To follow up on the problem mentioned with 3.6-rc7 kernel # wpa_supplicant -d -Dnl80211,wext -ieth2 -u -s -O /var/run/wpa_supplicant
Syslog (masked MAC addrs, uuid, bssids, etc.) wpa_supplicant: Initializing interface 'eth2' conf 'N/A' driver 'nl80211,wext' ctrl_interface '/var/run/wpa_supplicant' bridge 'N/A' wpa_supplicant: Could not open file /sys/class/net/eth2/phy80211/name: No such file or directory wpa_supplicant: rfkill: initial event: idx=0 type=1 op=0 soft=0 hard=0 wpa_supplicant: rfkill: initial event: idx=1 type=2 op=0 soft=1 hard=0 wpa_supplicant: rfkill: initial event: idx=2 type=2 op=0 soft=1 hard=0 wpa_supplicant: nl80211: Set mode ifindex 5 iftype 2 (STATION) wpa_supplicant: nl80211: Failed to set interface 5 to mode 2: -19 (No such device) wpa_supplicant: nl80211: Try mode change after setting interface down wpa_supplicant: nl80211: Set mode ifindex 5 iftype 2 (STATION) wpa_supplicant: nl80211: Failed to set interface 5 to mode 2: -19 (No such device) wpa_supplicant: nl80211: Interface mode change to 2 from 0 failed wpa_supplicant: nl80211: Could not configure driver to use managed mode wpa_supplicant: netlink: Operstate: linkmode=0, operstate=6 wpa_supplicant: nl80211: Set mode ifindex 5 iftype 2 (STATION) wpa_supplicant: nl80211: Failed to set interface 5 to mode 2: -19 (No such device) wpa_supplicant: nl80211: Try mode change after setting interface down wpa_supplicant: nl80211: Set mode ifindex 5 iftype 2 (STATION) wpa_supplicant: nl80211: Failed to set interface 5 to mode 2: -19 (No such device) wpa_supplicant: nl80211: Interface mode change to 2 from 0 failed wpa_supplicant: eth2: Failed to initialize driver interface - try next driver wrapper wpa_supplicant: rfkill: initial event: idx=0 type=1 op=0 soft=0 hard=0 wpa_supplicant: rfkill: initial event: idx=1 type=2 op=0 soft=1 hard=0 wpa_supplicant: rfkill: initial event: idx=2 type=2 op=0 soft=1 hard=0 wpa_supplicant: SIOCGIWRANGE: WE(compiled)=22 WE(source)=19 enc_capa=0xf wpa_supplicant: capabilities: key_mgmt 0xf enc 0xf flags 0x0 wpa_supplicant: netlink: Operstate: linkmode=1, operstate=5 wpa_supplicant: eth2: Own MAC address: xx:xx:xx:xx:xx:xx wpa_supplicant: wpa_driver_wext_set_key: alg=0 key_idx=0 set_tx=0 seq_len=0 key_len=0 wpa_supplicant: wpa_driver_wext_set_key: alg=0 key_idx=1 set_tx=0 seq_len=0 key_len=0 wpa_supplicant: wpa_driver_wext_set_key: alg=0 key_idx=2 set_tx=0 seq_len=0 key_len=0 wpa_supplicant: wpa_driver_wext_set_key: alg=0 key_idx=3 set_tx=0 seq_len=0 key_len=0 wpa_supplicant: wpa_driver_wext_set_key: alg=0 key_idx=4 set_tx=0 seq_len=0 key_len=0 wpa_supplicant: wpa_driver_wext_set_key: alg=0 key_idx=5 set_tx=0 seq_len=0 key_len=0 wpa_supplicant: wpa_driver_wext_set_countermeasures wpa_supplicant: eth2: RSN: flushing PMKID list in the driver wpa_supplicant: eth2: State: DISCONNECTED -> INACTIVE wpa_supplicant: WPS: Set UUID for interface eth2 wpa_supplicant: WPS: UUID based on MAC address - hexdump(len=16): xx xx xx xx xx xx xx xx xx xx xx xx xx xx xx xx wpa_supplicant: EAPOL: SUPP_PAE entering state DISCONNECTED wpa_supplicant: EAPOL: Supplicant port status: Unauthorized wpa_supplicant: EAPOL: KEY_RX entering state NO_KEY_RECEIVE wpa_supplicant: EAPOL: SUPP_BE entering state INITIALIZE wpa_supplicant: EAP: EAP entering state DISABLED wpa_supplicant: EAPOL: Supplicant port status: Unauthorized wpa_supplicant: EAPOL: Supplicant port status: Unauthorized wpa_supplicant: dbus: Register interface object '/fi/w1/wpa_supplicant1/Interfaces/7' wpa_supplicant: eth2: Added interface eth2 wpa_supplicant: nl80211: Ignore event for foreign ifindex 5 wpa_supplicant: nl80211: Ignore event for foreign ifindex 5 wpa_supplicant: nl80211: Ignore event for foreign ifindex 5 wpa_supplicant: nl80211: Ignore event for foreign ifindex 5 wpa_supplicant: nl80211: Ignore event for foreign ifindex 5 wpa_supplicant: nl80211: Ignore event for foreign ifindex 5 wpa_supplicant: nl80211: Ignore event for foreign ifindex 5 wpa_supplicant: RTM_NEWLINK: operstate=0 ifi_flags=0x11043 ([UP][RUNNING][LOWER_UP]) wpa_supplicant: RTM_NEWLINK, IFLA_IFNAME: Interface 'eth2' added wpa_supplicant: WEXT: if_removed already cleared - ignore event wpa_supplicant: Wireless event: cmd=0x8b06 len=12 wpa_supplicant: RTM_NEWLINK: operstate=0 ifi_flags=0x11043 ([UP][RUNNING][LOWER_UP]) wpa_supplicant: RTM_NEWLINK, IFLA_IFNAME: Interface 'eth2' added wpa_supplicant: WEXT: if_removed already cleared - ignore event wpa_supplicant: Wireless event: cmd=0x8b1a len=48 wpa_supplicant: RTM_NEWLINK: operstate=0 ifi_flags=0x11003 ([UP][LOWER_UP]) wpa_supplicant: RTM_NEWLINK, IFLA_IFNAME: Interface 'eth2' added wpa_supplicant: WEXT: if_removed already cleared - ignore event NetworkManager: <info> (eth2): supplicant interface state: starting -> ready NetworkManager: <info> (eth2): device state change: unavailable -> disconnected (reason 'supplicant-available') [20 30 42] wpa_supplicant: Scan requested (ret=0) - scan timeout 10 seconds NetworkManager: <info> (eth2): supplicant interface state: ready -> inactive NetworkManager: <warn> Trying to remove a non-existant call id. wpa_supplicant: nl80211: Ignore event for foreign ifindex 5 wpa_supplicant: RTM_NEWLINK: operstate=0 ifi_flags=0x11003 ([UP][LOWER_UP]) wpa_supplicant: RTM_NEWLINK, IFLA_IFNAME: Interface 'eth2' added wpa_supplicant: WEXT: if_removed already cleared - ignore event wpa_supplicant: Wireless event: cmd=0x8c02 len=37 wpa_supplicant: Scan requested (ret=0) - scan timeout 10 seconds wpa_supplicant: EAPOL: disable timer tick wpa_supplicant: EAPOL: Supplicant port status: Unauthorized wpa_supplicant: nl80211: Ignore event for foreign ifindex 5 wpa_supplicant: RTM_NEWLINK: operstate=0 ifi_flags=0x11003 ([UP][LOWER_UP]) wpa_supplicant: RTM_NEWLINK, IFLA_IFNAME: Interface 'eth2' added wpa_supplicant: WEXT: if_removed already cleared - ignore event wpa_supplicant: Wireless event: cmd=0x8b19 len=16 wpa_supplicant: eth2: Event SCAN_RESULTS (3) received wpa_supplicant: Received 3282 bytes of scan results (12 BSSes) wpa_supplicant: eth2: BSS: Start scan result update 1 wpa_supplicant: eth2: BSS: Add new id 0 BSSID xx:xx:xx:xx:xx:xx SSID 'MySSID' wpa_supplicant: dbus: Register BSS object '/fi/w1/wpa_supplicant1/Interfaces/7/BSSs/0' [..snip..] [ 9 other AP's scanned ] [..snip..] wpa_supplicant: eth2: BSS: Add new id 11 BSSID xx:xx:xx:xx:xx:xx SSID 'Neighbors' wpa_supplicant: dbus: Register BSS object '/fi/w1/wpa_supplicant1/Interfaces/7/BSSs/11' NetworkManager: <info> Activation (eth2) starting connection 'MySSID' NetworkManager: <info> (eth2): device state change: disconnected -> prepare (reason 'none') [30 40 0] wpa_supplicant: eth2: New scan results available wpa_supplicant: eth2: No suitable network found wpa_supplicant: eth2: State: INACTIVE -> INACTIVE NetworkManager: <info> Activation (eth2) Stage 1 of 5 (Device Prepare) scheduled... wpa_supplicant: dbus: flush_object_timeout_handler: Timeout - sending changed properties of object /fi/w1/wpa_supplicant1/Interfaces/7 NetworkManager: <info> Activation (eth2) Stage 1 of 5 (Device Prepare) started... NetworkManager: <info> Activation (eth2) Stage 2 of 5 (Device Configure) scheduled... NetworkManager: <info> Activation (eth2) Stage 1 of 5 (Device Prepare) complete. NetworkManager: <info> Activation (eth2) Stage 2 of 5 (Device Configure) starting... NetworkManager: <info> (eth2): device state change: prepare -> config (reason 'none') [40 50 0] NetworkManager: <info> Activation (eth2/wireless): connection 'MySSID' has security, and secrets exist. No new secrets needed. NetworkManager: <info> Config: added 'ssid' value 'MySSID' NetworkManager: <info> Config: added 'scan_ssid' value '1' NetworkManager: <info> Config: added 'key_mgmt' value 'WPA-PSK' NetworkManager: <info> Config: added 'auth_alg' value 'OPEN' NetworkManager: <info> Config: added 'psk' value '<omitted>' NetworkManager: <info> Activation (eth2) Stage 2 of 5 (Device Configure) complete. NetworkManager: <info> Config: set interface ap_scan to 1 wpa_supplicant: dbus: Register network object '/fi/w1/wpa_supplicant1/Interfaces/7/Networks/0' wpa_supplicant: eth2: Setting scan request: 0 sec 0 usec wpa_supplicant: eth2: State: INACTIVE -> SCANNING wpa_supplicant: eth2: Starting AP scan for specific SSID(s) wpa_supplicant: Scan requested (ret=0) - scan timeout 30 seconds wpa_supplicant: dbus: flush_object_timeout_handler: Timeout - sending changed properties of object /fi/w1/wpa_supplicant1/Interfaces/7 NetworkManager: <info> (eth2): supplicant interface state: inactive -> scanning wpa_supplicant: nl80211: Ignore event for foreign ifindex 2 wpa_supplicant: Ignore event for foreign ifindex 2 wpa_supplicant: nl80211: Ignore event for foreign ifindex 5 wpa_supplicant: RTM_NEWLINK: operstate=0 ifi_flags=0x11003 ([UP][LOWER_UP]) wpa_supplicant: RTM_NEWLINK, IFLA_IFNAME: Interface 'eth2' added wpa_supplicant: WEXT: if_removed already cleared - ignore event wpa_supplicant: Wireless event: cmd=0x8b19 len=16 wpa_supplicant: eth2: Event SCAN_RESULTS (3) received wpa_supplicant: Received 249 bytes of scan results (1 BSSes) wpa_supplicant: eth2: BSS: Start scan result update 2 wpa_supplicant: eth2: New scan results available wpa_supplicant: eth2: Selecting BSS from priority group 0 wpa_supplicant: eth2: 0: xx:xx:xx:xx:xx:xx ssid='MySSID' wpa_ie_len=0 rsn_ie_len=24 caps=0x11 level=-62 wpa_supplicant: eth2: selected based on RSN IE wpa_supplicant: eth2: selected BSS xx:xx:xx:xx:xx:xx ssid='MySSID' wpa_supplicant: eth2: Request association: reassociate: 1 selected: xx:xx:xx:xx:xx:xx bssid: 00:00:00:00:00:00 pending: 00:00:00:00:00:00 wpa_state: SCANNING wpa_supplicant: eth2: Trying to associate with xx:xx:xx:xx:xx:xx (SSID='MySSID' freq=2452 MHz) wpa_supplicant: FT: Stored MDIE and FTIE from (Re)Association Response - hexdump(len=0): wpa_supplicant: eth2: Cancelling scan request wpa_supplicant: eth2: WPA: clearing own WPA/RSN IE wpa_supplicant: eth2: Automatic auth_alg selection: 0x1 wpa_supplicant: eth2: Overriding auth_alg selection: 0x1 wpa_supplicant: eth2: RSN: using IEEE 802.11i/D9.0 wpa_supplicant: eth2: WPA: Selected cipher suites: group 8 pairwise 24 key_mgmt 2 proto 2 wpa_supplicant: eth2: WPA: clearing AP WPA IE wpa_supplicant: WPA: set AP RSN IE - hexdump(len=26): xx xx xx xx xx xx xx xx xx xx xx [..snip..] wpa_supplicant: eth2: WPA: using GTK TKIP wpa_supplicant: eth2: WPA: using PTK CCMP wpa_supplicant: eth2: WPA: using KEY_MGMT WPA-PSK wpa_supplicant: eth2: WPA: not using MGMT group cipher wpa_supplicant: WPA: Set own WPA IE default - hexdump(len=22): xx xx xx xx xx xx xx xx xx xx xx [..snip..] wpa_supplicant: eth2: No keys have been configured - skip key clearing wpa_supplicant: eth2: State: SCANNING -> ASSOCIATING wpa_supplicant: wpa_driver_wext_set_operstate: operstate 0->0 (DORMANT) wpa_supplicant: netlink: Operstate: linkmode=-1, operstate=5 wpa_supplicant: wpa_driver_wext_associate wpa_supplicant: wpa_driver_wext_set_drop_unencrypted wpa_supplicant: wpa_driver_wext_set_psk wpa_supplicant: eth2: Association request to the driver failed wpa_supplicant: eth2: Setting authentication timeout: 5 sec 0 usec wpa_supplicant: EAPOL: External notification - EAP success=0 wpa_supplicant: EAPOL: Supplicant port status: Unauthorized wpa_supplicant: EAPOL: External notification - EAP fail=0 wpa_supplicant: EAPOL: Supplicant port status: Unauthorized wpa_supplicant: EAPOL: External notification - portControl=Auto wpa_supplicant: EAPOL: Supplicant port status: Unauthorized wpa_supplicant: RSN: Ignored PMKID candidate without preauth flag wpa_supplicant: RTM_NEWLINK: operstate=0 ifi_flags=0x11003 ([UP][LOWER_UP]) wpa_supplicant: RTM_NEWLINK, IFLA_IFNAME: Interface 'eth2' added wpa_supplicant: WEXT: if_removed already cleared - ignore event wpa_supplicant: Wireless event: cmd=0x8b06 len=12 wpa_supplicant: RTM_NEWLINK: operstate=0 ifi_flags=0x11003 ([UP][LOWER_UP]) wpa_supplicant: RTM_NEWLINK, IFLA_IFNAME: Interface 'eth2' added wpa_supplicant: WEXT: if_removed already cleared - ignore event wpa_supplicant: Wireless event: cmd=0x8b04 len=16 wpa_supplicant: RTM_NEWLINK: operstate=0 ifi_flags=0x11003 ([UP][LOWER_UP]) wpa_supplicant: RTM_NEWLINK, IFLA_IFNAME: Interface 'eth2' added wpa_supplicant: WEXT: if_removed already cleared - ignore event wpa_supplicant: Wireless event: cmd=0x8b1a len=23 wpa_supplicant: nl80211: Ignore event for foreign ifindex 5 wpa_supplicant: nl80211: Ignore event for foreign ifindex 5 wpa_supplicant: nl80211: Ignore event for foreign ifindex 5 wpa_supplicant: dbus: flush_object_timeout_handler: Timeout - sending changed properties of object /fi/w1/wpa_supplicant1/Interfaces/7 wpa_supplicant: dbus: flush_object_timeout_handler: Timeout - sending changed properties of object /fi/w1/wpa_supplicant1/Interfaces/7/BSSs/0 NetworkManager: <info> (eth2): supplicant interface state: scanning -> associating wpa_supplicant: nl80211: Ignore event for foreign ifindex 5 wpa_supplicant: nl80211: Ignore event for foreign ifindex 5 wpa_supplicant: RTM_NEWLINK: operstate=0 ifi_flags=0x11003 ([UP][LOWER_UP]) wpa_supplicant: RTM_NEWLINK, IFLA_IFNAME: Interface 'eth2' added wpa_supplicant: WEXT: if_removed already cleared - ignore event wpa_supplicant: Wireless event: cmd=0x8c02 len=41 wpa_supplicant: RTM_NEWLINK: operstate=0 ifi_flags=0x11003 ([UP][LOWER_UP]) wpa_supplicant: RTM_NEWLINK, IFLA_IFNAME: Interface 'eth2' added wpa_supplicant: WEXT: if_removed already cleared - ignore event wpa_supplicant: Wireless event: cmd=0x8c02 len=41 wpa_supplicant: eth2: Authentication with xx:xx:xx:xx:xx:xx timed out. wpa_supplicant: Added BSSID xx:xx:xx:xx:xx:xx into blacklist wpa_supplicant: eth2: No keys have been configured - skip key clearing wpa_supplicant: eth2: State: ASSOCIATING -> DISCONNECTED wpa_supplicant: wpa_driver_wext_set_operstate: operstate 0->0 (DORMANT) wpa_supplicant: netlink: Operstate: linkmode=-1, operstate=5 wpa_supplicant: EAPOL: External notification - portEnabled=0 wpa_supplicant: EAPOL: Supplicant port status: Unauthorized wpa_supplicant: EAPOL: External notification - portValid=0 wpa_supplicant: EAPOL: Supplicant port status: Unauthorized wpa_supplicant: EAPOL: External notification - EAP success=0 wpa_supplicant: EAPOL: Supplicant port status: Unauthorized wpa_supplicant: eth2: Setting scan request: 1 sec 0 usec wpa_supplicant: dbus: flush_object_timeout_handler: Timeout - sending changed properties of object /fi/w1/wpa_supplicant1/Interfaces/7 NetworkManager: <info> (eth2): supplicant interface state: associating -> disconnected -- You received this bug notification because you are a member of Ubuntu Bugs, which is subscribed to Ubuntu. https://bugs.launchpad.net/bugs/923809 Title: Upgrade bcmwl to verison 6.20.55.19 (r300276) or greater To manage notifications about this bug go to: https://bugs.launchpad.net/ubuntu/+source/bcmwl/+bug/923809/+subscriptions -- ubuntu-bugs mailing list ubuntu-bugs@lists.ubuntu.com https://lists.ubuntu.com/mailman/listinfo/ubuntu-bugs
