smartctl -C /dev/sdb1 smartctl 5.41 2011-06-09 r3365 [i686-linux-3.2.0-34-generic] (local build) Copyright (C) 2002-11 by Bruce Allen, http://smartmontools.sourceforge.net
=== START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: FAILED! Drive failure expected in less than 24 hours. SAVE ALL DATA. Failed Attributes: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 5 Reallocated_Sector_Ct 0x0033 001 001 036 Pre-fail Always FAILING_NOW 2042 smartctl -a /dev/sdb1 smartctl 5.41 2011-06-09 r3365 [i686-linux-3.2.0-34-generic] (local build) Copyright (C) 2002-11 by Bruce Allen, http://smartmontools.sourceforge.net === START OF INFORMATION SECTION === Model Family: Seagate Barracuda ES.2 Device Model: ST3500320NS Serial Number: 9QMCB7P6 LU WWN Device Id: 5 000c50 019e90f65 Firmware Version: SN06 User Capacity: 500,107,862,016 bytes [500 GB] Sector Size: 512 bytes logical/physical Device is: In smartctl database [for details use: -P show] ATA Version is: 8 ATA Standard is: ATA-8-ACS revision 4 Local Time is: Wed Dec 12 10:57:03 2012 EST SMART support is: Available - device has SMART capability. SMART support is: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: FAILED! Drive failure expected in less than 24 hours. SAVE ALL DATA. See vendor-specific Attribute list for failed Attributes. General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 625) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 110) minutes. Conveyance self-test routine recommended polling time: ( 2) minutes. SCT capabilities: (0x103d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x000f 069 045 044 Pre-fail Always - 8074151 3 Spin_Up_Time 0x0003 099 099 000 Pre-fail Always - 0 4 Start_Stop_Count 0x0032 100 100 020 Old_age Always - 62 5 Reallocated_Sector_Ct 0x0033 001 001 036 Pre-fail Always FAILING_NOW 2042 7 Seek_Error_Rate 0x000f 081 060 030 Pre-fail Always - 4419180241 9 Power_On_Hours 0x0032 075 075 000 Old_age Always - 22497 10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0 12 Power_Cycle_Count 0x0032 100 037 020 Old_age Always - 62 184 End-to-End_Error 0x0032 100 100 099 Old_age Always - 0 187 Reported_Uncorrect 0x0032 001 001 000 Old_age Always - 1981 188 Command_Timeout 0x0032 100 099 000 Old_age Always - 12885098499 189 High_Fly_Writes 0x003a 097 097 000 Old_age Always - 3 190 Airflow_Temperature_Cel 0x0022 064 059 045 Old_age Always - 36 (Min/Max 36/41) 194 Temperature_Celsius 0x0022 036 041 000 Old_age Always - 36 (0 15 0 0) 195 Hardware_ECC_Recovered 0x001a 042 035 000 Old_age Always - 8074151 197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 0 198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline - 0 199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0 SMART Error Log Version: 1 ATA Error Count: 1246 (device log contains only the most recent five errors) CR = Command Register [HEX] FR = Features Register [HEX] SC = Sector Count Register [HEX] SN = Sector Number Register [HEX] CL = Cylinder Low Register [HEX] CH = Cylinder High Register [HEX] DH = Device/Head Register [HEX] DC = Device Command Register [HEX] ER = Error register [HEX] ST = Status register [HEX] Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 1246 occurred at disk power-on lifetime: 22142 hours (922 days + 14 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 25 00 00 ff ff ff ef 00 8d+05:15:09.200 READ DMA EXT 27 00 00 00 00 00 e0 00 8d+05:15:09.171 READ NATIVE MAX ADDRESS EXT ec 00 00 00 00 00 a0 00 8d+05:15:09.091 IDENTIFY DEVICE ef 03 46 00 00 00 a0 00 8d+05:15:09.071 SET FEATURES [Set transfer mode] 27 00 00 00 00 00 e0 00 8d+05:15:09.043 READ NATIVE MAX ADDRESS EXT Error 1245 occurred at disk power-on lifetime: 22142 hours (922 days + 14 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 25 00 00 ff ff ff ef 00 8d+05:15:06.024 READ DMA EXT 27 00 00 00 00 00 e0 00 8d+05:15:05.995 READ NATIVE MAX ADDRESS EXT ec 00 00 00 00 00 a0 00 8d+05:15:05.987 IDENTIFY DEVICE ef 03 46 00 00 00 a0 00 8d+05:15:05.943 SET FEATURES [Set transfer mode] 27 00 00 00 00 00 e0 00 8d+05:15:05.915 READ NATIVE MAX ADDRESS EXT Error 1244 occurred at disk power-on lifetime: 22142 hours (922 days + 14 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 25 00 00 ff ff ff ef 00 8d+05:15:02.836 READ DMA EXT 27 00 00 00 00 00 e0 00 8d+05:15:02.807 READ NATIVE MAX ADDRESS EXT ec 00 00 00 00 00 a0 00 8d+05:15:02.799 IDENTIFY DEVICE ef 03 46 00 00 00 a0 00 8d+05:15:02.755 SET FEATURES [Set transfer mode] 27 00 00 00 00 00 e0 00 8d+05:15:02.727 READ NATIVE MAX ADDRESS EXT Error 1243 occurred at disk power-on lifetime: 22142 hours (922 days + 14 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 25 00 00 ff ff ff ef 00 8d+05:14:59.672 READ DMA EXT 27 00 00 00 00 00 e0 00 8d+05:14:59.643 READ NATIVE MAX ADDRESS EXT ec 00 00 00 00 00 a0 00 8d+05:14:59.636 IDENTIFY DEVICE ef 03 46 00 00 00 a0 00 8d+05:14:59.590 SET FEATURES [Set transfer mode] 27 00 00 00 00 00 e0 00 8d+05:14:59.563 READ NATIVE MAX ADDRESS EXT Error 1242 occurred at disk power-on lifetime: 22142 hours (922 days + 14 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 25 00 00 ff ff ff ef 00 8d+05:14:56.149 READ DMA EXT 25 00 00 ff ff ff ef 00 8d+05:14:55.549 READ DMA EXT 25 00 00 ff ff ff ef 00 8d+05:14:54.770 READ DMA EXT 25 00 00 ff ff ff ef 00 8d+05:14:53.141 READ DMA EXT 25 00 00 ff ff ff ef 00 8d+05:14:51.106 READ DMA EXT SMART Self-test log structure revision number 1 Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed: unknown failure 90% 21203 0 # 2 Short offline Completed: unknown failure 90% 21203 0 # 3 Conveyance offline Completed: unknown failure 90% 21203 0 SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. On Wed, Dec 12, 2012 at 10:39 AM, Steven Stern < subscribed-li...@sterndata.com> wrote: > On 12/11/2012 04:22 PM, L wrote: > > Hi > > The disk utility shows one of my disks are failling. I check it using > > > > sudo e2fsck -f -c -v /dev/sdb1 > > e2fsck 1.42 (29-Nov-2011) > > Checking for bad blocks (read-only test): 0.00% done, 0:00 elapsed. > > (0/0/0 errdone > > 500G: Updating bad block inode. > > Pass 1: Checking inodes, blocks, and sizes > > Pass 2: Checking directory structure > > Pass 3: Checking directory connectivity > > Pass 4: Checking reference counts > > Pass 5: Checking group summary information > > > > 500G: ***** FILE SYSTEM WAS MODIFIED ***** > > > > 124186 inodes used (0.41%) > > 2600 non-contiguous files (2.1%) > > 195 non-contiguous directories (0.2%) > > # of inodes with ind/dind/tind blocks: 0/0/0 > > Extent depth histogram: 120688/867 > > 52973023 blocks used (43.39%) > > 0 bad blocks > > 1 large file > > > > 118955 regular files > > 2148 directories > > 0 character device files > > 0 block device files > > 0 fifos > > 0 links > > 3074 symbolic links (2623 fast symbolic links) > > 0 sockets > > -------- > > 124177 files > > > > I am confused if this disk is really failing?? > > > > Yuan > > > > > > > What does smartctl /dev/sdb -H and smartctl /dev/sdb -a show? > > -- > -- Steve > -- > users mailing list > users@lists.fedoraproject.org > To unsubscribe or change subscription options: > https://admin.fedoraproject.org/mailman/listinfo/users > Guidelines: http://fedoraproject.org/wiki/Mailing_list_guidelines > Have a question? Ask away: http://ask.fedoraproject.org > -- °v° /( $ )\ Linux Toys ^ ^ http://linuxishbell.wordpress.com/
-- users mailing list users@lists.fedoraproject.org To unsubscribe or change subscription options: https://admin.fedoraproject.org/mailman/listinfo/users Guidelines: http://fedoraproject.org/wiki/Mailing_list_guidelines Have a question? Ask away: http://ask.fedoraproject.org
