mode 1 addr port (0x0cf8) is 0x8000f904 pcibus_setup(1a): mode1res=0x80000000 (0x80000000) pcibus_check: device 0 is there (id=33408086) Prova 0 SUBALLOCATING 21d20000 -> 21d40000 BIOS mapped to 0x21d20000 SUBALLOCATING 21d40000 -> 21d41000 SUBALLOCATING 21d41000 -> 21d42000 SUBALLOCATING 21d42000 -> 21d43000 init.c:142: pcibios_init : OSKit PCI BIOS revision 1.0 PCI: Probing PCI hardware init.c:160: init.c:164: scsi : 0 hosts. scsi : detected total. Dummy isa_bus component initialized. PCI_IDE: unknown IDE controller on PCI bus 00 device f9, VID=8086, DID=24ca PCI_IDE: not 100% native mode: will probe irqs later ide0: BM-DMA at 0x1860-0x1867, BIOS settings: hda:DMA, hdb:pio ide1: BM-DMA at 0x1868-0x186f, BIOS settings: hdc:DMA, hdd:pio hd0: C/H/S=0/0/0 from BIOS ignored hda: HTS548040M9AT00, ATA DISK drive hdc: UJDA755zDVD/CDRW, ATAPI CDROM drive ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 ide1 at 0x170-0x177,0x376 on irq 15 hda: HTS548040M9AT00, 34728MB w/7877kB Cache, CHS=4427/255/63 hdc: ATAPI 24X DVD-ROM CD-R/RW drive, 2048kB Cache Uniform CD-ROM driver Revision: 3.11 Partition check: hda: hda1 hda2 hda3 hda4 PCI bridge found: PCI0:1:0 PCI bridge found: PCI0:30:0 NCR53c406a: no available ports found vm_page_grab: no dma anymoremem_free: hash search failed (0)! vm_page_grab: no dma anymoremem_free: hash search failed (0)! vm_page_grab: no dma anymorevm_page_grab: no dma anymoreeata_dma: can't allocate enough memory to probe for hosts ! oskitcom/objs/mach_osenv_ioport.c:71: ioport_avail: bad port range [0x10c88-0x10c91] scsi: <fdomain> Detection failed (no card) SUBALLOCATING 21df2000 -> 21df3000 SUBALLOCATING 21df3000 -> 21df4000 ... ... 21e2f000 SUBALLOCATING 21e2f000 -> 2 ---- It probes for floppy and spends lot of time there. Can I disable the floppy detection? Thanks again, K Shakthi ------------------------------------------------------------ Shakthi Kannan, MS Software Engineer, Specsoft (Hexaware Technologies) [E]: [EMAIL PROTECTED] [M]: (91) 98407-87007 [W]: http://www.shakthimaan.com [L]: Chennai, India ------------------------------------------------------------ __________________________________________________ Do You Yahoo!? Tired of spam? Yahoo! Mail has the best spam protection around http://mail.yahoo.com _______________________________________________ Bug-hurd mailing list Bug-hurd@gnu.org http://lists.gnu.org/mailman/listinfo/bug-hurd
