As I said I'm a newbie Luckily I have an FTDI cable , but what software should I use as a console to read data from PB? I have Windows 10.
Actually, when I plug PB to my PC it makes the sound of connecting and a COM port appears in the Device Manager, but then another sound of disconnecting. This thing repeats for 10 times and finnaly the COM port disappears. Thnx Στις Σάββατο, 5 Δεκεμβρίου 2020 στις 7:12:18 μ.μ. UTC+2, ο χρήστης [email protected] έγραψε: > If the LEDs are not blinking as expected, that does not sound good. If > you have a FTDI cable, you could try to connect it to the PB as shown on > the following page to see if you get any messages related to the issue: > > https://beagleboard.org/p/ken-shirriff/hands-on-with-the-pocketbeagle-a-25-linux-computer-606c66 > > I'm assuming you are not seeing a COM port active for the PB on your > Windows PC, correct? > > Cheers, > > Jon > > On Sat, Dec 5, 2020 at 5:32 AM John Bacas <[email protected]> wrote: > >> I have used "*AM3358 Debian 10.3 2020-04-06 4GB SD IoT*" image file and >> I used "*rufus 3.1*" to flash the image. >> As I said, all 4 leds lighted up sequencially and after a while the user0 >> led flashed like a heartbeat and user1 led kept flashing randomly. >> That is normal as I have read, but still in my computer no device was >> detected. >> After some unplugging and plugging, I used "*Etcher*" to flash the image. >> Then I flashed some older images like "*Debian 9.9 2019-08-03 4GB SD IoT*" >> and "*AM3358 Debian 10.0 2019-07-07 4GB SD IoT*" with "Etcher" too. >> I have tried a different sd card but nothing changed. >> Yesterday when I plugged Beagle in the usb port, an "RNDIS...." message >> appeard but not any connection and only user0 led stays constantly lit. >> User0 led is about kernel, so is there any damage inside the chip? >> >> Στις Σάββατο, 5 Δεκεμβρίου 2020 στις 2:39:17 π.μ. UTC+2, ο χρήστης >> [email protected] έγραψε: >> >>> What image did you flash to the uSD card? >>> What tool did you use to flash the image to the uSD card? >>> >>> Cheers, >>> >>> Jon >>> >>> On Fri, Dec 4, 2020 at 12:36 PM John Bacas <[email protected]> wrote: >>> >>>> Hi, I'm a newbie with beagle board and I have a problem with my pocket >>>> one. >>>> I did all according to the quick start guide. >>>> When i plugged it to my pc all 4 leds lighted up sequentially but I was >>>> waiting for 1 minute and nothing happened. There wasn't any new drive >>>> appearing in my windows explorer. >>>> Unplugged it without turning it off and plugged it again. Same bahavior. >>>> After a lot o sd card flashing and tries to boot, things got worse. >>>> Now when i plug the board only user0 led lights up and stays open. >>>> Have I damaged it ? How can I check if it has damage? >>>> Can I fix it ? >>>> >>>> Thanks >>>> >>>> -- >>>> For more options, visit http://beagleboard.org/discuss >>>> --- >>>> You received this message because you are subscribed to the Google >>>> Groups "BeagleBoard" group. >>>> To unsubscribe from this group and stop receiving emails from it, send >>>> an email to [email protected]. >>>> To view this discussion on the web visit >>>> https://groups.google.com/d/msgid/beagleboard/744326f5-f51d-4c41-9771-da5272edb840n%40googlegroups.com >>>> >>>> <https://groups.google.com/d/msgid/beagleboard/744326f5-f51d-4c41-9771-da5272edb840n%40googlegroups.com?utm_medium=email&utm_source=footer> >>>> . >>>> >>> -- >> For more options, visit http://beagleboard.org/discuss >> --- >> You received this message because you are subscribed to the Google Groups >> "BeagleBoard" group. >> To unsubscribe from this group and stop receiving emails from it, send an >> email to [email protected]. >> > To view this discussion on the web visit >> https://groups.google.com/d/msgid/beagleboard/688b764d-8c22-4429-97d1-39356414818dn%40googlegroups.com >> >> <https://groups.google.com/d/msgid/beagleboard/688b764d-8c22-4429-97d1-39356414818dn%40googlegroups.com?utm_medium=email&utm_source=footer> >> . >> > -- For more options, visit http://beagleboard.org/discuss --- You received this message because you are subscribed to the Google Groups "BeagleBoard" group. To unsubscribe from this group and stop receiving emails from it, send an email to [email protected]. To view this discussion on the web visit https://groups.google.com/d/msgid/beagleboard/b42ca426-265c-4c80-b56b-4fd6fb1bdd4an%40googlegroups.com.
