Public bug reported:
Binary package hint: hal-device-manager
I have a highpoint rocketraid 1540 card to which I have a 200gb seagate drive
attached. Under the feisty livecd this drive is mounted like all the rest in my
pc and I can access it normally. Under feisty and now under gutsy, I have to
disconnect the drive or put it on port 3 or 4 for the pc to get past the ubuntu
splash screen or else, the machine hangs at that point. Upon further
investigation, by booting up from the fiesty cd again I have found that in the
hardware manager there, there is only one instance of the module hpt374 with no
reference to hpt366. In my gutsy installation however, there are two
instances of hpt374 in the hardware manager list, one of which resembles the
same entry from the list when the feisty Livecd is loaded and another which
makes reference to the linux driver hpt366. I have blacklisted this module and
it is no longer loading, however I am still getting two hpt374 modules
loading(as opposed to the single one in feisty) and one the modules has this
reference to the hpt366 module which is not the one for my interface card.
Since this drive holds a lot of my data I have only two options at present
(that I know of) if I wish to access that drive. One, on a temporary basis, is
to boot up from the feisty cd again and again anytime I wish to access it, as
it works perfectly from the live cd. The other is to change my motherboard to
one that has more "native" sata ports as this current one has only two and this
I am loathe to do at this present time.
Since the drive works on the feisty Livecd and only loads one HPT374 module,
with no reference anywhere to the malfunctioning HPT366 module; I can only
assume that there must be some bug in the system that is loading the hpt374
module twice! and linking it to the hpt366 driver in one instance.
below is the output from when I type dmesg in the terminal.......
48.698824] NFORCE2: IDE controller at PCI slot 0000:00:09.0
[ 48.698849] NFORCE2: chipset revision 162
[ 48.698851] NFORCE2: not 100% native mode: will probe irqs later
[ 48.698855] NFORCE2: BIOS didn't set cable bits correctly. Enabling
workaround.
[ 48.698857] NFORCE2: BIOS didn't set cable bits correctly. Enabling
workaround.
[ 48.698863] NFORCE2: 0000:00:09.0 (rev a2) UDMA133 controller
[ 48.698873] ide0: BM-DMA at 0xf000-0xf007, BIOS settings: hda:DMA,
hdb:DMA
[ 48.698885] ide1: BM-DMA at 0xf008-0xf00f, BIOS settings: hdc:DMA,
hdd:DMA
[ 48.698893] Probing IDE interface ide0...
[ 48.986396] hda: MAXTOR STM3160215A, ATA DISK drive
[ 49.210085] usb 2-2: new low speed USB device using ohci_hcd and address 2
[ 49.266156] hdb: IBM-DTLA-307030, ATA DISK drive
[ 49.322735] ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
[ 49.325552] Probing IDE interface ide1...
[ 49.428852] usb 2-2: configuration #1 chosen from 1 choice
[ 49.443924] usbcore: registered new interface driver hiddev
[ 49.450083] input: Dell Dell USB Mouse as /class/input/input2
[ 49.450209] input: USB HID v1.10 Mouse [Dell Dell USB Mouse] on
usb-0000:00:02.1-2
[ 49.450223] usbcore: registered new interface driver usbhid
[ 49.450227]
/build/buildd/linux-source-2.6.22-2.6.22/drivers/hid/usbhid/hid-core.c:
v2.6:USB HID core driver
[ 50.061481] hdc: ASUS DRW-1608P3S, ATAPI CD/DVD-ROM drive
[ 50.733032] ide1 at 0x170-0x177,0x376 on irq 15
[ 50.737788] HPT374: IDE controller at PCI slot 0000:01:09.0
[ 50.737994] ACPI: PCI Interrupt Link [APC2] enabled at IRQ 17
[ 50.738002] ACPI: PCI Interrupt 0000:01:09.0[A] -> Link [APC2] -> GSI 17
(level, high) -> IRQ 19
[ 50.738014] HPT374: chipset revision 7
[ 50.738029] HPT374: DPLL base: 48 MHz, f_CNT: 127, assuming 33 MHz PCI
[ 50.742964] HPT374: using 50 MHz DPLL clock
[ 50.743071] HPT374: 100% native mode on irq 19
[ 50.743083] ide2: BM-DMA at 0xa000-0xa007, BIOS settings: hde:pio,
hdf:pio
[ 50.743106] ide3: BM-DMA at 0xa008-0xa00f, BIOS settings: hdg:pio,
hdh:pio
[ 50.743153] ACPI: PCI Interrupt 0000:01:09.1[A] -> Link [APC2] -> GSI 17
(level, high) -> IRQ 19
[ 50.743171] HPT374: no clock data saved by BIOS
[ 50.870303] HPT374: DPLL base: 48 MHz, f_CNT: 122, assuming 33 MHz PCI
[ 50.875222] HPT374: using 50 MHz DPLL clock
[ 50.875329] HPT374: too many IDE interfaces, no room in table
[ 50.875333] HPT374: too many IDE interfaces, no room in table
[ 50.875335] HPT374: neither IDE port enabled (BIOS)
[ 50.875340] Probing IDE interface ide2...
[ 50.890030] hda: max request size: 512KiB
[ 50.934236] hda: 312581808 sectors (160041 MB) w/2048KiB Cache,
CHS=19457/255/63, UDMA(100)
[ 50.958593] hda: cache flushes supported
[ 50.958645] hda: hda1 hda2 < hda5 >
[ 50.995248] hdb: max request size: 128KiB
[ 51.023211] hdb: 60036480 sectors (30738 MB) w/1916KiB Cache,
CHS=59560/16/63, UDMA(100)
[ 51.023216] hdb: cache flushes not supported
[ 51.023237] hdb: hdb1 < hdb5 hdb6 hdb7 hdb8 hdb9 hdb10 >
[ 51.110502] hdc: ATAPI 40X DVD-ROM DVD-R-RAM CD-R/RW drive, 2000kB Cache,
UDMA(66)
[ 51.110512] Uniform CD-ROM driver Revision: 3.20
[ 51.440193] Probing IDE interface ide3...
[ 52.008120] ACPI: PCI Interrupt Link [AP3C] enabled at IRQ 22
[ 52.008127] ACPI: PCI Interrupt 0000:02:01.0[A] -> Link [AP3C] -> GSI 22
(level, high) -> IRQ 16
[ 52.008134] 3c59x: Donald Becker and others.
[ 52.008140] 0000:02:01.0: 3Com PCI 3c920 Tornado at f883a000.
[ 52.031428] ACPI: PCI Interrupt Link [APCM] enabled at IRQ 21
[ 52.031434] ACPI: PCI Interrupt 0000:00:0d.0[A] -> Link [APCM] -> GSI 21
(level, high) -> IRQ 17
[ 52.031441] PCI: Setting latency timer of device 0000:00:0d.0 to 64
[ 52.083524] ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[17]
MMIO=[e6082000-e60827ff] Max Packet=[2048] IR/IT contexts=[4/4]
[ 52.090025] sata_sil 0000:01:0b.0: version 2.2
[ 52.090266] ACPI: PCI Interrupt Link [APC3] enabled at IRQ 18
[ 52.090275] ACPI: PCI Interrupt 0000:01:0b.0[A] -> Link [APC3] -> GSI 18
(level, high) -> IRQ 20
[ 52.090731] scsi0 : sata_sil
[ 52.090939] scsi1 : sata_sil
[ 52.091077] ata1: SATA max UDMA/100 cmd 0xf884c080 ctl 0xf884c08a bmdma
0xf884c000 irq 20
[ 52.091082] ata2: SATA max UDMA/100 cmd 0xf884c0c0 ctl 0xf884c0ca bmdma
0xf884c008 irq 20
[ 52.611208] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 52.619757] ata1.00: ATA-6: ST3120023AS, 3.01, max UDMA/133
[ 52.619760] ata1.00: 234441648 sectors, multi 16: LBA
[ 52.619762] ata1.00: applying bridge limits
[ 52.619768] ata1.00: applying Seagate errata fix (mod15write workaround)
[ 52.635733] ata1.00: configured for UDMA/100
[ 53.102788] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 53.112526] ata2.00: ATA-6: WDC WD2000JD-00GBB0, 02.05D02, max UDMA/100
[ 53.112529] ata2.00: 390721968 sectors, multi 16: LBA48
[ 53.112531] ata2.00: applying bridge limits
[ 53.128533] ata2.00: configured for UDMA/100
[ 53.128649] scsi 0:0:0:0: Direct-Access ATA ST3120023AS 3.01
PQ: 0 ANSI: 5
[ 53.129003] scsi 1:0:0:0: Direct-Access ATA WDC WD2000JD-00G 02.0
PQ: 0 ANSI: 5
[ 53.139444] sd 0:0:0:0: [sda] 234441648 512-byte hardware sectors (120034 MB)
[ 53.139460] sd 0:0:0:0: [sda] Write Protect is off
[ 53.139463] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 53.139478] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled,
doesn't support DPO or FUA
[ 53.139539] sd 0:0:0:0: [sda] 234441648 512-byte hardware sectors (120034 MB)
[ 53.139548] sd 0:0:0:0: [sda] Write Protect is off
[ 53.139551] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 53.139564] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled,
doesn't support DPO or FUA
[ 53.139570] sda: sda1 sda2 < sda5 sda6 sda7 sda8 sda9 >
[ 53.220523] sd 0:0:0:0: [sda] Attached SCSI disk
[ 53.220676] sd 1:0:0:0: [sdb] 390721968 512-byte hardware sectors (200050 MB)
[ 53.220686] sd 1:0:0:0: [sdb] Write Protect is off
[ 53.220689] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 53.220703] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled,
doesn't support DPO or FUA
[ 53.220743] sd 1:0:0:0: [sdb] 390721968 512-byte hardware sectors (200050 MB)
[ 53.220752] sd 1:0:0:0: [sdb] Write Protect is off
[ 53.220754] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 53.220769] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled,
doesn't support DPO or FUA
[ 53.220771] sdb: sdb1 < sdb5 sdb6 >
[ 53.264134] sd 1:0:0:0: [sdb] Attached SCSI disk
[ 53.268378] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 53.268399] sd 1:0:0:0: Attached scsi generic sg1 type 0
[ 53.735118] device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised:
[EMAIL PROTECTED]
[ 54.135075] Attempting manual resume
[ 54.135079] swsusp: Resume From Partition 3:5
[ 54.135081] PM: Checking swsusp image.
[ 54.162428] PM: Resume from disk failed.
[ 54.202654] kjournald starting. Commit interval 5 seconds
[ 54.202665] EXT3-fs: mounted filesystem with ordered data mode.
[ 60.721593] Linux agpgart interface v0.102 (c) Dave Jones
[ 60.722893] agpgart: Detected NVIDIA nForce2 chipset
[ 60.738652] agpgart: AGP aperture is 256M @ 0xc0000000
[ 61.463578] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 61.474099] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 61.502998] i2c-adapter i2c-0: nForce2 SMBus adapter at 0x5000
[ 61.503035] i2c-adapter i2c-1: nForce2 SMBus adapter at 0x5500
[ 62.065391] input: PC Speaker as /class/input/input3
[ 62.384989] parport_pc 00:09: reported by Plug and Play ACPI
[ 62.385050] parport0: PC-style at 0x378 (0x778), irq 7, dma 3
[PCSPP,TRISTATE,COMPAT,ECP,DMA]
[ 62.617915] nvidia: module license 'NVIDIA' taints kernel.
[ 62.880182] ACPI: PCI Interrupt Link [APC4] enabled at IRQ 19
[ 62.880191] ACPI: PCI Interrupt 0000:03:00.0[A] -> Link [APC4] -> GSI 19
(level, high) -> IRQ 21
[ 62.880599] NVRM: loading NVIDIA UNIX x86 Kernel Module 100.14.19 Wed Sep
12 14:12:24 PDT 2007
[ 63.126312] ACPI: PCI Interrupt Link [APCJ] enabled at IRQ 20
[ 63.126318] ACPI: PCI Interrupt 0000:00:06.0[A] -> Link [APCJ] -> GSI 20
(level, high) -> IRQ 18
[ 63.126342] PCI: Setting latency timer of device 0000:00:06.0 to 64
[ 63.449943] intel8x0_measure_ac97_clock: measured 52839 usecs
[ 63.449947] intel8x0: clocking to 47407
[ 63.987830] lp0: using parport0 (interrupt-driven).
[ 64.032214] Adding 3943916k swap on /dev/hda5. Priority:-1 extents:1
across:3943916k
[ 64.744389] EXT3 FS on hda1, internal journal
ProblemType: Bug
Architecture: i386
Date: Thu Nov 1 22:57:45 2007
DistroRelease: Ubuntu 7.10
NonfreeKernelModules: nvidia
Package: hal 0.5.9.1-6ubuntu5
PackageArchitecture: i386
SourcePackage: hal
Uname: Linux n3m3sis1-desktop 2.6.22-14-generic #1 SMP Sun Oct 14 23:05:12 GMT
2007 i686 GNU/Linux
** Affects: hal (Ubuntu)
Importance: Undecided
Status: New
** Tags: apport-bug
--
HPT366 still linked to HPT374 after blacklist
https://bugs.launchpad.net/bugs/159397
You received this bug notification because you are a member of Ubuntu
Bugs, which is the bug contact for Ubuntu.
--
ubuntu-bugs mailing list
ubuntu-bugs@lists.ubuntu.com
https://lists.ubuntu.com/mailman/listinfo/ubuntu-bugs
