We have the same problem lately we thought maybe our upgrade and testing of the .13 firmware.. but we are running 20 phones on a  p4 2.6 w/512 4 PSTN lines on TDM400P and have 3 fat client pc's and 7 pcexpanions ( http://ncomputing.com/ ) running to a fat client. We did not have the issue on firmware .09 or .12. What firmware are you using?

Jeff Busch wrote:
This definitely could be the issue.  I am running 15 total devices (7
IP500 phones and 7 PC's along with a networked fax/scanner, and the
Asterisk Server) through a single 16 port switch.  

We run one MS Access app on almost all the desktops that is a
client/server app that creates a lot of traffic.  I will go to the site
tomorrow and make some changes to the topology of the LAN.

Thanks!

Jeff

-----Original Message-----
From: [EMAIL PROTECTED]
[mailto:[EMAIL PROTECTED]] On Behalf Of Steve
Blair
Sent: Tuesday, November 29, 2005 4:33 PM
To: Asterisk Users Mailing List - Non-Commercial Discussion
Subject: Re: [Asterisk-Users] Static on inside end of conversation



Jeff Busch wrote:

  
You are correct.  Inside means the IP Network and Outside means the 
PSTN accessible via the Audiocodes MP-108 gateway.

No QoS.

 

    
We've seen echo on congested LANs within our Enterprise. I'm not sure if
this fits what your seeing or not. We've placed phones in their own vlan
and added 802.1p QoS to expedite forwarding upto the first hop router
for the outbound call leg and the echo is gone. We did the same for the
inbound call leg also.

  
Thanks - Jeff

-----Original Message-----
From: [EMAIL PROTECTED]
[mailto:[EMAIL PROTECTED]] On Behalf Of Steve 
Blair
Sent: Tuesday, November 29, 2005 4:20 PM
To: Asterisk Users Mailing List - Non-Commercial Discussion
Subject: Re: [Asterisk-Users] Static on inside end of conversation



Jeff Busch wrote:

 

    
Hello,

I am running the following configuration:

2.8ghz P4 with 1GB of RAM
Audiocodes MP-108 connected to 5 POTS lines Polycom IP-500 phones 
[EMAIL PROTECTED] 1.3 (this is Asterisk 1.0.9)

End users are complaining of an echo and static on the inside end (the
      

  
internal side), but the outside end of the conversation doeesn't 
notice
   

      
 

    
anything.



   

      
I'm assuming inside means on the IP network and outside means on the 
PSTN which is accessible via a gateway is this correct? If so do you 
have QoS enabled on the inside?

 

    
Does anyone have any suggestions on troubleshooting / fixing this 
problem?

Thanks!

Jeff



_______________________________________________
--Bandwidth and Colocation provided by Easynews.com --

Asterisk-Users mailing list
To UNSUBSCRIBE or update options visit:
 http://lists.digium.com/mailman/listinfo/asterisk-users


   

      
_______________________________________________
--Bandwidth and Colocation provided by Easynews.com --

Asterisk-Users mailing list
To UNSUBSCRIBE or update options visit:
  http://lists.digium.com/mailman/listinfo/asterisk-users

_______________________________________________
--Bandwidth and Colocation provided by Easynews.com --

Asterisk-Users mailing list
To UNSUBSCRIBE or update options visit:
  http://lists.digium.com/mailman/listinfo/asterisk-users
 

    
_______________________________________________
--Bandwidth and Colocation provided by Easynews.com --

Asterisk-Users mailing list
To UNSUBSCRIBE or update options visit:
   http://lists.digium.com/mailman/listinfo/asterisk-users

_______________________________________________
--Bandwidth and Colocation provided by Easynews.com --

Asterisk-Users mailing list
To UNSUBSCRIBE or update options visit:
   http://lists.digium.com/mailman/listinfo/asterisk-users
  
_______________________________________________
--Bandwidth and Colocation provided by Easynews.com --

Asterisk-Users mailing list
To UNSUBSCRIBE or update options visit:
   http://lists.digium.com/mailman/listinfo/asterisk-users

Reply via email to