Here you go hope this helps,

[EMAIL PROTECTED]:~$ sudo lspci -vvnn
00:00.0 Host bridge [0600]: Intel Corporation Mobile PM965/GM965/GL960
Memory Controller Hub [8086:2a00] (rev 0c)
        Subsystem: Dell Unknown device [1028:01f2]
        Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
        Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort+ >SERR- <PERR-
        Latency: 0
        Capabilities: [e0] Vendor Specific Information

00:01.0 PCI bridge [0604]: Intel Corporation Mobile PM965/GM965/GL960 PCI
Express Root Port [8086:2a01] (rev 0c) (prog-if 00 [Normal decode])
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
        Latency: 0, Cache Line Size: 64 bytes
        Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
        I/O behind bridge: 0000e000-0000efff
        Memory behind bridge: fa000000-feafffff
        Prefetchable memory behind bridge: 00000000f4000000-00000000f7ffffff
        Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- <SERR- <PERR-
        BridgeCtl: Parity- SERR+ NoISA- VGA+ MAbort- >Reset- FastB2B-
        Capabilities: [88] Subsystem: Dell Unknown device [1028:01f2]
        Capabilities: [80] Power Management version 3
                Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-
        Capabilities: [90] Message Signalled Interrupts: Mask- 64bit-
Queue=0/0 Enable+
                Address: fee0300c  Data: 41c1
        Capabilities: [a0] Express Root Port (Slot+) IRQ 0
                Device: Supported: MaxPayload 128 bytes, PhantFunc 0,
ExtTag-
                Device: Latency L0s <64ns, L1 <1us
                Device: Errors: Correctable+ Non-Fatal+ Fatal+ Unsupported+
                Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
                Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
                Link: Supported Speed 2.5Gb/s, Width x16, ASPM L0s L1, Port
2
                Link: Latency L0s <256ns, L1 <4us
                Link: ASPM L0s L1 Enabled RCB 64 bytes CommClk+ ExtSynch-
                Link: Speed 2.5Gb/s, Width x16
                Slot: AtnBtn- PwrCtrl- MRL- AtnInd- PwrInd- HotPlug+
Surpise-
                Slot: Number 1, PowerLimit 75.000000
                Slot: Enabled AtnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq-
                Slot: AttnInd Off, PwrInd On, Power-
                Root: Correctable- Non-Fatal- Fatal- PME-

00:1a.0 USB Controller [0c03]: Intel Corporation 82801H (ICH8 Family) USB
UHCI Contoller #4 [8086:2834] (rev 02) (prog-if 00 [UHCI])
        Subsystem: Dell Unknown device [1028:01f2]
        Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
        Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
        Latency: 0
        Interrupt: pin A routed to IRQ 19
        Region 4: I/O ports at 6f20 [size=32]

00:1a.1 USB Controller [0c03]: Intel Corporation 82801H (ICH8 Family) USB
UHCI Controller #5 [8086:2835] (rev 02) (prog-if 00 [UHCI])
        Subsystem: Dell Unknown device [1028:01f2]
        Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
        Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
        Latency: 0
        Interrupt: pin B routed to IRQ 20
        Region 4: I/O ports at 6f00 [size=32]

00:1a.7 USB Controller [0c03]: Intel Corporation 82801H (ICH8 Family) USB2
EHCI Controller #2 [8086:283a] (rev 02) (prog-if 20 [EHCI])
        Subsystem: Dell Unknown device [1028:01f2]
        Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
        Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
        Latency: 0
        Interrupt: pin C routed to IRQ 21
        Region 0: Memory at fed1c400 (32-bit, non-prefetchable) [size=1K]
        Capabilities: [50] Power Management version 2
                Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-
        Capabilities: [58] Debug port

00:1b.0 Audio device [0403]: Intel Corporation 82801H (ICH8 Family) HD Audio
Controller [8086:284b] (rev 02)
        Subsystem: Dell Unknown device [1028:01f2]
        Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
        Interrupt: pin A routed to IRQ 20
        Region 0: Memory at febfc000 (64-bit, non-prefetchable) [size=16K]
        Capabilities: [50] Power Management version 2
                Flags: PMEClk- DSI- D1- D2- AuxCurrent=55mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-
        Capabilities: [60] Message Signalled Interrupts: Mask- 64bit+
Queue=0/0 Enable-
                Address: 0000000000000000  Data: 0000
        Capabilities: [70] Express Unknown type IRQ 0
                Device: Supported: MaxPayload 128 bytes, PhantFunc 0,
ExtTag-
                Device: Latency L0s unlimited, L1 unlimited
                Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
                Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+
                Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
                Link: Supported Speed unknown, Width x0, ASPM unknown, Port
0
                Link: Latency L0s <64ns, L1 <1us
                Link: ASPM Disabled CommClk- ExtSynch-
                Link: Speed unknown, Width x0

00:1c.0 PCI bridge [0604]: Intel Corporation 82801H (ICH8 Family) PCI
Express Port 1 [8086:283f] (rev 02) (prog-if 00 [Normal decode])
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
        Latency: 0, Cache Line Size: 64 bytes
        Bus: primary=00, secondary=0b, subordinate=0b, sec-latency=0
        Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort+ <SERR- <PERR-
        BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
        Capabilities: [40] Express Root Port (Slot+) IRQ 0
                Device: Supported: MaxPayload 128 bytes, PhantFunc 0,
ExtTag-
                Device: Latency L0s unlimited, L1 unlimited
                Device: Errors: Correctable+ Non-Fatal+ Fatal+ Unsupported+
                Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
                Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
                Link: Supported Speed 2.5Gb/s, Width x1, ASPM L0s L1, Port 1
                Link: Latency L0s <1us, L1 <4us
                Link: ASPM Disabled RCB 64 bytes CommClk- ExtSynch-
                Link: Speed 2.5Gb/s, Width x0
                Slot: AtnBtn- PwrCtrl- MRL- AtnInd- PwrInd- HotPlug+
Surpise+
                Slot: Number 2, PowerLimit 6.500000
                Slot: Enabled AtnBtn- PwrFlt- MRL- PresDet+ CmdCplt- HPIrq-
                Slot: AttnInd Unknown, PwrInd Unknown, Power-
                Root: Correctable- Non-Fatal- Fatal- PME-
        Capabilities: [80] Message Signalled Interrupts: Mask- 64bit-
Queue=0/0 Enable+
                Address: fee0300c  Data: 41c9
        Capabilities: [90] Subsystem: Dell Unknown device [1028:01f2]
        Capabilities: [a0] Power Management version 2
                Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:1c.1 PCI bridge [0604]: Intel Corporation 82801H (ICH8 Family) PCI
Express Port 2 [8086:2841] (rev 02) (prog-if 00 [Normal decode])
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
        Latency: 0, Cache Line Size: 64 bytes
        Bus: primary=00, secondary=0c, subordinate=0c, sec-latency=0
        Memory behind bridge: f9f00000-f9ffffff
        Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort+ <SERR- <PERR-
        BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
        Capabilities: [40] Express Root Port (Slot+) IRQ 0
                Device: Supported: MaxPayload 128 bytes, PhantFunc 0,
ExtTag-
                Device: Latency L0s unlimited, L1 unlimited
                Device: Errors: Correctable+ Non-Fatal+ Fatal+ Unsupported+
                Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
                Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
                Link: Supported Speed 2.5Gb/s, Width x1, ASPM L0s L1, Port 2
                Link: Latency L0s <256ns, L1 <4us
                Link: ASPM L1 Enabled RCB 64 bytes CommClk+ ExtSynch-
                Link: Speed 2.5Gb/s, Width x1
                Slot: AtnBtn- PwrCtrl- MRL- AtnInd- PwrInd- HotPlug+
Surpise+
                Slot: Number 3, PowerLimit 6.500000
                Slot: Enabled AtnBtn- PwrFlt- MRL- PresDet+ CmdCplt- HPIrq-
                Slot: AttnInd Unknown, PwrInd Unknown, Power-
                Root: Correctable- Non-Fatal- Fatal- PME-
        Capabilities: [80] Message Signalled Interrupts: Mask- 64bit-
Queue=0/0 Enable+
                Address: fee0300c  Data: 41d1
        Capabilities: [90] Subsystem: Dell Unknown device [1028:01f2]
        Capabilities: [a0] Power Management version 2
                Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:1c.3 PCI bridge [0604]: Intel Corporation 82801H (ICH8 Family) PCI
Express Port 4 [8086:2845] (rev 02) (prog-if 00 [Normal decode])
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
        Latency: 0, Cache Line Size: 64 bytes
        Bus: primary=00, secondary=0d, subordinate=0e, sec-latency=0
        I/O behind bridge: 0000d000-0000dfff
        Memory behind bridge: f9c00000-f9efffff
        Prefetchable memory behind bridge: 00000000f8000000-00000000f81fffff
        Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- <SERR- <PERR-
        BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
        Capabilities: [40] Express Root Port (Slot+) IRQ 0
                Device: Supported: MaxPayload 128 bytes, PhantFunc 0,
ExtTag-
                Device: Latency L0s unlimited, L1 unlimited
                Device: Errors: Correctable+ Non-Fatal+ Fatal+ Unsupported+
                Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
                Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
                Link: Supported Speed 2.5Gb/s, Width x1, ASPM L0s L1, Port 4
                Link: Latency L0s <1us, L1 <4us
                Link: ASPM Disabled RCB 64 bytes CommClk- ExtSynch-
                Link: Speed 2.5Gb/s, Width x0
                Slot: AtnBtn- PwrCtrl- MRL- AtnInd- PwrInd- HotPlug+
Surpise+
                Slot: Number 5, PowerLimit 6.500000
                Slot: Enabled AtnBtn- PwrFlt- MRL- PresDet+ CmdCplt- HPIrq-
                Slot: AttnInd Unknown, PwrInd Unknown, Power-
                Root: Correctable- Non-Fatal- Fatal- PME-
        Capabilities: [80] Message Signalled Interrupts: Mask- 64bit-
Queue=0/0 Enable+
                Address: fee0300c  Data: 41d9
        Capabilities: [90] Subsystem: Dell Unknown device [1028:01f2]
        Capabilities: [a0] Power Management version 2
                Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:1d.0 USB Controller [0c03]: Intel Corporation 82801H (ICH8 Family) USB
UHCI Controller #1 [8086:2830] (rev 02) (prog-if 00 [UHCI])
        Subsystem: Dell Unknown device [1028:01f2]
        Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
        Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
        Latency: 0
        Interrupt: pin A routed to IRQ 19
        Region 4: I/O ports at 6f80 [size=32]

00:1d.1 USB Controller [0c03]: Intel Corporation 82801H (ICH8 Family) USB
UHCI Controller #2 [8086:2831] (rev 02) (prog-if 00 [UHCI])
        Subsystem: Dell Unknown device [1028:01f2]
        Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
        Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
        Latency: 0
        Interrupt: pin B routed to IRQ 20
        Region 4: I/O ports at 6f60 [size=32]

00:1d.2 USB Controller [0c03]: Intel Corporation 82801H (ICH8 Family) USB
UHCI Controller #3 [8086:2832] (rev 02) (prog-if 00 [UHCI])
        Subsystem: Dell Unknown device [1028:01f2]
        Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
        Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
        Latency: 0
        Interrupt: pin C routed to IRQ 21
        Region 4: I/O ports at 6f40 [size=32]

00:1d.7 USB Controller [0c03]: Intel Corporation 82801H (ICH8 Family) USB2
EHCI Controller #1 [8086:2836] (rev 02) (prog-if 20 [EHCI])
        Subsystem: Dell Unknown device [1028:01f2]
        Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
        Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
        Latency: 0
        Interrupt: pin A routed to IRQ 19
        Region 0: Memory at fed1c000 (32-bit, non-prefetchable) [size=1K]
        Capabilities: [50] Power Management version 2
                Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-
        Capabilities: [58] Debug port

00:1e.0 PCI bridge [0604]: Intel Corporation 82801 Mobile PCI Bridge
[8086:2448] (rev f2) (prog-if 01 [Subtractive decode])
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
        Latency: 0
        Bus: primary=00, secondary=03, subordinate=03, sec-latency=32
        Memory behind bridge: f9b00000-f9bfffff
        Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ <SERR- <PERR-
        BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
        Capabilities: [50] Subsystem: Dell Unknown device [1028:01f2]

00:1f.0 ISA bridge [0601]: Intel Corporation 82801HEM (ICH8M) LPC Interface
Controller [8086:2815] (rev 02)
        Subsystem: Dell Unknown device [1028:01f2]
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
        Latency: 0
        Capabilities: [e0] Vendor Specific Information

00:1f.1 IDE interface [0101]: Intel Corporation 82801HBM/HEM (ICH8M/ICH8M-E)
IDE Controller [8086:2850] (rev 02) (prog-if 8a [Master SecP PriP])
        Subsystem: Dell Unknown device [1028:01f2]
        Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
        Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
        Latency: 0
        Interrupt: pin A routed to IRQ 16
        Region 0: I/O ports at 01f0 [size=8]
        Region 1: I/O ports at 03f4 [size=1]
        Region 2: I/O ports at 0170 [size=8]
        Region 3: I/O ports at 0374 [size=1]
        Region 4: I/O ports at 6fa0 [size=16]

00:1f.2 SATA controller [0106]: Intel Corporation 82801HBM/HEM
(ICH8M/ICH8M-E) SATA AHCI Controller [8086:2829] (rev 02) (prog-if 01 [AHCI
1.0])
        Subsystem: Dell Unknown device [1028:01f2]
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
        Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
        Latency: 0
        Interrupt: pin B routed to IRQ 219
        Region 0: I/O ports at 6eb0 [size=8]
        Region 1: I/O ports at 6eb8 [size=4]
        Region 2: I/O ports at 6ec0 [size=8]
        Region 3: I/O ports at 6ec8 [size=4]
        Region 4: I/O ports at 6ee0 [size=32]
        Region 5: Memory at febfb800 (32-bit, non-prefetchable) [size=2K]
        Capabilities: [80] Message Signalled Interrupts: Mask- 64bit-
Queue=0/2 Enable+
                Address: fee0300c  Data: 413a
        Capabilities: [70] Power Management version 3
                Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot+,D3cold-)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-
        Capabilities: [a8] #12 [0010]

00:1f.3 SMBus [0c05]: Intel Corporation 82801H (ICH8 Family) SMBus
Controller [8086:283e] (rev 02)
        Subsystem: Dell Unknown device [1028:01f2]
        Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
        Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
        Interrupt: pin B routed to IRQ 10
        Region 0: Memory at febfb700 (32-bit, non-prefetchable) [size=256]
        Region 4: I/O ports at 10c0 [size=32]

01:00.0 VGA compatible controller [0300]: nVidia Corporation GeForce 8400M
GS [10de:0427] (rev a1) (prog-if 00 [VGA])
        Subsystem: Dell Unknown device [1028:01f2]
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
        Latency: 0, Cache Line Size: 64 bytes
        Interrupt: pin A routed to IRQ 7
        Region 0: Memory at fd000000 (32-bit, non-prefetchable) [size=16M]
        Region 1: Memory at f4000000 (64-bit, prefetchable) [size=64M]
        Region 3: Memory at fa000000 (64-bit, non-prefetchable) [size=32M]
        Region 5: I/O ports at ef00 [size=128]
        Expansion ROM at fea00000 [disabled] [size=128K]
        Capabilities: [60] Power Management version 2
                Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-
        Capabilities: [68] Message Signalled Interrupts: Mask- 64bit+
Queue=0/0 Enable-
                Address: 0000000000000000  Data: 0000
        Capabilities: [78] Express Endpoint IRQ 0
                Device: Supported: MaxPayload 128 bytes, PhantFunc 0,
ExtTag+
                Device: Latency L0s <512ns, L1 <4us
                Device: AtnBtn- AtnInd- PwrInd-
                Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
                Device: RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
                Device: MaxPayload 128 bytes, MaxReadReq 512 bytes
                Link: Supported Speed 2.5Gb/s, Width x16, ASPM L0s L1, Port
0
                Link: Latency L0s <512ns, L1 <4us
                Link: ASPM L0s L1 Enabled RCB 128 bytes CommClk+ ExtSynch-
                Link: Speed 2.5Gb/s, Width x16

03:00.0 Ethernet controller [0200]: Broadcom Corporation BCM4401-B0
100Base-TX [14e4:170c] (rev 02)
        Subsystem: Dell Unknown device [1028:01f2]
        Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
        Latency: 64
        Interrupt: pin A routed to IRQ 17
        Region 0: Memory at f9bfe000 (32-bit, non-prefetchable) [size=8K]
        Capabilities: [40] Power Management version 2
                Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold+)
                Status: D0 PME-Enable- DSel=0 DScale=2 PME-

03:01.0 FireWire (IEEE 1394) [0c00]: Ricoh Co Ltd R5C832 IEEE 1394
Controller [1180:0832] (rev 05) (prog-if 10 [OHCI])
        Subsystem: Dell Unknown device [1028:01f2]
        Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
        Latency: 64 (500ns min, 1000ns max), Cache Line Size: 64 bytes
        Interrupt: pin A routed to IRQ 18
        Region 0: Memory at f9bfd800 (32-bit, non-prefetchable) [size=2K]
        Capabilities: [dc] Power Management version 2
                Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold+)
                Status: D0 PME-Enable- DSel=0 DScale=2 PME+

03:01.1 Generic system peripheral [0805]: Ricoh Co Ltd R5C822
SD/SDIO/MMC/MS/MSPro Host Adapter [1180:0822] (rev 22) (prog-if 01)
        Subsystem: Dell Unknown device [1028:01f2]
        Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
        Latency: 64, Cache Line Size: 64 bytes
        Interrupt: pin B routed to IRQ 22
        Region 0: Memory at f9bfd400 (32-bit, non-prefetchable) [size=256]
        Capabilities: [80] Power Management version 2
                Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold+)
                Status: D0 PME-Enable- DSel=0 DScale=2 PME-

03:01.2 System peripheral [0880]: Ricoh Co Ltd R5C843 MMC Host Controller
[1180:0843] (rev 12)
        Subsystem: Dell Unknown device [1028:01f2]
        Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
        Latency: 64, Cache Line Size: 64 bytes
        Interrupt: pin B routed to IRQ 4
        Region 0: Memory at f9bfd500 (32-bit, non-prefetchable) [size=256]
        Capabilities: [80] Power Management version 2
                Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold+)
                Status: D0 PME-Enable- DSel=0 DScale=2 PME-

03:01.3 System peripheral [0880]: Ricoh Co Ltd R5C592 Memory Stick Bus Host
Adapter [1180:0592] (rev 12)
        Subsystem: Dell Unknown device [1028:01f2]
        Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
        Latency: 64, Cache Line Size: 64 bytes
        Interrupt: pin B routed to IRQ 4
        Region 0: Memory at f9bfd600 (32-bit, non-prefetchable) [size=256]
        Capabilities: [80] Power Management version 2
                Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold+)
                Status: D0 PME-Enable- DSel=0 DScale=2 PME-

03:01.4 System peripheral [0880]: Ricoh Co Ltd xD-Picture Card Controller
[1180:0852] (rev 12)
        Subsystem: Dell Unknown device [1028:01f2]
        Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
        Latency: 64, Cache Line Size: 64 bytes
        Interrupt: pin B routed to IRQ 4
        Region 0: Memory at f9bfd700 (32-bit, non-prefetchable) [size=256]
        Capabilities: [80] Power Management version 2
                Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold+)
                Status: D0 PME-Enable- DSel=0 DScale=2 PME-

0c:00.0 Network controller [0280]: Intel Corporation PRO/Wireless 3945ABG
Network Connection [8086:4222] (rev 02)
        Subsystem: Intel Corporation Unknown device [8086:1020]
        Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
        Latency: 0, Cache Line Size: 64 bytes
        Interrupt: pin A routed to IRQ 17
        Region 0: Memory at f9fff000 (32-bit, non-prefetchable) [size=4K]
        Capabilities: [c8] Power Management version 2
                Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-
        Capabilities: [d0] Message Signalled Interrupts: Mask- 64bit+
Queue=0/0 Enable-
                Address: 0000000000000000  Data: 0000
        Capabilities: [e0] Express Legacy Endpoint IRQ 0
                Device: Supported: MaxPayload 128 bytes, PhantFunc 0,
ExtTag-
                Device: Latency L0s <512ns, L1 unlimited
                Device: AtnBtn- AtnInd- PwrInd-
                Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
                Device: RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
                Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
                Link: Supported Speed 2.5Gb/s, Width x1, ASPM L0s L1, Port 0
                Link: Latency L0s <128ns, L1 <64us
                Link: ASPM L1 Enabled RCB 64 bytes CommClk+ ExtSynch-
                Link: Speed 2.5Gb/s, Width x1

[EMAIL PROTECTED]:~$ uname -a
Linux ub-pc 2.6.22-12-generic #1 SMP Sun Sep 23 18:11:30 GMT 2007 i686
GNU/Linux


On 10/2/07, Brian Murray <[EMAIL PROTECTED]> wrote:
>
> Thanks for taking the time to report this bug and helping to make Ubuntu
> better.  It would be helpful if you could obtain the numeric PCI ID of
> the sound card.  You can get this via 'sudo lspci -vvnn'.  It would also
> be helpful to know the exact kernel version that you are running.  You
> can find this out via 'uname -a'.  Thanks in advance.
>
> ** Changed in: linux-source-2.6.22 (Ubuntu)
> Sourcepackagename: None => linux-source-2.6.22
>        Status: New => Incomplete
>
> ** Changed in: linux-source-2.6.22 (Ubuntu)
>    Importance: Undecided => Medium
>
> --
> no sound dell laptop 1720 gutsy beta
> https://bugs.launchpad.net/bugs/147899
> You received this bug notification because you are a direct subscriber
> of the bug.
>

-- 
no sound dell laptop 1720 gutsy beta
https://bugs.launchpad.net/bugs/147899
You received this bug notification because you are a member of Ubuntu
Bugs, which is the bug contact for Ubuntu.

-- 
ubuntu-bugs mailing list
ubuntu-bugs@lists.ubuntu.com
https://lists.ubuntu.com/mailman/listinfo/ubuntu-bugs

Reply via email to