Sigh. System never gets that far:
System is a Compaq Armada with a Pentium III 500Mhz MMC-2 module
installed. System has 327Mb of main memory. It has a 2Mb ATI Rage video
system.
It boots fine into this kernel: uname -a
Linux bisohlinuxp1 2.6.20-13-server #2 SMP Sun Mar 25 00:26:22 UTC 2007 i686
GNU/Linux
This is the output of lspci -vvnn :
00:00.0 Host bridge [0600]: Intel Corporation 440BX/ZX/DX - 82443BX/ZX/DX Host
bridge [8086:7190] (rev 03)
Subsystem: Compaq Computer Corporation Armada 1750 Laptop System
Chipset [0e11:0500]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ >SERR- <PERR-
Latency: 64
Region 0: Memory at 44000000 (32-bit, prefetchable) [size=64M]
Capabilities: [a0] AGP version 1.0
Status: RQ=32 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans-
64bit- FW- AGP3- Rate=x2
Command: RQ=1 ArqSz=0 Cal=0 SBA+ AGP+ GART64- 64bit- FW- Rate=x2
00:01.0 PCI bridge [0604]: Intel Corporation 440BX/ZX/DX - 82443BX/ZX/DX AGP
bridge [8086:7191] (rev 03) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 00001000-00001fff
Memory behind bridge: 40000000-410fffff
Prefetchable memory behind bridge: 30000000-300fffff
Secondary status: 66MHz+ FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA+ MAbort- >Reset- FastB2B+
00:07.0 ISA bridge [0601]: Intel Corporation 82371AB/EB/MB PIIX4 ISA
[8086:7110] (rev 02)
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
00:07.1 IDE interface [0101]: Intel Corporation 82371AB/EB/MB PIIX4 IDE
[8086:7111] (rev 01) (prog-if 80 [Master])
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64
Region 0: [virtual] Memory at 000001f0 (32-bit, non-prefetchable)
[disabled] [size=8]
Region 1: [virtual] Memory at 000003f0 (type 3, non-prefetchable)
[disabled] [size=1]
Region 2: [virtual] Memory at 00000170 (32-bit, non-prefetchable)
[disabled] [size=8]
Region 3: [virtual] Memory at 00000370 (type 3, non-prefetchable)
[disabled] [size=1]
Region 4: I/O ports at 2020 [size=16]
00:07.2 USB Controller [0c03]: Intel Corporation 82371AB/EB/MB PIIX4 USB
[8086:7112] (rev 01) (prog-if 00 [UHCI])
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64
Interrupt: pin D routed to IRQ 11
Region 4: I/O ports at 2000 [size=32]
00:07.3 Bridge [0680]: Intel Corporation 82371AB/EB/MB PIIX4 ACPI [8086:7113]
(rev 02)
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin ? routed to IRQ 9
00:11.0 CardBus bridge [0607]: Texas Instruments PCI1225 [104c:ac1c] (rev 01)
Subsystem: Compaq Computer Corporation Armada E500 [0e11:b121]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 168, Cache Line Size: 128 bytes
Interrupt: pin A routed to IRQ 11
Region 0: Memory at 7fffe000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=00, secondary=02, subordinate=05, sec-latency=176
Memory window 0: 20000000-23fff000 (prefetchable)
Memory window 1: 24000000-27fff000
I/O window 0: 00002400-000024ff
I/O window 1: 00002800-000028ff
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset- 16bInt- PostWrite+
16-bit legacy interface ports at 0001
00:11.1 CardBus bridge [0607]: Texas Instruments PCI1225 [104c:ac1c] (rev 01)
Subsystem: Compaq Computer Corporation Armada E500 [0e11:b121]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 168, Cache Line Size: 128 bytes
Interrupt: pin A routed to IRQ 11
Region 0: Memory at 7ffff000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=00, secondary=06, subordinate=09, sec-latency=176
Memory window 0: 28000000-2bfff000 (prefetchable)
Memory window 1: 2c000000-2ffff000
I/O window 0: 00002c00-00002cff
I/O window 1: 00003000-000030ff
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset+ 16bInt+ PostWrite+
16-bit legacy interface ports at 0001
01:00.0 VGA compatible controller [0300]: ATI Technologies Inc 3D Rage LT Pro
AGP-133 [1002:4c42] (rev dc) (prog-if 00 [VGA])
Subsystem: Compaq Computer Corporation 3D Rage LT Pro (Compaq Armada
1750) [0e11:b10e]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping+ SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 66 (2000ns min), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 11
Region 0: Memory at 40000000 (32-bit, non-prefetchable) [size=16M]
Region 1: I/O ports at 1000 [size=256]
Region 2: Memory at 41000000 (32-bit, non-prefetchable) [size=4K]
[virtual] Expansion ROM at 30000000 [disabled] [size=128K]
Capabilities: [50] AGP version 1.0
Status: RQ=256 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans-
64bit- FW- AGP3- Rate=x1,x2
Command: RQ=1 ArqSz=0 Cal=0 SBA+ AGP+ GART64- 64bit- FW- Rate=x2
Capabilities: [5c] Power Management version 1
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
02:00.0 Ethernet controller [0200]: Xircom Cardbus Ethernet 10/100 [115d:0003]
(rev 03)
Subsystem: Xircom Cardbus Ethernet 10/100 [115d:0181]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (5000ns min, 10000ns max)
Interrupt: pin A routed to IRQ 11
Region 0: I/O ports at 2400 [size=128]
Region 1: Memory at 24000000 (32-bit, non-prefetchable) [size=2K]
Region 2: Memory at 24000800 (32-bit, non-prefetchable) [size=2K]
[virtual] Expansion ROM at 20000000 [disabled] [size=16K]
Capabilities: [dc] Power Management version 1
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=2 PME-
[ 0.000000] Linux version 2.6.20-13-server ([EMAIL PROTECTED]) (gcc version
4.1.2 (Ubuntu 4.1.2-0ubuntu4)) #2 SMP Sun Mar 25 00:26:22 UTC 2007 (Ubuntu
2.6.20-13.21-server)
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] sanitize start
[ 0.000000] sanitize end
[ 0.000000] copy_e820_map() start: 0000000000000000 size: 000000000009fc00
end: 000000000009fc00 type: 1
[ 0.000000] copy_e820_map() type is E820_RAM
[ 0.000000] copy_e820_map() start: 000000000009fc00 size: 0000000000000400
end: 00000000000a0000 type: 2
[ 0.000000] copy_e820_map() start: 00000000000f0000 size: 0000000000010000
end: 0000000000100000 type: 2
[ 0.000000] copy_e820_map() start: 0000000000100000 size: 0000000013ef8000
end: 0000000013ff8000 type: 1
[ 0.000000] copy_e820_map() type is E820_RAM
[ 0.000000] copy_e820_map() start: 0000000013ff8000 size: 0000000000008000
end: 0000000014000000 type: 4
[ 0.000000] BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
[ 0.000000] BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
[ 0.000000] BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
[ 0.000000] BIOS-e820: 0000000000100000 - 0000000013ff8000 (usable)
[ 0.000000] BIOS-e820: 0000000013ff8000 - 0000000014000000 (ACPI NVS)
[ 0.000000] 0MB HIGHMEM available.
[ 0.000000] 319MB LOWMEM available.
[ 0.000000] Entering add_active_range(0, 0, 81912) 0 entries of 256 used
[ 0.000000] Zone PFN ranges:
[ 0.000000] DMA 0 -> 4096
[ 0.000000] Normal 4096 -> 81912
[ 0.000000] HighMem 81912 -> 81912
[ 0.000000] early_node_map[1] active PFN ranges
[ 0.000000] 0: 0 -> 81912
[ 0.000000] On node 0 totalpages: 81912
[ 0.000000] DMA zone: 32 pages used for memmap
[ 0.000000] DMA zone: 0 pages reserved
[ 0.000000] DMA zone: 4064 pages, LIFO batch:0
[ 0.000000] Normal zone: 607 pages used for memmap
[ 0.000000] Normal zone: 77209 pages, LIFO batch:15
[ 0.000000] HighMem zone: 0 pages used for memmap
[ 0.000000] DMI not present or invalid.
[ 0.000000] ACPI: RSDP (v000 COMPAQ ) @
0x000fb2a0
[ 0.000000] ACPI: RSDT (v001 COMPAQ RSDTBL 0x00000001 CPQ 0x00000001) @
0x13ff8000
[ 0.000000] ACPI: FADT (v001 COMPAQ CPQB142 0x19991130 CPQ 0x00000001) @
0x13ff8028
[ 0.000000] ACPI: DSDT (v001 COMPAQ ARMADA17 0x00010000 MSFT 0x0100000a) @
0x00000000
[ 0.000000] ACPI: Disabling ACPI support
[ 0.000000] Allocating PCI resources starting at 20000000 (gap:
14000000:ec000000)
[ 0.000000] Detected 497.577 MHz processor.
[ 1411.590812] Built 1 zonelists. Total pages: 81273
[ 1411.590826] Kernel command line:
root=UUID=0914e7ca-ea52-491e-ad1f-f1d639632c2e ro quiet splash
[ 1411.591602] Local APIC disabled by BIOS -- you can enable it with "lapic"
[ 1411.591633] mapped APIC to ffffd000 (0128a000)
[ 1411.591647] Enabling fast FPU save and restore... done.
[ 1411.591658] Enabling unmasked SIMD FPU exception support... done.
[ 1411.591688] Initializing CPU#0
[ 1411.591813] PID hash table entries: 2048 (order: 11, 8192 bytes)
[ 1411.593372] Console: colour VGA+ 80x25
[ 1411.594615] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 1411.596671] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 1411.636027] Memory: 313628k/327648k available (2020k kernel code, 13448k
reserved, 893k data, 328k init, 0k highmem)
[ 1411.636071] virtual kernel memory layout:
[ 1411.636077] fixmap : 0xfff4f000 - 0xfffff000 ( 704 kB)
[ 1411.636083] pkmap : 0xffc00000 - 0xffe00000 (2048 kB)
[ 1411.636089] vmalloc : 0xd4800000 - 0xffbfe000 ( 691 MB)
[ 1411.636096] lowmem : 0xc0000000 - 0xd3ff8000 ( 319 MB)
[ 1411.636102] .init : 0xc03df000 - 0xc0431000 ( 328 kB)
[ 1411.636108] .data : 0xc02f9004 - 0xc03d8754 ( 893 kB)
[ 1411.636115] .text : 0xc0100000 - 0xc02f9004 (2020 kB)
[ 1411.636129] Checking if this processor honours the WP bit even in supervisor
mode... Ok.
[ 1411.781726] Calibrating delay using timer specific routine.. 996.07 BogoMIPS
(lpj=4980392)
[ 1411.781934] Security Framework v1.0.0 initialized
[ 1411.781973] SELinux: Disabled at boot.
[ 1411.782057] Mount-cache hash table entries: 512
[ 1411.782698] CPU: After generic identify, caps: 0383f9ff 00000000 00000000
00000000 00000000 00000000 00000000
[ 1411.782747] CPU: L1 I cache: 16K, L1 D cache: 16K
[ 1411.782763] CPU: After all inits, caps: 0383f9ff 00000000 00000000 00000040
00000000 00000000 00000000
[ 1411.782818] Compat vDSO mapped to ffffe000.
[ 1411.782847] Remapping vsyscall page to ffffe000
[ 1411.782885] Checking 'hlt' instruction... OK.
[ 1411.822026] SMP alternatives: switching to UP code
[ 1411.822632] Freeing SMP alternatives: 11k freed
[ 1411.823351] Early unpacking initramfs... done
[ 1413.315673] CPU0: Intel Pentium III (Coppermine) stepping 03
[ 1413.315699] SMP motherboard not detected.
[ 1413.315709] Local APIC not detected. Using dummy APIC emulation.
[ 1413.315967] Brought up 1 CPUs
[ 1413.316975] Booting paravirtualized kernel on bare hardware
[ 1413.317270] Time: 15:07:41 Date: 03/09/107
[ 1413.317410] NET: Registered protocol family 16
[ 1413.317927] EISA bus registered
[ 1413.348296] PCI: PCI BIOS revision 2.10 entry at 0xf0484, last bus=1
[ 1413.348310] PCI: Using configuration type 1
[ 1413.348319] Setting up standard PCI resources
[ 1413.355117] ACPI: Interpreter disabled.
[ 1413.355139] Linux Plug and Play Support v0.97 (c) Adam Belay
[ 1413.355176] pnp: PnP ACPI: disabled
[ 1413.355187] PnPBIOS: Scanning system for PnP BIOS support...
[ 1413.355627] PnPBIOS: Found PnP BIOS installation structure at 0xc00fe2d0
[ 1413.355642] PnPBIOS: PnP BIOS version 1.0, entry 0xf0000:0x4d38, dseg 0xf0000
[ 1413.363456] PnPBIOS: 19 nodes reported by PnP BIOS; 19 recorded by driver
[ 1413.363811] PCI: Probing PCI hardware
[ 1413.363833] PCI: Probing PCI hardware (bus 00)
[ 1413.364488] * Found PM-Timer Bug on the chipset. Due to workarounds for a
bug,
[ 1413.364498] * this clock source is slow. Consider trying other clock sources
[ 1413.364568] PCI quirk: region 0f00-0f3f claimed by PIIX4 ACPI
[ 1413.364581] PCI quirk: region 0d00-0d0f claimed by PIIX4 SMB
[ 1413.365136] Boot video device is 0000:01:00.0
[ 1413.369264] PCI: Using IRQ router PIIX/ICH [8086/7110] at 0000:00:07.0
[ 1413.389745] NET: Registered protocol family 8
[ 1413.389760] NET: Registered protocol family 20
[ 1413.389819] NetLabel: Initializing
[ 1413.389829] NetLabel: domain hash size = 128
[ 1413.389837] NetLabel: protocols = UNLABELED CIPSOv4
[ 1413.389897] NetLabel: unlabeled traffic allowed by default
[ 1413.393420] PCI: Bridge: 0000:00:01.0
[ 1413.393439] IO window: 1000-1fff
[ 1413.393453] MEM window: 40000000-410fffff
[ 1413.393465] PREFETCH window: 30000000-300fffff
[ 1413.393479] PCI: Bus 2, cardbus bridge: 0000:00:11.0
[ 1413.393489] IO window: 00002400-000024ff
[ 1413.393500] IO window: 00002800-000028ff
[ 1413.393512] PREFETCH window: 20000000-23ffffff
[ 1413.393524] MEM window: 24000000-27ffffff
[ 1413.393535] PCI: Bus 6, cardbus bridge: 0000:00:11.1
[ 1413.393544] IO window: 00002c00-00002cff
[ 1413.393555] IO window: 00003000-000030ff
[ 1413.393567] PREFETCH window: 28000000-2bffffff
[ 1413.393578] MEM window: 2c000000-2fffffff
[ 1413.393623] PCI: setting IRQ 11 as level-triggered
[ 1413.393634] PCI: Found IRQ 11 for device 0000:00:11.0
[ 1413.393662] PCI: Sharing IRQ 11 with 0000:00:11.1
[ 1413.393676] PCI: Sharing IRQ 11 with 0000:01:00.0
[ 1413.393707] PCI: Found IRQ 11 for device 0000:00:11.1
[ 1413.393732] PCI: Sharing IRQ 11 with 0000:00:11.0
[ 1413.393746] PCI: Sharing IRQ 11 with 0000:01:00.0
[ 1413.393856] NET: Registered protocol family 2
[ 1413.491227] IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 1413.491682] TCP established hash table entries: 16384 (order: 5, 131072
bytes)
[ 1413.492367] TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
[ 1413.492723] TCP: Hash tables configured (established 16384 bind 8192)
[ 1413.492736] TCP reno registered
[ 1413.521348] checking if image is initramfs... it is
[ 1416.314964] Freeing initrd memory: 6759k freed
[ 1416.317086] audit: initializing netlink socket (disabled)
[ 1416.317134] audit(1176131265.680:1): initialized
[ 1416.317849] VFS: Disk quotas dquot_6.5.1
[ 1416.317949] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 1416.318231] io scheduler noop registered
[ 1416.318250] io scheduler anticipatory registered
[ 1416.318260] io scheduler deadline registered (default)
[ 1416.318334] io scheduler cfq registered
[ 1416.318363] Limiting direct PCI/PCI transfers.
[ 1416.319367] isapnp: Scanning for PnP cards...
[ 1416.676450] isapnp: No Plug & Play device found
[ 1416.976588] Real Time Clock Driver v1.12ac
[ 1416.977198] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing
enabled
[ 1416.977626] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 1416.979375] serial8250: ttyS2 at I/O 0x3e8 (irq = 4) is a 16550A
[ 1416.982036] 00:02: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 1416.984483] mice: PS/2 mouse device common for all mice
[ 1416.990023] RAMDISK driver initialized: 16 RAM disks of 65536K size 1024
blocksize
[ 1416.991307] input: Macintosh mouse button emulation as /class/input/input0
[ 1416.991622] Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
[ 1416.991646] ide: Assuming 33MHz system bus speed for PIO modes; override
with idebus=xx
[ 1416.992668] PNP: PS/2 Controller [PNP0303,PNP0f0e] at 0x60,0x64 irq 1,12
[ 1416.999592] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 1416.999622] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 1417.000594] EISA: Probing bus 0 at eisa.0
[ 1417.000625] Cannot allocate resource for EISA slot 1
[ 1417.000636] Cannot allocate resource for EISA slot 2
[ 1417.000647] Cannot allocate resource for EISA slot 3
[ 1417.000706] EISA: Detected 0 cards.
[ 1417.001053] TCP cubic registered
[ 1417.001105] NET: Registered protocol family 1
[ 1417.001217] Using IPI No-Shortcut mode
[ 1417.001319] Magic number: 3:318:133
[ 1417.003338] Freeing unused kernel memory: 328k freed
[ 1417.009125] Time: tsc clocksource has been installed.
[ 1417.030657] input: AT Translated Set 2 keyboard as /class/input/input1
[ 1419.420999] Capability LSM initialized
[ 1420.045104] thermal: Unknown symbol acpi_processor_set_thermal_limit
[ 1423.027688] PIIX4: IDE controller at PCI slot 0000:00:07.1
[ 1423.027738] PIIX4: chipset revision 1
[ 1423.027749] PIIX4: not 100% native mode: will probe irqs later
[ 1423.027773] ide0: BM-DMA at 0x2020-0x2027, BIOS settings: hda:DMA,
hdb:DMA
[ 1423.027815] Probing IDE interface ide0...
[ 1423.417605] hda: IC25N080ATMR04-0, ATA DISK drive
[ 1423.417881] usbcore: registered new interface driver usbfs
[ 1423.418044] usbcore: registered new interface driver hub
[ 1423.418309] usbcore: registered new device driver usb
[ 1423.418507] Floppy drive(s): fd0 is 1.44M
[ 1423.432168] USB Universal Host Controller Interface driver v3.0
[ 1423.554778] FDC 0 is a post-1991 82077
[ 1423.895935] hdb: TOSHIBA CD-ROM XM-1902B, ATAPI CD/DVD-ROM drive
[ 1423.985952] ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
[ 1424.081514] SCSI subsystem initialized
[ 1424.179523] libata version 2.20 loaded.
[ 1424.204189] PCI: Found IRQ 11 for device 0000:00:07.2
[ 1424.204250] uhci_hcd 0000:00:07.2: UHCI Host Controller
[ 1424.204779] uhci_hcd 0000:00:07.2: new USB bus registered, assigned bus
number 1
[ 1424.204849] uhci_hcd 0000:00:07.2: irq 11, io base 0x00002000
[ 1424.205384] usb usb1: configuration #1 chosen from 1 choice
[ 1424.205592] hub 1-0:1.0: USB hub found
[ 1424.205652] hub 1-0:1.0: 2 ports detected
[ 1424.520491] hdb: ATAPI 24X CD-ROM drive, 128kB Cache, DMA
[ 1424.520522] Uniform CD-ROM driver Revision: 3.20
[ 1424.595437] usb 1-1: new full speed USB device using uhci_hcd and address 2
[ 1424.605510] hda: max request size: 512KiB
[ 1424.802944] usb 1-1: configuration #1 chosen from 1 choice
[ 1425.025035] usbcore: registered new interface driver hiddev
[ 1425.036178] input: USB AUDIO as /class/input/input2
[ 1425.036249] input: USB HID v1.10 Device [USB AUDIO ] on usb-0000:00:07.2-1
[ 1425.073528] input: USB AUDIO as /class/input/input3
[ 1425.073590] input: USB HID v1.10 Device [USB AUDIO ] on usb-0000:00:07.2-1
[ 1425.073644] usbcore: registered new interface driver usbhid
[ 1425.073658] drivers/usb/input/hid-core.c: v2.6:USB HID core driver
[ 1425.285317] hda: 156301488 sectors (80026 MB) w/7884KiB Cache,
CHS=16383/255/63, UDMA(33)
[ 1425.286921] hda: cache flushes supported
[ 1425.287067] hda:<4>hda: dma_timer_expiry: dma status == 0x61
[ 1455.270081] hda: DMA timeout error
[ 1455.270103] hda: dma timeout error: status=0x58 { DriveReady SeekComplete
DataRequest }
[ 1455.270120] ide: failed opcode was: unknown
[ 1455.522874] hda1 <<4>hda: dma_timer_expiry: dma status == 0x61
[ 1485.505015] hda: DMA timeout error
[ 1485.505038] hda: dma timeout error: status=0x58 { DriveReady SeekComplete
DataRequest }
[ 1485.505054] ide: failed opcode was: unknown
[ 1485.514071] hda5 hda6 > hda2 hda3 hda4
[ 1505.614982] hda: dma_timer_expiry: dma status == 0x61
[ 1515.610011] hda: DMA timeout error
[ 1515.610034] hda: dma timeout error: status=0x58 { DriveReady SeekComplete
DataRequest }
[ 1515.610051] ide: failed opcode was: unknown
[ 1535.600063] hda: dma_timer_expiry: dma status == 0x61
[ 1545.595082] hda: DMA timeout error
[ 1545.595105] hda: dma timeout error: status=0x58 { DriveReady SeekComplete
DataRequest }
[ 1545.595122] ide: failed opcode was: unknown
[ 1546.229724] Attempting manual resume
[ 1546.229743] swsusp: Resume From Partition 3:6
[ 1546.229751] PM: Checking swsusp image.
[ 1546.237894] PM: Resume from disk failed.
[ 1546.420792] kjournald starting. Commit interval 5 seconds
[ 1546.420851] EXT3-fs: mounted filesystem with ordered data mode.
[ 1577.841353] Linux agpgart interface v0.102 (c) Dave Jones
[ 1577.870666] agpgart: Detected an Intel 440BX Chipset.
[ 1577.876678] agpgart: AGP aperture is 64M @ 0x44000000
[ 1578.629901] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 1578.793350] Yenta: CardBus bridge found at 0000:00:11.0 [0e11:b121]
[ 1578.793387] Yenta: Enabling burst memory read transactions
[ 1578.793401] Yenta: Using CSCINT to route CSC interrupts to PCI
[ 1578.793410] Yenta: Routing CardBus interrupts to PCI
[ 1578.793424] Yenta TI: socket 0000:00:11.0, mfunc 0x01001c72, devctl 0x64
[ 1579.039232] Yenta: ISA IRQ mask 0x0698, PCI irq 11
[ 1579.039248] Socket status: 30000020
[ 1579.039806] Yenta: CardBus bridge found at 0000:00:11.1 [0e11:b121]
[ 1579.039845] Yenta: Using CSCINT to route CSC interrupts to PCI
[ 1579.039856] Yenta: Routing CardBus interrupts to PCI
[ 1579.039869] Yenta TI: socket 0000:00:11.1, mfunc 0x01001c72, devctl 0x64
[ 1579.289223] Yenta: ISA IRQ mask 0x0698, PCI irq 11
[ 1579.289239] Socket status: 30000006
[ 1579.316366] piix4_smbus 0000:00:07.3: Found 0000:00:07.3 device
[ 1579.316404] piix4_smbus 0000:00:07.3: Host SMBus controller not enabled!
[ 1579.318408] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 1579.698125] pccard: CardBus card inserted into slot 0
[ 1579.996840] parport: PnPBIOS parport detected.
[ 1579.996892] parport0: PC-style at 0x378, irq 7 [PCSPP,TRISTATE,EPP]
[ 1581.566652] irda_init()
[ 1581.566710] NET: Registered protocol family 23
[ 1582.430492] Synaptics Touchpad, model: 1, fw: 4.3, id: 0x8e58a1, caps:
0x0/0x0
[ 1582.513774] input: SynPS/2 Synaptics TouchPad as /class/input/input4
[ 1583.266245] input: PC Speaker as /class/input/input5
[ 1584.778550] PCI: Enabling device 0000:02:00.0 (0000 -> 0003)
[ 1584.778583] PCI: Setting latency timer of device 0000:02:00.0 to 64
[ 1584.779130] eth0: Xircom cardbus revision 3 at irq 11
[ 1585.337601] cs: IO port probe 0x100-0x3af: excluding 0x100-0x107 0x220-0x237
0x260-0x267 0x300-0x307 0x388-0x38f
[ 1585.339886] cs: IO port probe 0x3e0-0x4ff: excluding 0x4d0-0x4d7
[ 1585.341111] cs: IO port probe 0x820-0x8ff: clean.
[ 1585.342133] cs: IO port probe 0xc00-0xcf7: clean.
[ 1585.343959] cs: IO port probe 0xa00-0xaff: clean.
[ 1585.347594] cs: IO port probe 0x100-0x3af: excluding 0x100-0x107 0x220-0x237
0x260-0x267 0x300-0x307 0x388-0x38f
[ 1585.349959] cs: IO port probe 0x3e0-0x4ff: excluding 0x4d0-0x4d7
[ 1585.351104] cs: IO port probe 0x820-0x8ff: clean.
[ 1585.352127] cs: IO port probe 0xc00-0xcf7: clean.
[ 1585.353975] cs: IO port probe 0xa00-0xaff: clean.
[ 1586.272249] usbcore: registered new interface driver snd-usb-audio
[ 1587.080696] lp0: using parport0 (interrupt-driven).
[ 1587.225136] fuse init (API version 7.8)
[ 1587.427771] Adding 695448k swap on
/dev/disk/by-uuid/6d5b0d72-a1dd-4515-a0c3-af830e02d4fa. Priority:-1 extents:1
across:695448k
[ 1587.606267] EXT3 FS on hda3, internal journal
[ 1588.306775] FAT: utf8 is not a recommended IO charset for FAT filesystems,
filesystem will be case sensitive!
[ 1588.973587] xircom cardbus adaptor found, registering as eth0, using irq 11
[ 1588.973652] xircom_cb: Link status has changed
[ 1588.973665] xircom_cb: Link is 100 mbit
[ 1590.315886] NET: Registered protocol family 17
[ 1594.073396] NET: Registered protocol family 10
[ 1594.073838] lo: Disabled Privacy Extensions
[ 1596.720965] acpi_cpufreq: Unknown symbol acpi_processor_notify_smm
[ 1596.721770] acpi_cpufreq: Unknown symbol
acpi_processor_unregister_performance
[ 1596.724083] acpi_cpufreq: Unknown symbol
acpi_processor_preregister_performance
[ 1596.725252] acpi_cpufreq: Unknown symbol acpi_processor_register_performance
[ 1604.255840] eth0: no IPv6 routers present
[ 1626.898703] ppdev: user-space parallel port driver
[ 1632.311965] apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
[ 1640.491032] Bluetooth: Core ver 2.11
[ 1640.491271] NET: Registered protocol family 31
[ 1640.491285] Bluetooth: HCI device and connection manager initialized
[ 1640.491299] Bluetooth: HCI socket layer initialized
[ 1640.637671] Bluetooth: L2CAP ver 2.8
[ 1640.637727] Bluetooth: L2CAP socket layer initialized
[ 1640.685299] Bluetooth: RFCOMM socket layer initialized
[ 1640.685347] Bluetooth: RFCOMM TTY layer initialized
[ 1640.685358] Bluetooth: RFCOMM ver 1.8
[ 1745.902714] pccard: card ejected from slot 0
[ 1792.212233] pccard: CardBus card inserted into slot 0
[ 1792.212648] PCI: Enabling device 0000:02:00.0 (0000 -> 0003)
[ 1792.212680] PCI: Setting latency timer of device 0000:02:00.0 to 64
[ 1792.213223] eth0: Xircom cardbus revision 3 at irq 11
[ 1792.710197] xircom cardbus adaptor found, registering as eth0, using irq 11
[ 1794.362833] xircom_cb: Link status has changed
[ 1794.362860] xircom_cb: Link is 100 mbit
[ 1819.198732] eth0: no IPv6 routers present
NOTE THAT THIS IS ON THE SAME SYSTEM RUNNING THE 2.6.20-13 KERNEL!!!
It also boots fine into Windows 2000pro
It will NOT boot into the 2.6.20-14 kernel!!! I cannot run diagnostics
in the same system with the -14 kernel!!
I get the following messages:
ata1.00:exceptonEmask 0x0 sAct0x0Serr0x0action0x2frozen
ata1.00:cmd c8/00:08:00:00:00/00:00:00:00:00/e0tag0cdb 0x1e data 4096 in
These messages loop 6 times, then this message appears:
buffer I/O error on device sda, logical block 0
This cycle then repeats continuously until you give the system a warm
boot ( cntl-alt-del ).
--
Latest download hard crashes Armada 1750
https://bugs.launchpad.net/bugs/104211
You received this bug notification because you are a member of Ubuntu
Bugs, which is the bug contact for Ubuntu.
--
ubuntu-bugs mailing list
ubuntu-bugs@lists.ubuntu.com
https://lists.ubuntu.com/mailman/listinfo/ubuntu-bugs
