On Thu, Aug 6, 2020 at 12:23 PM Michael Ascenzi <[email protected]> wrote: > > ~$ ip a > 1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN group > default qlen 1000 > link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00 > inet 127.0.0.1/8 scope host lo > valid_lft forever preferred_lft forever > inet6 ::1/128 scope host > valid_lft forever preferred_lft forever > 2: enp0s31f6: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc fq_codel > state DOWN group default qlen 1000 > link/ether 70:5a:0f:91:02:b4 brd ff:ff:ff:ff:ff:ff > 4: wlp1s0: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN group default > qlen 1000 > link/ether a4:34:d9:54:a9:25 brd ff:ff:ff:ff:ff:ff > 5: enx503f5602c060: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc fq_codel > state UP group default qlen 1000 > link/ether 50:3f:56:02:c0:60 brd ff:ff:ff:ff:ff:ff > inet 10.0.9.48/16 brd 10.0.255.255 scope global dynamic noprefixroute > enx503f5602c060 > valid_lft 604455sec preferred_lft 604455sec > inet6 fe80::534d:3bc8:b294:728f/64 scope link noprefixroute > valid_lft forever preferred_lft forever > 7: enxa0f6fd648818: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc fq_codel > state UNKNOWN group default qlen 1000 > link/ether a0:f6:fd:64:88:18 brd ff:ff:ff:ff:ff:ff > inet6 fe80::c029:c2b8:bd50:cd98/64 scope link noprefixroute > valid_lft forever preferred_lft forever > > DMESG results after plugging usb in and waiting for board to boot. > ~$ dmesg > ... > [ 487.911459] xhci_hcd 0000:00:14.0: WARN Set TR Deq Ptr cmd failed due to > incorrect slot or ep state. > [ 535.166910] usb 1-1: new high-speed USB device number 17 using xhci_hcd > [ 535.319879] usb 1-1: New USB device found, idVendor=1d6b, idProduct=0104 > [ 535.319884] usb 1-1: New USB device strings: Mfr=1, Product=2, > SerialNumber=3 > [ 535.319887] usb 1-1: Product: BeagleBoneBlack > [ 535.319890] usb 1-1: Manufacturer: BeagleBoard.org > [ 535.319893] usb 1-1: SerialNumber: 1116BBBK13C3 > [ 535.322775] rndis_host 1-1:1.0 eth0: register 'rndis_host' at > usb-0000:00:14.0-1, RNDIS device, a0:f6:fd:64:88:18 > [ 535.323716] cdc_acm 1-1:1.2: ttyACM0: USB ACM device > [ 535.360310] rndis_host 1-1:1.0 enxa0f6fd648818: renamed from eth0 > [ 535.409694] IPv6: ADDRCONF(NETDEV_UP): enxa0f6fd648818: link is not ready > mascenzi@mascenzi-l0220:~$
sudo dhclient enxa0f6fd648818 Then run ip a again to see if got an ip.. Regards, -- Robert Nelson https://rcn-ee.com/ -- For more options, visit http://beagleboard.org/discuss --- You received this message because you are subscribed to the Google Groups "BeagleBoard" group. To unsubscribe from this group and stop receiving emails from it, send an email to [email protected]. To view this discussion on the web visit https://groups.google.com/d/msgid/beagleboard/CAOCHtYh6yKE0ukw1gnratGk7frT3ok3yH2FjBXEbLJYBNuv-uQ%40mail.gmail.com.
