** Description changed: Binary package hint: linux-source-2.6.15 i'm not able to use my sd-flash reader in ubuntu; other operating systems handle it well hasn't worked in dapper.. i can't recall if i tried breezy i put an sd card in, the card reader light will light up for a bit and then turn off; i suppose this is an obscure device.. laptop is an acer ferrari 3400 thanks for your time Linux ferrari 2.6.15-26-686 #1 SMP PREEMPT Fri Sep 8 20:16:40 UTC 2006 i686 GNU/Linux - - [EMAIL PROTECTED]:~# lsusb - Bus 004 Device 002: ID 04b4:6560 Cypress Semiconductor Corp. CY7C65640 USB-2.0 "TetraHub" - Bus 004 Device 001: ID 0000:0000 - Bus 001 Device 001: ID 0000:0000 - Bus 003 Device 002: ID 0483:0321 SGS Thomson Microelectronics - Bus 003 Device 001: ID 0000:0000 - Bus 002 Device 001: ID 0000:0000 - - dmesg: - [17179569.184000] Linux version 2.6.15-26-686 ([EMAIL PROTECTED]) (gcc version 4.0.3 (Ubuntu 4.0.3-1ubuntu5)) #1 SMP PREEMPT Fri Sep 8 20:16:40 UTC 2006 - [17179569.184000] BIOS-provided physical RAM map: - [17179569.184000] BIOS-e820: 0000000000000000 - 000000000009b800 (usable) - [17179569.184000] BIOS-e820: 000000000009b800 - 00000000000a0000 (reserved) - [17179569.184000] BIOS-e820: 00000000000dc000 - 0000000000100000 (reserved) - [17179569.184000] BIOS-e820: 0000000000100000 - 000000001fef0000 (usable) - [17179569.184000] BIOS-e820: 000000001fef0000 - 000000001fefa000 (ACPI data) - [17179569.184000] BIOS-e820: 000000001fefa000 - 000000001ff00000 (ACPI NVS) - [17179569.184000] BIOS-e820: 000000001ff00000 - 0000000020000000 (reserved) - [17179569.184000] BIOS-e820: 00000000fffe0000 - 0000000100000000 (reserved) - [17179569.184000] 0MB HIGHMEM available. - [17179569.184000] 510MB LOWMEM available. - [17179569.184000] found SMP MP-table at 000f68f0 - [17179569.184000] On node 0 totalpages: 130800 - [17179569.184000] DMA zone: 4096 pages, LIFO batch:0 - [17179569.184000] DMA32 zone: 0 pages, LIFO batch:0 - [17179569.184000] Normal zone: 126704 pages, LIFO batch:31 - [17179569.184000] HighMem zone: 0 pages, LIFO batch:0 - [17179569.184000] DMI 2.3 present. - [17179569.184000] ACPI: RSDP (v000 PTLTD ) @ 0x000f6950 - [17179569.184000] ACPI: RSDT (v001 PTLTD RSDT 0x06040000 LTP 0x00000000) @ 0x1fef43e3 - [17179569.184000] ACPI: FADT (v001 AMDK8 PTLTW 0x06040000 PTL_ 0x000f4240) @ 0x1fef9e1d - [17179569.184000] ACPI: SSDT (v001 PTLTD POWERNOW 0x06040000 LTP 0x00000001) @ 0x1fef9e91 - [17179569.184000] ACPI: MADT (v001 PTLTD APIC 0x06040000 LTP 0x00000000) @ 0x1fef9f88 - [17179569.184000] ACPI: BOOT (v001 PTLTD $SBFTBL$ 0x06040000 LTP 0x00000001) @ 0x1fef9fd8 - [17179569.184000] ACPI: DSDT (v001 VIA PTL_ACPI 0x06040000 MSFT 0x0100000e) @ 0x00000000 - [17179569.184000] ACPI: PM-Timer IO Port: 0x4008 - [17179569.184000] ACPI: Local APIC address 0xfee00000 - [17179569.184000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled) - [17179569.184000] Processor #0 15:12 APIC version 16 - [17179569.184000] ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1]) - [17179569.184000] ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0]) - [17179569.184000] IOAPIC[0]: apic_id 1, version 3, address 0xfec00000, GSI 0-23 - [17179569.184000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 high edge) - [17179569.184000] ACPI: IRQ0 used by override. - [17179569.184000] ACPI: IRQ2 used by override. - [17179569.184000] ACPI: IRQ10 used by override. - [17179569.184000] Enabling APIC mode: Flat. Using 1 I/O APICs - [17179569.184000] Using ACPI (MADT) for SMP configuration information - [17179569.184000] Allocating PCI resources starting at 30000000 (gap: 20000000:dffe0000) - [17179569.184000] Built 1 zonelists - [17179569.184000] Kernel command line: root=/dev/hda1 ro quiet splash - [17179569.184000] mapped APIC to ffffd000 (fee00000) - [17179569.184000] mapped IOAPIC to ffffc000 (fec00000) - [17179569.184000] Initializing CPU#0 - [17179569.184000] PID hash table entries: 2048 (order: 11, 32768 bytes) - [17179569.184000] Detected 2004.831 MHz processor. - [17179569.184000] Using pmtmr for high-res timesource - [17179569.184000] Console: colour VGA+ 80x25 - [17179569.524000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) - [17179569.524000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) - [17179569.532000] Memory: 506968k/523200k available (2115k kernel code, 15576k reserved, 595k data, 332k init, 0k highmem) - [17179569.532000] Checking if this processor honours the WP bit even in supervisor mode... Ok. - [17179569.612000] Calibrating delay using timer specific routine.. 4014.07 BogoMIPS (lpj=8028149) - [17179569.612000] Security Framework v1.0.0 initialized - [17179569.612000] SELinux: Disabled at boot. - [17179569.612000] Mount-cache hash table entries: 512 - [17179569.612000] CPU: After generic identify, caps: 078bfbff e3d3fbff 00000000 00000000 00000000 00000000 00000000 - [17179569.612000] CPU: After vendor identify, caps: 078bfbff e3d3fbff 00000000 00000000 00000000 00000000 00000000 - [17179569.612000] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) - [17179569.612000] CPU: L2 Cache: 512K (64 bytes/line) - [17179569.612000] CPU: After all inits, caps: 078bfbff e3d3fbff 00000000 00000410 00000000 00000000 00000000 - [17179569.612000] mtrr: v2.0 (20020519) - [17179569.612000] Enabling fast FPU save and restore... done. - [17179569.612000] Enabling unmasked SIMD FPU exception support... done. - [17179569.612000] Checking 'hlt' instruction... OK. - [17179569.628000] SMP alternatives: switching to UP code - [17179569.628000] checking if image is initramfs... it is - [17179570.136000] Freeing initrd memory: 6809k freed - [17179570.144000] ACPI: Looking for DSDT ... not found! - [17179570.148000] CPU0: AMD Mobile AMD Athlon 64 Processor 3000+ stepping 00 - [17179570.148000] Total of 1 processors activated (4014.07 BogoMIPS). - [17179570.148000] ENABLING IO-APIC IRQs - [17179570.148000] ..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1 - [17179570.292000] Brought up 1 CPUs - [17179570.292000] NET: Registered protocol family 16 - [17179570.292000] EISA bus registered - [17179570.292000] ACPI: bus type pci registered - [17179570.292000] PCI: PCI BIOS revision 2.10 entry at 0xfd64c, last bus=1 - [17179570.292000] PCI: Using configuration type 1 - [17179570.292000] ACPI: Subsystem revision 20051216 - [17179570.292000] ACPI: Interpreter enabled - [17179570.292000] ACPI: Using IOAPIC for interrupt routing - [17179570.292000] ACPI: PCI Root Bridge [PCI0] (0000:00) - [17179570.292000] PCI: Probing PCI hardware (bus 00) - [17179570.296000] PCI quirk: region 4000-407f claimed by vt8235 PM - [17179570.296000] PCI quirk: region 8100-810f claimed by vt8235 SMB - [17179570.296000] Boot video device is 0000:01:00.0 - [17179570.296000] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] - [17179570.300000] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGP_._PRT] - [17179570.300000] ACPI: PCI Interrupt Link [ALKA] (IRQs 16 17 18 19 20 21 22 23) *5, disabled. - [17179570.300000] ACPI: PCI Interrupt Link [ALKB] (IRQs 16 17 18 19 20 21 22 23) *9, disabled. - [17179570.300000] ACPI: PCI Interrupt Link [ALKC] (IRQs 22) *11, disabled. - [17179570.300000] ACPI: PCI Interrupt Link [ALKD] (IRQs 21) *5, disabled. - [17179570.300000] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 *5 7 9 12 14 15) - [17179570.300000] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 7 10 12 14 15) *9 - [17179570.300000] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 7 *11 12 14 15) - [17179570.300000] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 *5 7 9 10 11 12 14 15) - [17179570.300000] ACPI: Embedded Controller [EC0] (gpe 1) interrupt mode. - [17179570.312000] Linux Plug and Play Support v0.97 (c) Adam Belay - [17179570.312000] pnp: PnP ACPI init - [17179570.312000] pnp: PnP ACPI: found 9 devices - [17179570.312000] PnPBIOS: Disabled by ACPI PNP - [17179570.312000] PCI: Using ACPI for IRQ routing - [17179570.312000] PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report - [17179570.316000] pnp: 00:05: ioport range 0x600-0x60f has been reserved - [17179570.316000] pnp: 00:05: ioport range 0x4d0-0x4d1 has been reserved - [17179570.316000] pnp: 00:05: ioport range 0xfe10-0xfe11 could not be reserved - [17179570.316000] pnp: 00:05: ioport range 0xfe00-0xfe00 has been reserved - [17179570.316000] PCI: Bridge: 0000:00:01.0 - [17179570.316000] IO window: 2000-2fff - [17179570.316000] MEM window: d0100000-d01fffff - [17179570.316000] PREFETCH window: d8000000-dfffffff - [17179570.316000] PCI: Bus 2, cardbus bridge: 0000:00:07.0 - [17179570.316000] IO window: 00001c00-00001cff - [17179570.316000] IO window: 00003000-000030ff - [17179570.316000] PREFETCH window: 30000000-31ffffff - [17179570.316000] MEM window: 32000000-33ffffff - [17179570.316000] PCI: Setting latency timer of device 0000:00:01.0 to 64 - [17179570.316000] ACPI: PCI Interrupt 0000:00:07.0[A] -> GSI 17 (level, low) -> IRQ 169 - [17179570.316000] PCI: Setting latency timer of device 0000:00:07.0 to 64 - [17179570.316000] Simple Boot Flag at 0x37 set to 0x1 - [17179570.316000] audit: initializing netlink socket (disabled) - [17179570.316000] audit(1158491693.312:1): initialized - [17179570.316000] VFS: Disk quotas dquot_6.5.1 - [17179570.316000] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) - [17179570.316000] Initializing Cryptographic API - [17179570.316000] io scheduler noop registered - [17179570.316000] io scheduler anticipatory registered - [17179570.316000] io scheduler deadline registered - [17179570.316000] io scheduler cfq registered - [17179570.316000] isapnp: Scanning for PnP cards... - [17179570.672000] isapnp: No Plug & Play device found - [17179570.684000] Real Time Clock Driver v1.12 - [17179570.684000] PNP: PS/2 Controller [PNP0303:KBC,PNP0f13:PS2M] at 0x60,0x64 irq 1,12 - [17179570.684000] serio: i8042 AUX port at 0x60,0x64 irq 12 - [17179570.684000] serio: i8042 KBD port at 0x60,0x64 irq 1 - [17179570.684000] Serial: 8250/16550 driver $Revision: 1.90 $ 48 ports, IRQ sharing enabled - [17179570.688000] RAMDISK driver initialized: 16 RAM disks of 65536K size 1024 blocksize - [17179570.688000] Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 - [17179570.688000] ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx - [17179570.688000] mice: PS/2 mouse device common for all mice - [17179570.688000] EISA: Probing bus 0 at eisa.0 - [17179570.688000] Cannot allocate resource for EISA slot 1 - [17179570.688000] Cannot allocate resource for EISA slot 2 - [17179570.688000] Cannot allocate resource for EISA slot 3 - [17179570.688000] Cannot allocate resource for EISA slot 4 - [17179570.688000] EISA: Detected 0 cards. - [17179570.688000] NET: Registered protocol family 2 - [17179570.724000] IP route cache hash table entries: 4096 (order: 2, 16384 bytes) - [17179570.724000] TCP established hash table entries: 16384 (order: 5, 196608 bytes) - [17179570.724000] TCP bind hash table entries: 16384 (order: 5, 196608 bytes) - [17179570.724000] TCP: Hash tables configured (established 16384 bind 16384) - [17179570.724000] TCP reno registered - [17179570.724000] TCP bic registered - [17179570.724000] NET: Registered protocol family 1 - [17179570.724000] NET: Registered protocol family 8 - [17179570.724000] NET: Registered protocol family 20 - [17179570.724000] Using IPI No-Shortcut mode - [17179570.724000] ACPI wakeup devices: - [17179570.724000] PCI0 USB1 USB2 USB3 GIGA Z000 - [17179570.724000] ACPI: (supports S0 S3 S4 S5) - [17179570.724000] Freeing unused kernel memory: 332k freed - [17179570.728000] input: AT Translated Set 2 keyboard as /class/input/input0 - [17179570.760000] vga16fb: initializing - [17179570.760000] vga16fb: mapped to 0xc00a0000 - [17179570.864000] Console: switching to colour frame buffer device 80x25 - [17179570.864000] fb0: VGA16 VGA frame buffer device - [17179571.932000] Capability LSM initialized - [17179572.060000] ACPI: CPU0 (power states: C1[C1] C2[C2]) - [17179572.064000] ACPI: Thermal Zone [THRM] (47 C) - [17179572.480000] VP_IDE: IDE controller at PCI slot 0000:00:11.1 - [17179572.480000] ACPI: PCI Interrupt 0000:00:11.1[A]: no GSI - [17179572.480000] VP_IDE: chipset revision 6 - [17179572.480000] VP_IDE: not 100% native mode: will probe irqs later - [17179572.480000] VP_IDE: VIA vt8235 (rev 00) IDE UDMA133 controller on pci0000:00:11.1 - [17179572.480000] ide0: BM-DMA at 0x1860-0x1867, BIOS settings: hda:DMA, hdb:pio - [17179572.480000] ide1: BM-DMA at 0x1868-0x186f, BIOS settings: hdc:DMA, hdd:pio - [17179572.480000] Probing IDE interface ide0... - [17179572.900000] hda: IC25N080ATMR04-0, ATA DISK drive - [17179573.572000] ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 - [17179573.596000] Probing IDE interface ide1... - [17179574.460000] hdc: MATSHITADVD-RAM UJ-835S, ATAPI CD/DVD-ROM drive - [17179574.796000] ide1 at 0x170-0x177,0x376 on irq 15 - [17179574.800000] hda: max request size: 1024KiB - [17179574.808000] hda: 156301488 sectors (80026 MB) w/7884KiB Cache, CHS=16383/255/63, UDMA(100) - [17179574.808000] hda: cache flushes supported - [17179574.808000] hda: hda1 hda2 hda3 - [17179574.844000] hdc: ATAPI 24X DVD-ROM DVD-R-RAM CD-R/RW drive, 2048kB Cache, UDMA(33) - [17179574.844000] Uniform CD-ROM driver Revision: 3.20 - [17179575.236000] ieee1394: Initialized config rom entry `ip1394' - [17179575.244000] usbcore: registered new driver usbfs - [17179575.244000] usbcore: registered new driver hub - [17179575.248000] USB Universal Host Controller Interface driver v2.3 - [17179575.248000] ACPI: PCI Interrupt 0000:00:10.0[A] -> GSI 21 (level, low) -> IRQ 177 - [17179575.248000] PCI: VIA IRQ fixup for 0000:00:10.0, from 0 to 1 - [17179575.248000] uhci_hcd 0000:00:10.0: UHCI Host Controller - [17179575.248000] uhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 1 - [17179575.248000] uhci_hcd 0000:00:10.0: irq 177, io base 0x00001800 - [17179575.248000] hub 1-0:1.0: USB hub found - [17179575.248000] hub 1-0:1.0: 2 ports detected - [17179575.312000] ohci1394: $Rev: 1313 $ Ben Collins <[EMAIL PROTECTED]> - [17179575.312000] ACPI: PCI Interrupt 0000:00:07.1[B] -> GSI 18 (level, low) -> IRQ 185 - [17179575.352000] ACPI: PCI Interrupt 0000:00:10.1[B] -> GSI 21 (level, low) -> IRQ 177 - [17179575.352000] PCI: VIA IRQ fixup for 0000:00:10.1, from 0 to 1 - [17179575.352000] uhci_hcd 0000:00:10.1: UHCI Host Controller - [17179575.352000] uhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 2 - [17179575.352000] uhci_hcd 0000:00:10.1: irq 177, io base 0x00001820 - [17179575.352000] hub 2-0:1.0: USB hub found - [17179575.352000] hub 2-0:1.0: 2 ports detected - [17179575.360000] ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[185] MMIO=[d0015000-d00157ff] Max Packet=[2048] - [17179575.456000] ACPI: PCI Interrupt 0000:00:10.2[C] -> GSI 21 (level, low) -> IRQ 177 - [17179575.456000] PCI: VIA IRQ fixup for 0000:00:10.2, from 0 to 1 - [17179575.456000] uhci_hcd 0000:00:10.2: UHCI Host Controller - [17179575.456000] uhci_hcd 0000:00:10.2: new USB bus registered, assigned bus number 3 - [17179575.456000] uhci_hcd 0000:00:10.2: irq 177, io base 0x00001840 - [17179575.456000] hub 3-0:1.0: USB hub found - [17179575.456000] hub 3-0:1.0: 2 ports detected - [17179575.560000] ACPI: PCI Interrupt 0000:00:10.3[D] -> GSI 21 (level, low) -> IRQ 177 - [17179575.560000] ehci_hcd 0000:00:10.3: EHCI Host Controller - [17179575.560000] ehci_hcd 0000:00:10.3: new USB bus registered, assigned bus number 4 - [17179575.560000] ehci_hcd 0000:00:10.3: irq 177, io mem 0xd0015800 - [17179575.560000] ehci_hcd 0000:00:10.3: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 - [17179575.560000] hub 4-0:1.0: USB hub found - [17179575.560000] hub 4-0:1.0: 6 ports detected - [17179575.592000] usb 1-1: new full speed USB device using uhci_hcd and address 2 - [17179575.848000] Attempting manual resume - [17179575.904000] EXT3-fs: INFO: recovery required on readonly filesystem. - [17179575.904000] EXT3-fs: write access will be enabled during recovery. - [17179576.536000] usb 4-1: new high speed USB device using ehci_hcd and address 2 - [17179576.632000] ieee1394: Host added: ID:BUS[0-00:1023] GUID[00c09f00004fe9cf] - [17179576.668000] hub 4-1:1.0: USB hub found - [17179576.668000] hub 4-1:1.0: 4 ports detected - [17179577.312000] usb 3-1: new full speed USB device using uhci_hcd and address 2 - [17179577.464000] SCSI subsystem initialized - [17179577.464000] Initializing USB Mass Storage driver... - [17179577.464000] scsi0 : SCSI emulation for USB Mass Storage devices - [17179577.464000] usb-storage: device found at 2 - [17179577.464000] usb-storage: waiting for device to settle before scanning - [17179577.464000] usbcore: registered new driver usb-storage - [17179577.464000] USB Mass Storage support registered. - [17179577.508000] EXT3-fs: hda1: orphan cleanup on readonly fs - [17179577.508000] kjournald starting. Commit interval 5 seconds - [17179577.556000] ext3_orphan_cleanup: deleting unreferenced inode 2879291 - [17179577.556000] ext3_orphan_cleanup: deleting unreferenced inode 1897467 - [17179577.556000] ext3_orphan_cleanup: deleting unreferenced inode 2878966 - [17179577.588000] ext3_orphan_cleanup: deleting unreferenced inode 2878927 - [17179577.588000] EXT3-fs: hda1: 4 orphan inodes deleted - [17179577.588000] EXT3-fs: recovery complete. - [17179577.948000] EXT3-fs: mounted filesystem with ordered data mode. - [17179582.468000] Vendor: Generic Model: Flash R/W Rev: 2002 - [17179582.468000] Type: Direct-Access ANSI SCSI revision: 02 - [17179582.468000] usb-storage: device scan complete - [17179590.740000] Driver 'sd' needs updating - please use bus_type methods - [17179590.756000] sd 0:0:0:0: Attached scsi removable disk sda - [17179590.764000] sd 0:0:0:0: Attached scsi generic sg0 type 0 - [17179591.980000] pci_hotplug: PCI Hot Plug PCI Core version: 0.5 - [17179592.016000] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4 - [17179592.032000] Linux agpgart interface v0.101 (c) Dave Jones - [17179592.064000] agpgart: Detected AGP bridge 0 - [17179592.076000] agpgart: AGP aperture is 256M @ 0xe0000000 - [17179592.112000] ACPI: PCI Interrupt 0000:00:07.0[A] -> GSI 17 (level, low) -> IRQ 169 - [17179592.112000] Yenta: CardBus bridge found at 0000:00:07.0 [1025:0057] - [17179592.112000] Yenta: Using CSCINT to route CSC interrupts to PCI - [17179592.112000] Yenta: Routing CardBus interrupts to PCI - [17179592.112000] Yenta TI: socket 0000:00:07.0, mfunc 0x007c1b22, devctl 0x44 - [17179592.148000] ieee80211_1_1_13_crypt: registered algorithm 'NULL' - [17179592.168000] ieee80211_1_1_13: 802.11 data/management/control stack, 1.1.13 - [17179592.168000] ieee80211_1_1_13: Copyright (C) 2004-2005 Intel Corporation <[EMAIL PROTECTED]> - [17179592.176000] ieee80211_crypt: registered algorithm 'NULL' - [17179592.176000] ieee80211: 802.11 data/management/control stack, git-1.1.7 - [17179592.176000] ieee80211: Copyright (C) 2004-2005 Intel Corporation <[EMAIL PROTECTED]> - [17179592.344000] Yenta: ISA IRQ mask 0x0af8, PCI irq 169 - [17179592.344000] Socket status: 30000086 - [17179592.572000] tg3.c:v3.47 (Dec 28, 2005) - [17179592.572000] ACPI: PCI Interrupt 0000:00:0b.0[A] -> GSI 17 (level, low) -> IRQ 169 - [17179592.596000] eth0: Tigon3 [partno(BCM95788A50) rev 3003 PHY(5705)] (PCI:33MHz:32-bit) 10/100/1000BaseT Ethernet 00:c0:9f:93:5d:0b - [17179592.596000] eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] Split[0] WireSpeed[0] TSOcap[1] - [17179592.596000] eth0: dma_rwctrl[763f0000] - [17179592.648000] ipw2200: Intel(R) PRO/Wireless 2200/2915 Network Driver, 1.1.1 - [17179592.648000] ipw2200: Copyright(c) 2003-2006 Intel Corporation - [17179592.648000] Warning: PCI driver ipw2200 has a struct device_driver shutdown method, please update! - [17179592.648000] ACPI: PCI Interrupt 0000:00:09.0[A] -> GSI 19 (level, low) -> IRQ 193 - [17179592.648000] ipw2200: Detected Intel PRO/Wireless 2200BG Network Connection - [17179592.724000] input: PC Speaker as /class/input/input1 - [17179592.860000] Synaptics Touchpad, model: 1, fw: 5.8, id: 0x9d48b1, caps: 0x904713/0x4006 - [17179592.896000] input: SynPS/2 Synaptics TouchPad as /class/input/input2 - [17179593.096000] irda_init() - [17179593.096000] NET: Registered protocol family 23 - [17179593.108000] ipw2200: Detected geography ZZM (11 802.11bg channels, 0 802.11a channels) - [17179593.188000] ts: Compaq touchscreen protocol output - [17179593.416000] cs: IO port probe 0x100-0x3af: clean. - [17179593.416000] cs: IO port probe 0x3e0-0x4ff: clean. - [17179593.420000] cs: IO port probe 0x820-0x8ff: clean. - [17179593.420000] cs: IO port probe 0xc00-0xcf7: clean. - [17179593.420000] cs: IO port probe 0xa00-0xaff: clean. - [17179593.708000] ACPI: PCI Interrupt 0000:00:11.6[C] -> GSI 22 (level, low) -> IRQ 201 - [17179593.716000] PCI: Setting latency timer of device 0000:00:11.6 to 64 - [17179593.740000] ACPI: PCI Interrupt 0000:00:11.5[C] -> GSI 22 (level, low) -> IRQ 201 - [17179593.740000] PCI: Setting latency timer of device 0000:00:11.5 to 64 - [17179594.896000] lp: driver loaded but no devices found - [17179594.924000] sbp2: $Rev: 1306 $ Ben Collins <[EMAIL PROTECTED]> - [17179594.924000] ieee1394: sbp2: Driver forced to serialize I/O (serialize_io=1) - [17179594.924000] ieee1394: sbp2: Try serialize_io=0 for better performance - [17179595.308000] EXT3 FS on hda1, internal journal - [17179595.544000] md: md driver 0.90.3 MAX_MD_DEVS=256, MD_SB_DISKS=27 - [17179595.544000] md: bitmap version 4.39 - [17179596.140000] device-mapper: 4.4.0-ioctl (2005-01-12) initialised: [EMAIL PROTECTED] - [17179597.392000] HFS+-fs: write access to a jounaled filesystem is not supported, use the force option at your own risk, mounting read-only. - [17179598.924000] Adding 524280k swap on /mnt/512Mb.swap. Priority:-1 extents:150 across:536004k - [17179600.292000] ACPI: AC Adapter [ACAD] (on-line) - [17179600.296000] ACPI: Battery Slot [BAT1] (battery present) - [17179600.360000] ACPI: Power Button (FF) [PWRF] - [17179600.360000] ACPI: Power Button (CM) [PWRB] - [17179600.360000] ACPI: Lid Switch [LID] - [17179600.360000] ACPI: Sleep Button (CM) [SLPB] - [17179600.436000] ibm_acpi: ec object not found - [17179600.464000] pcc_acpi: loading... - [17179600.540000] ACPI: Video Device [VGA] (multi-head: yes rom: no post: no) - [17179601.044000] powernow-k8: Found 1 AMD Athlon 64 / Opteron processors (version 1.50.4) - [17179601.044000] powernow-k8: 0 : fid 0xc (2000 MHz), vid 0x8 (1350 mV) - [17179601.044000] powernow-k8: 1 : fid 0xa (1800 MHz), vid 0xc (1250 mV) - [17179601.044000] powernow-k8: 2 : fid 0x8 (1600 MHz), vid 0xe (1200 mV) - [17179601.044000] powernow-k8: 3 : fid 0x0 (800 MHz), vid 0x17 (975 mV) - [17179601.044000] cpu_init done, current fid 0xc, vid 0x8 - [17179606.280000] fglrx: module license 'Proprietary. (C) 2002 - ATI Technologies, Starnberg, GERMANY' taints kernel. - [17179606.284000] [fglrx] Maximum main memory to use for locked dma buffers: 430 MBytes. - [17179606.284000] [fglrx] module loaded - fglrx 8.25.18 [May 18 2006] on minor 0 - [17179606.412000] ACPI: PCI Interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 209 - [17179608.368000] [fglrx:drm_parse_option] *ERROR* "agplock" is not a valid option - [17179608.368000] [fglrx] Maximum main memory to use for locked dma buffers: 430 MBytes. - [17179608.368000] [fglrx] AGP detected, AgpState = 0x1f000a0b (hardware caps of chipset) - [17179608.368000] agpgart: Found an AGP 3.5 compliant device at 0000:00:00.0. - [17179608.368000] agpgart: Putting AGP V3 device at 0000:00:00.0 into 8x mode - [17179608.368000] agpgart: Putting AGP V3 device at 0000:01:00.0 into 8x mode - [17179608.368000] [fglrx] AGP enabled, AgpCommand = 0x1f000302 (selected caps) - [17179608.376000] [fglrx] total GART = 268435456 - [17179608.376000] [fglrx] free GART = 252440576 - [17179608.376000] [fglrx] max single GART = 252440576 - [17179608.376000] [fglrx] total LFB = 126169088 - [17179608.376000] [fglrx] free LFB = 114274304 - [17179608.376000] [fglrx] max single LFB = 114274304 - [17179608.376000] [fglrx] total Inv = 0 - [17179608.376000] [fglrx] free Inv = 0 - [17179608.376000] [fglrx] max single Inv = 0 - [17179608.376000] [fglrx] total TIM = 0 - [17179608.492000] ppdev: user-space parallel port driver - [17179608.684000] [fglrx] total GART = 268435456 - [17179608.684000] [fglrx] free GART = 252440576 - [17179608.684000] [fglrx] max single GART = 252440576 - [17179608.684000] [fglrx] total LFB = 126169088 - [17179608.684000] [fglrx] free LFB = 102719488 - [17179608.684000] [fglrx] max single LFB = 102719488 - [17179608.684000] [fglrx] total Inv = 0 - [17179608.684000] [fglrx] free Inv = 0 - [17179608.684000] [fglrx] max single Inv = 0 - [17179608.684000] [fglrx] total TIM = 0 - [17179609.436000] apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac) - [17179609.436000] apm: overridden by ACPI. - [17179615.364000] tg3: eth0: Link is up at 100 Mbps, full duplex. - [17179615.364000] tg3: eth0: Flow control is off for TX and off for RX. - [17179618.328000] NET: Registered protocol family 17 - [17179619.092000] NET: Registered protocol family 10 - [17179619.092000] lo: Disabled Privacy Extensions - [17179619.092000] IPv6 over IPv4 tunneling driver - [17179619.872000] Bluetooth: Core ver 2.8 - [17179619.872000] NET: Registered protocol family 31 - [17179619.872000] Bluetooth: HCI device and connection manager initialized - [17179619.872000] Bluetooth: HCI socket layer initialized - [17179619.928000] Bluetooth: L2CAP ver 2.8 - [17179619.928000] Bluetooth: L2CAP socket layer initialized - [17179620.108000] Bluetooth: RFCOMM socket layer initialized - [17179620.108000] Bluetooth: RFCOMM TTY layer initialized - [17179620.108000] Bluetooth: RFCOMM ver 1.7 - [17179620.876000] /dev/vmmon[5113]: Module vmmon: registered with major=10 minor=165 - [17179620.876000] /dev/vmmon[5113]: Module vmmon: initialized - [17179621.148000] /dev/vmnet: open called by PID 5139 (vmnet-bridge) - [17179621.148000] /dev/vmnet: hub 0 does not exist, allocating memory. - [17179621.148000] /dev/vmnet: port on hub 0 successfully opened - [17179621.148000] bridge-eth0: enabling the bridge - [17179621.148000] bridge-eth0: up - [17179621.148000] bridge-eth0: already up - [17179621.148000] bridge-eth0: attached - [17179621.172000] /dev/vmnet: open called by PID 5154 (vmnet-netifup) - [17179621.172000] /dev/vmnet: hub 1 does not exist, allocating memory. - [17179621.176000] /dev/vmnet: port on hub 1 successfully opened - [17179621.180000] /dev/vmnet: open called by PID 5155 (vmnet-netifup) - [17179621.180000] /dev/vmnet: hub 8 does not exist, allocating memory. - [17179621.180000] /dev/vmnet: port on hub 8 successfully opened - [17179621.312000] /dev/vmnet: open called by PID 5153 (vmnet-natd) - [17179621.312000] /dev/vmnet: port on hub 8 successfully opened - [17179621.684000] /dev/vmnet: open called by PID 5172 (vmnet-dhcpd) - [17179621.684000] /dev/vmnet: port on hub 8 successfully opened - [17179621.688000] /dev/vmnet: open called by PID 5177 (vmnet-dhcpd) - [17179621.688000] /dev/vmnet: port on hub 1 successfully opened - [17179629.332000] eth1: no IPv6 routers present - [17179631.460000] vmnet8: no IPv6 routers present - [17179631.848000] vmnet1: no IPv6 routers present - [17179632.132000] eth0: no IPv6 routers present - [17211134.608000] SCSI device sda: 1953792 512-byte hdwr sectors (1000 MB) - [17211134.612000] sda: Write Protect is off - [17211134.612000] sda: Mode Sense: 03 00 00 00 - [17211134.612000] sda: assuming drive cache: write through - [17211134.624000] SCSI device sda: 1953792 512-byte hdwr sectors (1000 MB) - [17211134.628000] sda: Write Protect is off - [17211134.628000] sda: Mode Sense: 03 00 00 00 - [17211134.628000] sda: assuming drive cache: write through - [17211134.628000] sda: sda1 - [17211165.216000] usb 3-1: reset full speed USB device using uhci_hcd and address 2 - [17211165.464000] usb 3-1: reset full speed USB device using uhci_hcd and address 2 - [17211165.712000] usb 3-1: reset full speed USB device using uhci_hcd and address 2 - [17211165.960000] usb 3-1: reset full speed USB device using uhci_hcd and address 2 - [17211166.092000] sd 0:0:0:0: scsi: Device offlined - not ready after error recovery - [17211166.092000] sd 0:0:0:0: SCSI error: return code = 0x50000 - [17211166.092000] end_request: I/O error, dev sda, sector 1953785 - [17211166.092000] Buffer I/O error on device sda1, logical block 1953656 - [17211166.092000] sd 0:0:0:0: rejecting I/O to offline device - [17211166.092000] Buffer I/O error on device sda1, logical block 1953657 - [17211166.092000] Buffer I/O error on device sda1, logical block 1953658 - [17211166.092000] Buffer I/O error on device sda1, logical block 1953659 - [17211166.092000] Buffer I/O error on device sda1, logical block 1953660 - [17211166.092000] Buffer I/O error on device sda1, logical block 1953661 - [17211166.092000] Buffer I/O error on device sda1, logical block 1953662 - [17211166.092000] sd 0:0:0:0: rejecting I/O to offline device - [17211166.096000] sd 0:0:0:0: rejecting I/O to offline device - [17211166.096000] Buffer I/O error on device sda1, logical block 1953656 - [17211166.096000] Buffer I/O error on device sda1, logical block 1953657 - [17211166.096000] Buffer I/O error on device sda1, logical block 1953658 - [17211166.096000] sd 0:0:0:0: rejecting I/O to offline device - [17211166.100000] sd 0:0:0:0: rejecting I/O to offline device - [17211166.100000] sd 0:0:0:0: rejecting I/O to offline device - [17211166.100000] sd 0:0:0:0: rejecting I/O to offline device - [17211166.100000] sd 0:0:0:0: rejecting I/O to offline device - [17211166.100000] sd 0:0:0:0: rejecting I/O to offline device - [17211166.100000] sd 0:0:0:0: rejecting I/O to offline device - [17211166.100000] sd 0:0:0:0: rejecting I/O to offline device - [17211166.100000] sd 0:0:0:0: rejecting I/O to offline device - [17211166.100000] sd 0:0:0:0: rejecting I/O to offline device - [17211166.100000] sd 0:0:0:0: rejecting I/O to offline device - [17211166.100000] sd 0:0:0:0: rejecting I/O to offline device - [17211166.100000] sd 0:0:0:0: rejecting I/O to offline device - [17211166.100000] sd 0:0:0:0: rejecting I/O to offline device - [17211166.100000] sd 0:0:0:0: rejecting I/O to offline device - [17211166.100000] sd 0:0:0:0: rejecting I/O to offline device - [17211166.100000] sd 0:0:0:0: rejecting I/O to offline device - [17211166.100000] sd 0:0:0:0: rejecting I/O to offline device - [17211166.100000] sd 0:0:0:0: rejecting I/O to offline device - [17211166.100000] sd 0:0:0:0: rejecting I/O to offline device - [17211166.100000] sd 0:0:0:0: rejecting I/O to offline device - [17211166.100000] sd 0:0:0:0: rejecting I/O to offline device - [17211166.100000] sd 0:0:0:0: rejecting I/O to offline device - [17211166.100000] sd 0:0:0:0: rejecting I/O to offline device - [17211166.100000] sd 0:0:0:0: rejecting I/O to offline device - [17211166.100000] sd 0:0:0:0: rejecting I/O to offline device - [17211166.100000] sd 0:0:0:0: rejecting I/O to offline device - [17211166.100000] sd 0:0:0:0: rejecting I/O to offline device - [17211166.100000] sd 0:0:0:0: rejecting I/O to offline device - [17211166.100000] sd 0:0:0:0: rejecting I/O to offline device - [17211166.100000] sd 0:0:0:0: rejecting I/O to offline device - [17211166.100000] sd 0:0:0:0: rejecting I/O to offline device - [17211166.100000] sd 0:0:0:0: rejecting I/O to offline device - [17211166.100000] sd 0:0:0:0: rejecting I/O to offline device - [17211166.100000] sd 0:0:0:0: rejecting I/O to offline device - [17211166.100000] sd 0:0:0:0: rejecting I/O to offline device - - - lsusb -vv - - Bus 004 Device 002: ID 04b4:6560 Cypress Semiconductor Corp. CY7C65640 USB-2.0 "TetraHub" - Device Descriptor: - bLength 18 - bDescriptorType 1 - bcdUSB 2.00 - bDeviceClass 9 Hub - bDeviceSubClass 0 Unused - bDeviceProtocol 2 TT per port - bMaxPacketSize0 64 - idVendor 0x04b4 Cypress Semiconductor Corp. - idProduct 0x6560 CY7C65640 USB-2.0 "TetraHub" - bcdDevice 0.09 - iManufacturer 0 - iProduct 0 - iSerial 0 - bNumConfigurations 1 - Configuration Descriptor: - bLength 9 - bDescriptorType 2 - wTotalLength 41 - bNumInterfaces 1 - bConfigurationValue 1 - iConfiguration 0 - bmAttributes 0xe0 - Self Powered - Remote Wakeup - MaxPower 100mA - Interface Descriptor: - bLength 9 - bDescriptorType 4 - bInterfaceNumber 0 - bAlternateSetting 0 - bNumEndpoints 1 - bInterfaceClass 9 Hub - bInterfaceSubClass 0 Unused - bInterfaceProtocol 1 Single TT - iInterface 0 - Endpoint Descriptor: - bLength 7 - bDescriptorType 5 - bEndpointAddress 0x81 EP 1 IN - bmAttributes 3 - Transfer Type Interrupt - Synch Type None - Usage Type Data - wMaxPacketSize 0x0001 1x 1 bytes - bInterval 12 - Interface Descriptor: - bLength 9 - bDescriptorType 4 - bInterfaceNumber 0 - bAlternateSetting 1 - bNumEndpoints 1 - bInterfaceClass 9 Hub - bInterfaceSubClass 0 Unused - bInterfaceProtocol 2 TT per port - iInterface 0 - Endpoint Descriptor: - bLength 7 - bDescriptorType 5 - bEndpointAddress 0x81 EP 1 IN - bmAttributes 3 - Transfer Type Interrupt - Synch Type None - Usage Type Data - wMaxPacketSize 0x0001 1x 1 bytes - bInterval 12 - Hub Descriptor: - bLength 9 - bDescriptorType 41 - nNbrPorts 4 - wHubCharacteristic 0x0089 - Per-port power switching - Per-port overcurrent protection - TT think time 8 FS bits - Port indicators - bPwrOn2PwrGood 50 * 2 milli seconds - bHubContrCurrent 100 milli Ampere - DeviceRemovable 0x58 - PortPwrCtrlMask 0xc0 - Hub Port Status: - Port 1: 0000.0100 power - Port 2: 0000.0100 power - Port 3: 0000.0100 power - Port 4: 0000.0100 power - Device Qualifier (for other device speed): - bLength 10 - bDescriptorType 6 - bcdUSB 2.00 - bDeviceClass 9 Hub - bDeviceSubClass 0 Unused - bDeviceProtocol 0 - bMaxPacketSize0 64 - bNumConfigurations 1 - Device Status: 0x0001 - Self Powered - - Bus 004 Device 001: ID 0000:0000 - Device Descriptor: - bLength 18 - bDescriptorType 1 - bcdUSB 2.00 - bDeviceClass 9 Hub - bDeviceSubClass 0 Unused - bDeviceProtocol 1 Single TT - bMaxPacketSize0 64 - idVendor 0x0000 - idProduct 0x0000 - bcdDevice 2.06 - iManufacturer 3 Linux 2.6.15-26-686 ehci_hcd - iProduct 2 EHCI Host Controller - iSerial 1 0000:00:10.3 - bNumConfigurations 1 - Configuration Descriptor: - bLength 9 - bDescriptorType 2 - wTotalLength 25 - bNumInterfaces 1 - bConfigurationValue 1 - iConfiguration 0 - bmAttributes 0xc0 - Self Powered - MaxPower 0mA - Interface Descriptor: - bLength 9 - bDescriptorType 4 - bInterfaceNumber 0 - bAlternateSetting 0 - bNumEndpoints 1 - bInterfaceClass 9 Hub - bInterfaceSubClass 0 Unused - bInterfaceProtocol 0 - iInterface 0 - Endpoint Descriptor: - bLength 7 - bDescriptorType 5 - bEndpointAddress 0x81 EP 1 IN - bmAttributes 3 - Transfer Type Interrupt - Synch Type None - Usage Type Data - wMaxPacketSize 0x0002 1x 2 bytes - bInterval 12 - Hub Descriptor: - bLength 9 - bDescriptorType 41 - nNbrPorts 6 - wHubCharacteristic 0x000a - No power switching (usb 1.0) - Per-port overcurrent protection - TT think time 8 FS bits - bPwrOn2PwrGood 10 * 2 milli seconds - bHubContrCurrent 0 milli Ampere - DeviceRemovable 0x48 - PortPwrCtrlMask 0xc0 - Hub Port Status: - Port 1: 0000.0503 highspeed power enable connect - Port 2: 0000.0100 power - Port 3: 0000.0100 power - Port 4: 0000.0100 power - Port 5: 0000.0000 - Port 6: 0000.0100 power - Device Status: 0x0001 - Self Powered - - Bus 001 Device 001: ID 0000:0000 - Device Descriptor: - bLength 18 - bDescriptorType 1 - bcdUSB 1.10 - bDeviceClass 9 Hub - bDeviceSubClass 0 Unused - bDeviceProtocol 0 - bMaxPacketSize0 64 - idVendor 0x0000 - idProduct 0x0000 - bcdDevice 2.06 - iManufacturer 3 Linux 2.6.15-26-686 uhci_hcd - iProduct 2 UHCI Host Controller - iSerial 1 0000:00:10.0 - bNumConfigurations 1 - Configuration Descriptor: - bLength 9 - bDescriptorType 2 - wTotalLength 25 - bNumInterfaces 1 - bConfigurationValue 1 - iConfiguration 0 - bmAttributes 0xe0 - Self Powered - Remote Wakeup - MaxPower 0mA - Interface Descriptor: - bLength 9 - bDescriptorType 4 - bInterfaceNumber 0 - bAlternateSetting 0 - bNumEndpoints 1 - bInterfaceClass 9 Hub - bInterfaceSubClass 0 Unused - bInterfaceProtocol 0 - iInterface 0 - Endpoint Descriptor: - bLength 7 - bDescriptorType 5 - bEndpointAddress 0x81 EP 1 IN - bmAttributes 3 - Transfer Type Interrupt - Synch Type None - Usage Type Data - wMaxPacketSize 0x0002 1x 2 bytes - bInterval 255 - Hub Descriptor: - bLength 9 - bDescriptorType 41 - nNbrPorts 2 - wHubCharacteristic 0x000a - No power switching (usb 1.0) - Per-port overcurrent protection - bPwrOn2PwrGood 1 * 2 milli seconds - bHubContrCurrent 0 milli Ampere - DeviceRemovable 0x08 - PortPwrCtrlMask 0x82 - Hub Port Status: - Port 1: 0000.0100 power - Port 2: 0000.0100 power - Device Status: 0x0003 - Self Powered - Remote Wakeup Enabled - - Bus 003 Device 002: ID 0483:0321 SGS Thomson Microelectronics - Device Descriptor: - bLength 18 - bDescriptorType 1 - bcdUSB 1.10 - bDeviceClass 0 (Defined at Interface level) - bDeviceSubClass 0 - bDeviceProtocol 0 - bMaxPacketSize0 16 - idVendor 0x0483 SGS Thomson Microelectronics - idProduct 0x0321 - bcdDevice 1.92 - iManufacturer 1 Generic - iProduct 2 USB Mass Storage Device - iSerial 3 7777777777777777 - bNumConfigurations 1 - Configuration Descriptor: - bLength 9 - bDescriptorType 2 - wTotalLength 32 - bNumInterfaces 1 - bConfigurationValue 1 - iConfiguration 0 - bmAttributes 0x80 - (Bus Powered) - MaxPower 100mA - Interface Descriptor: - bLength 9 - bDescriptorType 4 - bInterfaceNumber 0 - bAlternateSetting 0 - bNumEndpoints 2 - bInterfaceClass 8 Mass Storage - bInterfaceSubClass 6 SCSI - bInterfaceProtocol 80 Bulk (Zip) - iInterface 4 4in1 - Endpoint Descriptor: - bLength 7 - bDescriptorType 5 - bEndpointAddress 0x82 EP 2 IN - bmAttributes 2 - Transfer Type Bulk - Synch Type None - Usage Type Data - wMaxPacketSize 0x0040 1x 64 bytes - bInterval 0 - Endpoint Descriptor: - bLength 7 - bDescriptorType 5 - bEndpointAddress 0x02 EP 2 OUT - bmAttributes 2 - Transfer Type Bulk - Synch Type None - Usage Type Data - wMaxPacketSize 0x0040 1x 64 bytes - bInterval 0 - Device Status: 0x0000 - (Bus Powered) - - Bus 003 Device 001: ID 0000:0000 - Device Descriptor: - bLength 18 - bDescriptorType 1 - bcdUSB 1.10 - bDeviceClass 9 Hub - bDeviceSubClass 0 Unused - bDeviceProtocol 0 - bMaxPacketSize0 64 - idVendor 0x0000 - idProduct 0x0000 - bcdDevice 2.06 - iManufacturer 3 Linux 2.6.15-26-686 uhci_hcd - iProduct 2 UHCI Host Controller - iSerial 1 0000:00:10.2 - bNumConfigurations 1 - Configuration Descriptor: - bLength 9 - bDescriptorType 2 - wTotalLength 25 - bNumInterfaces 1 - bConfigurationValue 1 - iConfiguration 0 - bmAttributes 0xe0 - Self Powered - Remote Wakeup - MaxPower 0mA - Interface Descriptor: - bLength 9 - bDescriptorType 4 - bInterfaceNumber 0 - bAlternateSetting 0 - bNumEndpoints 1 - bInterfaceClass 9 Hub - bInterfaceSubClass 0 Unused - bInterfaceProtocol 0 - iInterface 0 - Endpoint Descriptor: - bLength 7 - bDescriptorType 5 - bEndpointAddress 0x81 EP 1 IN - bmAttributes 3 - Transfer Type Interrupt - Synch Type None - Usage Type Data - wMaxPacketSize 0x0002 1x 2 bytes - bInterval 255 - Hub Descriptor: - bLength 9 - bDescriptorType 41 - nNbrPorts 2 - wHubCharacteristic 0x000a - No power switching (usb 1.0) - Per-port overcurrent protection - bPwrOn2PwrGood 1 * 2 milli seconds - bHubContrCurrent 0 milli Ampere - DeviceRemovable 0x78 - PortPwrCtrlMask 0x01 - Hub Port Status: - Port 1: 0000.0103 power enable connect - Port 2: 0000.0300 lowspeed power - Device Status: 0x0003 - Self Powered - Remote Wakeup Enabled - - Bus 002 Device 001: ID 0000:0000 - Device Descriptor: - bLength 18 - bDescriptorType 1 - bcdUSB 1.10 - bDeviceClass 9 Hub - bDeviceSubClass 0 Unused - bDeviceProtocol 0 - bMaxPacketSize0 64 - idVendor 0x0000 - idProduct 0x0000 - bcdDevice 2.06 - iManufacturer 3 Linux 2.6.15-26-686 uhci_hcd - iProduct 2 UHCI Host Controller - iSerial 1 0000:00:10.1 - bNumConfigurations 1 - Configuration Descriptor: - bLength 9 - bDescriptorType 2 - wTotalLength 25 - bNumInterfaces 1 - bConfigurationValue 1 - iConfiguration 0 - bmAttributes 0xe0 - Self Powered - Remote Wakeup - MaxPower 0mA - Interface Descriptor: - bLength 9 - bDescriptorType 4 - bInterfaceNumber 0 - bAlternateSetting 0 - bNumEndpoints 1 - bInterfaceClass 9 Hub - bInterfaceSubClass 0 Unused - bInterfaceProtocol 0 - iInterface 0 - Endpoint Descriptor: - bLength 7 - bDescriptorType 5 - bEndpointAddress 0x81 EP 1 IN - bmAttributes 3 - Transfer Type Interrupt - Synch Type None - Usage Type Data - wMaxPacketSize 0x0002 1x 2 bytes - bInterval 255 - Hub Descriptor: - bLength 9 - bDescriptorType 41 - nNbrPorts 2 - wHubCharacteristic 0x000a - No power switching (usb 1.0) - Per-port overcurrent protection - bPwrOn2PwrGood 1 * 2 milli seconds - bHubContrCurrent 0 milli Ampere - DeviceRemovable 0xf0 - PortPwrCtrlMask 0x01 - Hub Port Status: - Port 1: 0000.0300 lowspeed power - Port 2: 0000.0300 lowspeed power - Device Status: 0x0003 - Self Powered - Remote Wakeup Enabled - - lspci -vv - - 0000:00:00.0 Host bridge: VIA Technologies, Inc. VT8385 [K8T800 AGP] Host Bridge (rev 01) - Subsystem: VIA Technologies, Inc. VT8385 [K8T800 AGP] Host Bridge - Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- - Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR- - Latency: 8 - Region 0: Memory at e0000000 (32-bit, prefetchable) [size=256M] - Capabilities: [80] AGP version 3.5 - Status: RQ=32 Iso- ArqSz=0 Cal=2 SBA+ ITACoh- GART64- HTrans- 64bit- FW- AGP3+ Rate=x4,x8 - Command: RQ=1 ArqSz=0 Cal=0 SBA+ AGP+ GART64- 64bit- FW- Rate=x8 - Capabilities: [c0] #08 [0060] - Capabilities: [68] Power Management version 2 - Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) - Status: D0 PME-Enable- DSel=0 DScale=0 PME- - Capabilities: [58] #08 [8001] - - 0000:00:01.0 PCI bridge: VIA Technologies, Inc. VT8237 PCI bridge [K8T800/K8T890 South] (prog-if 00 [Normal decode]) - Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- - Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- - Latency: 0 - Bus: primary=00, secondary=01, subordinate=01, sec-latency=0 - I/O behind bridge: 00002000-00002fff - Memory behind bridge: d0100000-d01fffff - Prefetchable memory behind bridge: d8000000-dfffffff - BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B- - Capabilities: [80] Power Management version 2 - Flags: PMEClk- DSI- D1+ D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) - Status: D0 PME-Enable- DSel=0 DScale=0 PME- - - 0000:00:07.0 CardBus bridge: Texas Instruments PCI4510 PC card Cardbus Controller (rev 02) - Subsystem: Acer Incorporated [ALI]: Unknown device 0057 - Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- - Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- - Latency: 168, Cache Line Size: 0x08 (32 bytes) - Interrupt: pin A routed to IRQ 169 - Region 0: Memory at 34000000 (32-bit, non-prefetchable) [size=4K] - Bus: primary=00, secondary=02, subordinate=05, sec-latency=176 - Memory window 0: 30000000-31fff000 (prefetchable) - Memory window 1: 32000000-33fff000 - I/O window 0: 00001c00-00001cff - I/O window 1: 00003000-000030ff - BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset+ 16bInt+ PostWrite+ - 16-bit legacy interface ports at 0001 - - 0000:00:07.1 FireWire (IEEE 1394): Texas Instruments PCI4510 IEEE-1394 Controller (prog-if 10 [OHCI]) - Subsystem: Acer Incorporated [ALI]: Unknown device 0057 - Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- - Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- - Latency: 64 (750ns min, 1000ns max), Cache Line Size: 0x10 (64 bytes) - Interrupt: pin B routed to IRQ 185 - Region 0: Memory at d0015000 (32-bit, non-prefetchable) [size=2K] - Region 1: Memory at d0010000 (32-bit, non-prefetchable) [size=16K] - Capabilities: [44] Power Management version 2 - Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-) - Status: D0 PME-Enable- DSel=0 DScale=0 PME+ - - 0000:00:09.0 Network controller: Intel Corporation PRO/Wireless 2200BG (rev 05) - Subsystem: Intel Corporation: Unknown device 2721 - Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- - Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- - Latency: 64 (750ns min, 6000ns max), Cache Line Size: 0x10 (64 bytes) - Interrupt: pin A routed to IRQ 193 - Region 0: Memory at d0014000 (32-bit, non-prefetchable) [size=4K] - Capabilities: [dc] Power Management version 2 - Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+) - Status: D0 PME-Enable- DSel=0 DScale=1 PME- - - 0000:00:0b.0 Ethernet controller: Broadcom Corporation NetXtreme BCM5788 Gigabit Ethernet (rev 03) - Subsystem: Acer Incorporated [ALI]: Unknown device 0057 - Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- - Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- - Latency: 64 (16000ns min), Cache Line Size: 0x10 (64 bytes) - Interrupt: pin A routed to IRQ 169 - Region 0: Memory at d0000000 (32-bit, non-prefetchable) [size=64K] - Capabilities: [48] Power Management version 2 - Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold+) - Status: D0 PME-Enable- DSel=0 DScale=1 PME- - Capabilities: [50] Vital Product Data - Capabilities: [58] Message Signalled Interrupts: 64bit+ Queue=0/3 Enable- - Address: ffefbfddfe7fc7fc Data: fb7f - - 0000:00:10.0 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 80) (prog-if 00 [UHCI]) - Subsystem: Acer Incorporated [ALI]: Unknown device 0057 - Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- - Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- - Latency: 64, Cache Line Size: 0x10 (64 bytes) - Interrupt: pin A routed to IRQ 177 - Region 4: I/O ports at 1800 [size=32] - Capabilities: [80] Power Management version 2 - Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+) - Status: D0 PME-Enable- DSel=0 DScale=0 PME+ - - 0000:00:10.1 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 80) (prog-if 00 [UHCI]) - Subsystem: Acer Incorporated [ALI]: Unknown device 0057 - Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- - Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- - Latency: 64, Cache Line Size: 0x10 (64 bytes) - Interrupt: pin B routed to IRQ 177 - Region 4: I/O ports at 1820 [size=32] - Capabilities: [80] Power Management version 2 - Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+) - Status: D0 PME-Enable- DSel=0 DScale=0 PME- - - 0000:00:10.2 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 80) (prog-if 00 [UHCI]) - Subsystem: Acer Incorporated [ALI]: Unknown device 0057 - Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- - Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- - Latency: 64, Cache Line Size: 0x10 (64 bytes) - Interrupt: pin C routed to IRQ 177 - Region 4: I/O ports at 1840 [size=32] - Capabilities: [80] Power Management version 2 - Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+) - Status: D0 PME-Enable- DSel=0 DScale=0 PME- - - 0000:00:10.3 USB Controller: VIA Technologies, Inc. USB 2.0 (rev 82) (prog-if 20 [EHCI]) - Subsystem: Acer Incorporated [ALI]: Unknown device 0057 - Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- - Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- - Latency: 64, Cache Line Size: 0x10 (64 bytes) - Interrupt: pin D routed to IRQ 177 - Region 0: Memory at d0015800 (32-bit, non-prefetchable) [size=256] - Capabilities: [80] Power Management version 2 - Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+) - Status: D0 PME-Enable- DSel=0 DScale=0 PME- - - 0000:00:11.0 ISA bridge: VIA Technologies, Inc. VT8235 ISA Bridge - Subsystem: Acer Incorporated [ALI]: Unknown device 0057 - Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B- - Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- - Latency: 0 - Capabilities: [c0] Power Management version 2 - Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) - Status: D0 PME-Enable- DSel=0 DScale=0 PME- - - 0000:00:11.1 IDE interface: VIA Technologies, Inc. VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE (rev 06) (prog-if 8a [Master SecP PriP]) - Subsystem: Acer Incorporated [ALI]: Unknown device 0057 - Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- - Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- - Latency: 64 - Interrupt: pin A routed to IRQ 0 - Region 4: I/O ports at 1860 [size=16] - Capabilities: [c0] Power Management version 2 - Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) - Status: D0 PME-Enable- DSel=0 DScale=0 PME- - - 0000:00:11.5 Multimedia audio controller: VIA Technologies, Inc. VT8233/A/8235/8237 AC97 Audio Controller (rev 50) - Subsystem: Acer Incorporated [ALI]: Unknown device 0057 - Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- - Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- - Interrupt: pin C routed to IRQ 201 - Region 0: I/O ports at 1000 [size=256] - Capabilities: [c0] Power Management version 2 - Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) - Status: D0 PME-Enable- DSel=0 DScale=0 PME- - - 0000:00:11.6 Communication controller: VIA Technologies, Inc. AC'97 Modem Controller (rev 80) - Subsystem: Acer Incorporated [ALI]: Unknown device 0057 - Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- - Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- - Interrupt: pin C routed to IRQ 201 - Region 0: I/O ports at 1400 [size=256] - Capabilities: [d0] Power Management version 2 - Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) - Status: D0 PME-Enable- DSel=0 DScale=0 PME- - - 0000:00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration - Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- - Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- - Capabilities: [80] #08 [2101] - - 0000:00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map - Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- - Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- - - 0000:00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller - Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- - Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- - - 0000:00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control - Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- - Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- - - 0000:01:00.0 VGA compatible controller: ATI Technologies Inc RV350 [Mobility Radeon 9600 M10] (prog-if 00 [VGA]) - Subsystem: Acer Incorporated [ALI]: Unknown device 0057 - Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- - Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- - Latency: 255 (2000ns min), Cache Line Size: 0x10 (64 bytes) - Interrupt: pin A routed to IRQ 209 - Region 0: Memory at d8000000 (32-bit, prefetchable) [size=128M] - Region 1: I/O ports at 2000 [size=256] - Region 2: Memory at d0100000 (32-bit, non-prefetchable) [size=64K] - Expansion ROM at d0120000 [disabled] [size=128K] - Capabilities: [58] AGP version 3.0 - Status: RQ=256 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans- 64bit- FW+ AGP3+ Rate=x4,x8 - Command: RQ=32 ArqSz=0 Cal=0 SBA+ AGP+ GART64- 64bit- FW- Rate=x8 - Capabilities: [50] Power Management version 2 - Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) - Status: D0 PME-Enable- DSel=0 DScale=0 PME-
** Attachment added: "lsusb" http://librarian.launchpad.net/4292735/lsusb.txt -- SGS Thomson 5in1 card reader not mounting sd https://launchpad.net/bugs/60963 -- ubuntu-bugs mailing list [email protected] https://lists.ubuntu.com/mailman/listinfo/ubuntu-bugs
