output of dmesg.

** Description changed:

  After today's upgrades when I boot to feisty (both recovery and normal)
  the system hangs for about 15-25 seconds on "Configuring network
  interfaces."
  
- Here is the output of dmesg:
- 
- ##DMESG START
- [    0.000000] Linux version 2.6.20-13-generic ([EMAIL PROTECTED]) (gcc 
version 4.1.2 (Ubuntu 4.1.2-0ubuntu4)) #2 SMP Sun Mar 25 00:21:25 UTC 2007 
(Ubuntu 2.6.20-13.21-generic)
- [    0.000000] BIOS-provided physical RAM map:
- [    0.000000] sanitize start
- [    0.000000] sanitize end
- [    0.000000] copy_e820_map() start: 0000000000000000 size: 000000000009f800 
end: 000000000009f800 type: 1
- [    0.000000] copy_e820_map() type is E820_RAM
- [    0.000000] copy_e820_map() start: 000000000009f800 size: 0000000000000800 
end: 00000000000a0000 type: 2
- [    0.000000] copy_e820_map() start: 00000000000d0000 size: 0000000000030000 
end: 0000000000100000 type: 2
- [    0.000000] copy_e820_map() start: 0000000000100000 size: 0000000077da0000 
end: 0000000077ea0000 type: 1
- [    0.000000] copy_e820_map() type is E820_RAM
- [    0.000000] copy_e820_map() start: 0000000077ea0000 size: 000000000000c000 
end: 0000000077eac000 type: 3
- [    0.000000] copy_e820_map() start: 0000000077eac000 size: 0000000000054000 
end: 0000000077f00000 type: 4
- [    0.000000] copy_e820_map() start: 0000000077f00000 size: 0000000008100000 
end: 0000000080000000 type: 2
- [    0.000000] copy_e820_map() start: 00000000e0000000 size: 0000000010000000 
end: 00000000f0000000 type: 2
- [    0.000000] copy_e820_map() start: 00000000fec00000 size: 0000000000010000 
end: 00000000fec10000 type: 2
- [    0.000000] copy_e820_map() start: 00000000fee00000 size: 0000000000001000 
end: 00000000fee01000 type: 2
- [    0.000000] copy_e820_map() start: 00000000fff80000 size: 0000000000080000 
end: 0000000100000000 type: 2
- [    0.000000]  BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
- [    0.000000]  BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
- [    0.000000]  BIOS-e820: 00000000000d0000 - 0000000000100000 (reserved)
- [    0.000000]  BIOS-e820: 0000000000100000 - 0000000077ea0000 (usable)
- [    0.000000]  BIOS-e820: 0000000077ea0000 - 0000000077eac000 (ACPI data)
- [    0.000000]  BIOS-e820: 0000000077eac000 - 0000000077f00000 (ACPI NVS)
- [    0.000000]  BIOS-e820: 0000000077f00000 - 0000000080000000 (reserved)
- [    0.000000]  BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved)
- [    0.000000]  BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved)
- [    0.000000]  BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
- [    0.000000]  BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
- [    0.000000] 1022MB HIGHMEM available.
- [    0.000000] 896MB LOWMEM available.
- [    0.000000] found SMP MP-table at 000f7c50
- [    0.000000] Entering add_active_range(0, 0, 491168) 0 entries of 256 used
- [    0.000000] Zone PFN ranges:
- [    0.000000]   DMA             0 ->     4096
- [    0.000000]   Normal       4096 ->   229376
- [    0.000000]   HighMem    229376 ->   491168
- [    0.000000] early_node_map[1] active PFN ranges
- [    0.000000]     0:        0 ->   491168
- [    0.000000] On node 0 totalpages: 491168
- [    0.000000]   DMA zone: 32 pages used for memmap
- [    0.000000]   DMA zone: 0 pages reserved
- [    0.000000]   DMA zone: 4064 pages, LIFO batch:0
- [    0.000000]   Normal zone: 1760 pages used for memmap
- [    0.000000]   Normal zone: 223520 pages, LIFO batch:31
- [    0.000000]   HighMem zone: 2045 pages used for memmap
- [    0.000000]   HighMem zone: 259747 pages, LIFO batch:31
- [    0.000000] DMI present.
- [    0.000000] ACPI: RSDP (v000 PTLTD                                 ) @ 
0x000f7c20
- [    0.000000] ACPI: RSDT (v001 PTLTD    RSDT   0x06040000  LTP 0x00000000) @ 
0x77ea4577
- [    0.000000] ACPI: FADT (v001 HP     Piranha  0x06040000 ATI  0x000f4240) @ 
0x77eabe1a
- [    0.000000] ACPI: SSDT (v001 PTLTD  POWERNOW 0x06040000  LTP 0x00000001) @ 
0x77eabe8e
- [    0.000000] ACPI: MADT (v001 PTLTD          APIC   0x06040000  LTP 
0x00000000) @ 0x77eabf7e
- [    0.000000] ACPI: MCFG (v001 PTLTD    MCFG   0x06040000  LTP 0x00000000) @ 
0x77eabfc4
- [    0.000000] ACPI: DSDT (v001     HP     309B 0x06040000 MSFT 0x0100000e) @ 
0x00000000
- [    0.000000] ATI board detected. Disabling timer routing over 8254.
- [    0.000000] ACPI: PM-Timer IO Port: 0x8008
- [    0.000000] ACPI: Local APIC address 0xfee00000
- [    0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
- [    0.000000] Processor #0 15:4 APIC version 16
- [    0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
- [    0.000000] ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
- [    0.000000] IOAPIC[0]: apic_id 1, version 33, address 0xfec00000, GSI 0-23
- [    0.000000] ACPI: IRQ9 used by override.
- [    0.000000] Enabling APIC mode:  Flat.  Using 1 I/O APICs
- [    0.000000] Using ACPI (MADT) for SMP configuration information
- [    0.000000] Allocating PCI resources starting at 88000000 (gap: 
80000000:60000000)
- [    0.000000] Detected 1994.447 MHz processor.
- [   12.375751] Built 1 zonelists.  Total pages: 487331
- [   12.375754] Kernel command line: 
root=UUID=016b6f9a-d55c-48a9-b83c-3f009a21ac5c ro splash
- [   12.375880] mapped APIC to ffffd000 (fee00000)
- [   12.375882] mapped IOAPIC to ffffc000 (fec00000)
- [   12.375886] Enabling fast FPU save and restore... done.
- [   12.375888] Enabling unmasked SIMD FPU exception support... done.
- [   12.375898] Initializing CPU#0
- [   12.375963] PID hash table entries: 4096 (order: 12, 16384 bytes)
- [   12.376873] Console: colour VGA+ 80x25
- [   12.379772] Dentry cache hash table entries: 131072 (order: 7, 524288 
bytes)
- [   12.380267] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
- [   12.436657] Memory: 1936740k/1964672k available (1992k kernel code, 26644k 
reserved, 889k data, 328k init, 1047168k highmem)
- [   12.436719] virtual kernel memory layout:
- [   12.436720]     fixmap  : 0xfff4e000 - 0xfffff000   ( 708 kB)
- [   12.436721]     pkmap   : 0xff800000 - 0xffc00000   (4096 kB)
- [   12.436723]     vmalloc : 0xf8800000 - 0xff7fe000   ( 111 MB)
- [   12.436724]     lowmem  : 0xc0000000 - 0xf8000000   ( 896 MB)
- [   12.436725]       .init : 0xc03d7000 - 0xc0429000   ( 328 kB)
- [   12.436726]       .data : 0xc02f2184 - 0xc03d06d4   ( 889 kB)
- [   12.436728]       .text : 0xc0100000 - 0xc02f2184   (1992 kB)
- [   12.437070] Checking if this processor honours the WP bit even in 
supervisor mode... Ok.
- [   12.515846] Calibrating delay using timer specific routine.. 3992.59 
BogoMIPS (lpj=7985187)
- [   12.515971] Security Framework v1.0.0 initialized
- [   12.516021] SELinux:  Disabled at boot.
- [   12.516076] Mount-cache hash table entries: 512
- [   12.516257] CPU: After generic identify, caps: 078bfbff e3d3fbff 00000000 
00000000 00000001 00000000 00000001
- [   12.516265] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 
bytes/line)
- [   12.516311] CPU: L2 Cache: 1024K (64 bytes/line)
- [   12.516355] CPU: After all inits, caps: 078bfbff e3d3fbff 00000000 
00000410 00000001 00000000 00000001
- [   12.516367] Compat vDSO mapped to ffffe000.
- [   12.516413] Remapping vsyscall page to ffffe000
- [   12.516464] Checking 'hlt' instruction... OK.
- [   12.532015] SMP alternatives: switching to UP code
- [   12.532304] Freeing SMP alternatives: 11k freed
- [   12.532540] Early unpacking initramfs... done
- [   12.813956] ACPI: Core revision 20060707
- [   12.814206] ACPI: Looking for DSDT in initramfs... error, file /DSDT.aml 
not found.
- [   13.454818] CPU0: AMD Turion(tm) 64 Mobile Technology ML-37 stepping 02
- [   13.454949] Total of 1 processors activated (3992.59 BogoMIPS).
- [   13.455169] ENABLING IO-APIC IRQs
- [   13.455396] ..TIMER: vector=0x31 apic1=0 pin1=0 apic2=-1 pin2=-1
- [   13.602905] Brought up 1 CPUs
- [   13.603122] Booting paravirtualized kernel on bare hardware
- [   13.603247] Time:  0:14:19  Date: 03/04/107
- [   13.603316] NET: Registered protocol family 16
- [   13.603424] EISA bus registered
- [   13.603469] ACPI: bus type pci registered
- [   13.603566] PCI: PCI BIOS revision 2.10 entry at 0xfd86c, last bus=8
- [   13.603611] PCI: Using configuration type 1
- [   13.603654] Setting up standard PCI resources
- [   13.605618] ACPI: Interpreter enabled
- [   13.605662] ACPI: Using IOAPIC for interrupt routing
- [   13.606098] ACPI: PCI Root Bridge [PCI0] (0000:00)
- [   13.606144] PCI: Probing PCI hardware (bus 00)
- [   13.607799] Boot video device is 0000:01:05.0
- [   13.608432] PCI: Transparent bridge - 0000:00:14.4
- [   13.608568] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
- [   13.610298] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PB5_._PRT]
- [   13.611079] ACPI: PCI Interrupt Link [LNKA] (IRQs 10 11) *0, disabled.
- [   13.611523] ACPI: PCI Interrupt Link [LNKB] (IRQs 10 11) *0, disabled.
- [   13.611966] ACPI: PCI Interrupt Link [LNKC] (IRQs 10 11) *0, disabled.
- [   13.612410] ACPI: PCI Interrupt Link [LNKD] (IRQs 10 11) *0, disabled.
- [   13.612855] ACPI: PCI Interrupt Link [LNKE] (IRQs 10 11) *0, disabled.
- [   13.613298] ACPI: PCI Interrupt Link [LNKF] (IRQs 10 11) *0, disabled.
- [   13.613743] ACPI: PCI Interrupt Link [LNKG] (IRQs 10 11) *0, disabled.
- [   13.614187] ACPI: PCI Interrupt Link [LNKH] (IRQs 10 11) *0, disabled.
- [   13.658919] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P2P_._PRT]
- [   13.659130] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGP_._PRT]
- [   13.659522] Linux Plug and Play Support v0.97 (c) Adam Belay
- [   13.659571] pnp: PnP ACPI init
- [   13.682857] pnp: PnP ACPI: found 10 devices
- [   13.682903] PnPBIOS: Disabled by ACPI PNP
- [   13.682978] PCI: Using ACPI for IRQ routing
- [   13.683022] PCI: If a device doesn't work, try "pci=routeirq".  If it 
helps, post a report
- [   13.683075] PCI: Cannot allocate resource region 7 of bridge 0000:00:05.0
- [   13.683120] PCI: Cannot allocate resource region 8 of bridge 0000:00:05.0
- [   13.707131] NET: Registered protocol family 8
- [   13.707175] NET: Registered protocol family 20
- [   13.707356] pnp: 00:08: ioport range 0x1080-0x1080 has been reserved
- [   13.707402] pnp: 00:08: ioport range 0x40b-0x40b has been reserved
- [   13.707448] pnp: 00:08: ioport range 0x4d0-0x4d1 has been reserved
- [   13.707493] pnp: 00:08: ioport range 0x4d6-0x4d6 has been reserved
- [   13.707538] pnp: 00:08: ioport range 0x870-0x87f has been reserved
- [   13.707770] PCI: Bridge: 0000:00:01.0
- [   13.707814]   IO window: 9000-9fff
- [   13.707858]   MEM window: b0100000-b01fffff
- [   13.707903]   PREFETCH window: c0000000-cfffffff
- [   13.707947] PCI: Bridge: 0000:00:05.0
- [   13.707990]   IO window: disabled.
- [   13.708033]   MEM window: disabled.
- [   13.708076]   PREFETCH window: disabled.
- [   13.708123] PCI: Bus 7, cardbus bridge: 0000:06:04.0
- [   13.708167]   IO window: 0000a400-0000a4ff
- [   13.708214]   IO window: 0000a800-0000a8ff
- [   13.708261]   PREFETCH window: 88000000-8bffffff
- [   13.708309]   MEM window: 8c000000-8fffffff
- [   13.708356] PCI: Bridge: 0000:00:14.4
- [   13.708400]   IO window: a000-afff
- [   13.708448]   MEM window: b0200000-b02fffff
- [   13.708494]   PREFETCH window: 88000000-8bffffff
- [   13.708553] PCI: Setting latency timer of device 0000:00:05.0 to 64
- [   13.708579] ACPI: PCI Interrupt 0000:06:04.0[A] -> GSI 20 (level, low) -> 
IRQ 16
- [   13.708696] NET: Registered protocol family 2
- [   13.742813] IP route cache hash table entries: 32768 (order: 5, 131072 
bytes)
- [   13.743015] TCP established hash table entries: 131072 (order: 8, 1048576 
bytes)
- [   13.744044] TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
- [   13.744627] TCP: Hash tables configured (established 131072 bind 65536)
- [   13.744673] TCP reno registered
- [   13.754867] checking if image is initramfs... it is
- [   14.309745] Freeing initrd memory: 6780k freed
- [   14.310169] audit: initializing netlink socket (disabled)
- [   14.310225] audit(1175645658.380:1): initialized
- [   14.310330] highmem bounce pool size: 64 pages
- [   14.310438] VFS: Disk quotas dquot_6.5.1
- [   14.310497] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
- [   14.310584] io scheduler noop registered
- [   14.310663] io scheduler anticipatory registered
- [   14.310743] io scheduler deadline registered
- [   14.310832] io scheduler cfq registered (default)
- [   14.311130] PCI: Setting latency timer of device 0000:00:05.0 to 64
- [   14.311150] assign_interrupt_mode Found MSI capability
- [   14.311195] Allocate Port Service[0000:00:05.0:pcie00]
- [   14.311293] isapnp: Scanning for PnP cards...
- [   14.665491] isapnp: No Plug & Play device found
- [   14.689357] Real Time Clock Driver v1.12ac
- [   14.689439] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ 
sharing enabled
- [   14.690039] ACPI: PCI Interrupt 0000:00:14.6[B] -> GSI 17 (level, low) -> 
IRQ 17
- [   14.690131] ACPI: PCI interrupt for device 0000:00:14.6 disabled
- [   14.690232] mice: PS/2 mouse device common for all mice
- [   14.690682] RAMDISK driver initialized: 16 RAM disks of 65536K size 1024 
blocksize
- [   14.690853] input: Macintosh mouse button emulation as /class/input/input0
- [   14.690923] Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
- [   14.690969] ide: Assuming 33MHz system bus speed for PIO modes; override 
with idebus=xx
- [   14.691263] PNP: PS/2 Controller [PNP0303:KBC0,PNP0f13:MSE0] at 0x60,0x64 
irq 1,12
- [   14.710599] i8042.c: Detected active multiplexing controller, rev 1.1.
- [   14.726663] serio: i8042 KBD port at 0x60,0x64 irq 1
- [   14.726708] serio: i8042 AUX0 port at 0x60,0x64 irq 12
- [   14.726753] serio: i8042 AUX1 port at 0x60,0x64 irq 12
- [   14.726797] serio: i8042 AUX2 port at 0x60,0x64 irq 12
- [   14.726842] serio: i8042 AUX3 port at 0x60,0x64 irq 12
- [   14.727768] EISA: Probing bus 0 at eisa.0
- [   14.727818] Cannot allocate resource for EISA slot 1
- [   14.727887] Cannot allocate resource for EISA slot 8
- [   14.727931] EISA: Detected 0 cards.
- [   14.758027] TCP cubic registered
- [   14.758076] NET: Registered protocol family 1
- [   14.758135] Using IPI No-Shortcut mode
- [   14.758228] ACPI: (supports S0 S3 S4 S5)
- [   14.758484]   Magic number: 3:450:202
- [   14.758555]   hash matches device ttyt0
- [   14.759004] Freeing unused kernel memory: 328k freed
- [   14.761825] Time: tsc clocksource has been installed.
- [   14.766208] input: AT Translated Set 2 keyboard as /class/input/input1
- [   15.986957] Capability LSM initialized
- [   16.051521] ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3])
- [   16.051527] ACPI: Processor [CPU0] (supports 8 throttling states)
- [   16.060428] ACPI Exception (acpi_thermal-0412): AE_NOT_FOUND, Invalid 
active threshold [0] [20060707]
- [    2.952000] ACPI: Thermal Zone [THRM] (0 C)
- [    2.960000] Time: acpi_pm clocksource has been installed.
- [    3.440000] usbcore: registered new interface driver usbfs
- [    3.440000] usbcore: registered new interface driver hub
- [    3.440000] usbcore: registered new device driver usb
- [    3.440000] ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) 
Driver
- [    3.440000] ACPI: PCI Interrupt 0000:00:13.0[A] -> GSI 19 (level, low) -> 
IRQ 18
- [    3.440000] ohci_hcd 0000:00:13.0: OHCI Host Controller
- [    3.440000] ohci_hcd 0000:00:13.0: new USB bus registered, assigned bus 
number 1
- [    3.440000] ohci_hcd 0000:00:13.0: irq 18, io mem 0xb0000000
- [    3.468000] SCSI subsystem initialized
- [    3.472000] libata version 2.20 loaded.
- [    3.532000] usb usb1: configuration #1 chosen from 1 choice
- [    3.532000] hub 1-0:1.0: USB hub found
- [    3.532000] hub 1-0:1.0: 4 ports detected
- [    3.568000] ieee1394: Initialized config rom entry `ip1394'
- [    3.600000] 8139cp: 10/100 PCI Ethernet driver v1.3 (Mar 22, 2004)
- [    3.636000] ACPI: PCI Interrupt 0000:00:13.1[A] -> GSI 19 (level, low) -> 
IRQ 18
- [    3.636000] ohci_hcd 0000:00:13.1: OHCI Host Controller
- [    3.636000] ohci_hcd 0000:00:13.1: new USB bus registered, assigned bus 
number 2
- [    3.636000] ohci_hcd 0000:00:13.1: irq 18, io mem 0xb0001000
- [    3.696000] usb usb2: configuration #1 chosen from 1 choice
- [    3.696000] hub 2-0:1.0: USB hub found
- [    3.696000] hub 2-0:1.0: 4 ports detected
- [    3.800000] ATIIXP: IDE controller at PCI slot 0000:00:14.1
- [    3.800000] ACPI: PCI Interrupt 0000:00:14.1[A] -> GSI 16 (level, low) -> 
IRQ 19
- [    3.800000] ATIIXP: chipset revision 0
- [    3.800000] ATIIXP: not 100% native mode: will probe irqs later
- [    3.800000]     ide0: BM-DMA at 0x8410-0x8417, BIOS settings: hda:DMA, 
hdb:pio
- [    3.800000]     ide1: BM-DMA at 0x8418-0x841f, BIOS settings: hdc:DMA, 
hdd:pio
- [    3.800000] Probing IDE interface ide0...
- [    3.940000] usb 1-4: new full speed USB device using ohci_hcd and address 2
- [    4.092000] hda: ST9120824A, ATA DISK drive
- [    4.144000] usb 1-4: configuration #1 chosen from 1 choice
- [    4.452000] usb 2-2: new full speed USB device using ohci_hcd and address 2
- [    4.664000] usb 2-2: configuration #1 chosen from 1 choice
- [    4.684000] usbcore: registered new interface driver hiddev
- [    4.696000] input: Logitech USB Gaming Mouse as /class/input/input2
- [    4.696000] input: USB HID v1.11 Mouse [Logitech USB Gaming Mouse] on 
usb-0000:00:13.1-2
- [    4.708000] hiddev96: USB HID v1.11 Device [Logitech USB Gaming Mouse] on 
usb-0000:00:13.1-2
- [    4.708000] usbcore: registered new interface driver usbhid
- [    4.708000] drivers/usb/input/hid-core.c: v2.6:USB HID core driver
- [    4.764000] ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
- [    4.832000] Probing IDE interface ide1...
- [    5.568000] hdc: HL-DT-ST DVDRAM GSA-4084N, ATAPI CD/DVD-ROM drive
- [    5.904000] ide1 at 0x170-0x177,0x376 on irq 15
- [    5.908000] ACPI: PCI Interrupt 0000:00:13.2[A] -> GSI 19 (level, low) -> 
IRQ 18
- [    5.908000] ehci_hcd 0000:00:13.2: EHCI Host Controller
- [    5.908000] ehci_hcd 0000:00:13.2: new USB bus registered, assigned bus 
number 3
- [    5.908000] ehci_hcd 0000:00:13.2: irq 18, io mem 0xb0002000
- [    5.908000] ehci_hcd 0000:00:13.2: USB 2.0 started, EHCI 1.00, driver 10 
Dec 2004
- [    5.908000] usb 1-4: USB disconnect, address 2
- [    5.912000] usb usb3: configuration #1 chosen from 1 choice
- [    5.912000] hub 3-0:1.0: USB hub found
- [    5.912000] hub 3-0:1.0: 8 ports detected
- [    5.924000] hda: max request size: 128KiB
- [    5.924000] hda: 234441648 sectors (120034 MB) w/8192KiB Cache, 
CHS=65535/16/63, UDMA(100)
- [    5.928000] hda: cache flushes supported
- [    5.928000]  hda: hda1 hda2 <<6>ACPI: PCI Interrupt 0000:06:04.2[C] -> GSI 
23 (level, low) -> IRQ 20
- [    6.064000] usb 2-2: USB disconnect, address 2
- [    6.064000] ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[20]  
MMIO=[b0209000-b02097ff]  Max Packet=[2048]  IR/IT contexts=[4/8]
- [    6.064000] 8139cp 0000:06:06.0: This (id 10ec:8139 rev 10) is not an 
8139C+ compatible chip
- [    6.064000] 8139cp 0000:06:06.0: Try the "8139too" driver instead.
- [    6.064000] 8139too Fast Ethernet driver 0.9.28
- [    6.064000] ACPI: PCI Interrupt 0000:06:06.0[A] -> GSI 22 (level, low) -> 
IRQ 21
- [    6.068000] eth0: RealTek RTL8139 at 0xf8938400, 00:16:d4:03:33:2c, IRQ 21
- [    6.068000] eth0:  Identified 8139 chip type 'RTL-8100B/8139D'
- [    6.068000]  hda5 >
- [    6.076000] hdc: ATAPI 24X DVD-ROM DVD-R-RAM CD-R/RW drive, 2048kB Cache, 
DMA
- [    6.076000] Uniform CD-ROM driver Revision: 3.20
- [    6.316000] Attempting manual resume
- [    6.316000] swsusp: Resume From Partition 3:5
- [    6.316000] PM: Checking swsusp image.
- [    6.316000] PM: Resume from disk failed.
- [    6.368000] kjournald starting.  Commit interval 5 seconds
- [    6.368000] EXT3-fs: mounted filesystem with ordered data mode.
- [    6.864000] usb 2-2: new full speed USB device using ohci_hcd and address 3
- [    7.084000] usb 2-2: configuration #1 chosen from 1 choice
- [    7.096000] input: Logitech USB Gaming Mouse as /class/input/input3
- [    7.096000] input: USB HID v1.11 Mouse [Logitech USB Gaming Mouse] on 
usb-0000:00:13.1-2
- [    7.108000] hiddev96: USB HID v1.11 Device [Logitech USB Gaming Mouse] on 
usb-0000:00:13.1-2
- [    7.336000] ieee1394: Host added: ID:BUS[0-00:1023]  GUID[643f02003dec407d]
- [    7.412000] usb 1-4: new full speed USB device using ohci_hcd and address 3
- [    7.624000] usb 1-4: configuration #1 chosen from 1 choice
- [   18.840000] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
- [   18.844000] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
- [   18.904000] piix4_smbus 0000:00:14.0: Found 0000:00:14.0 device
- [   19.300000] Linux agpgart interface v0.102 (c) Dave Jones
- [   19.344000] sdhci: Secure Digital Host Controller Interface driver
- [   19.344000] sdhci: Copyright(c) Pierre Ossman
- [   19.344000] sdhci: SDHCI controller found at 0000:06:04.4 [104c:8034] (rev 
0)
- [   19.344000] ACPI: PCI Interrupt 0000:06:04.4[A] -> GSI 20 (level, low) -> 
IRQ 16
- [   19.344000] mmc0: SDHCI at 0xb020a000 irq 16 DMA
- [   19.348000] mmc1: SDHCI at 0xb0209c00 irq 16 DMA
- [   19.348000] mmc2: SDHCI at 0xb0209800 irq 16 DMA
- [   19.772000] Yenta: CardBus bridge found at 0000:06:04.0 [103c:30a4]
- [   19.772000] Yenta: Enabling burst memory read transactions
- [   19.772000] Yenta: Using INTVAL to route CSC interrupts to PCI
- [   19.772000] Yenta: Routing CardBus interrupts to ISA
- [   19.772000] Yenta TI: socket 0000:06:04.0, mfunc 0x00a61b22, devctl 0x64
- [   19.808000] Bluetooth: Core ver 2.11
- [   19.808000] NET: Registered protocol family 31
- [   19.808000] Bluetooth: HCI device and connection manager initialized
- [   19.808000] Bluetooth: HCI socket layer initialized
- [   19.856000] Bluetooth: HCI USB driver ver 2.9
- [   19.952000] ieee80211_crypt: registered algorithm 'NULL'
- [   19.964000] ieee80211: 802.11 data/management/control stack, git-1.1.13
- [   19.964000] ieee80211: Copyright (C) 2004-2005 Intel Corporation <[EMAIL 
PROTECTED]>
- [   19.988000] usbcore: registered new interface driver hci_usb
- [   19.988000] usbcore: registered new interface driver xpad
- [   19.988000] drivers/usb/input/xpad.c: driver for Xbox controllers v0.1.6
- [   20.004000] Yenta: ISA IRQ mask 0x0cf8, PCI irq 16
- [   20.004000] Socket status: 30000820
- [   20.004000] pcmcia: parent PCI bridge I/O window: 0xa000 - 0xafff
- [   20.004000] cs: IO port probe 0xa000-0xafff: clean.
- [   20.004000] pcmcia: parent PCI bridge Memory window: 0xb0200000 - 
0xb02fffff
- [   20.004000] pcmcia: parent PCI bridge Memory window: 0x88000000 - 
0x8bffffff
- [   20.012000] ACPI: PCI Interrupt 0000:06:04.3[B] -> GSI 23 (level, low) -> 
IRQ 20
- [   20.028000] input: PC Speaker as /class/input/input4
- [   20.132000] ACPI: PCI Interrupt 0000:00:14.5[B] -> GSI 17 (level, low) -> 
IRQ 17
- [   20.160000] bcm43xx driver
- [   20.160000] ACPI: PCI Interrupt 0000:06:02.0[A] -> GSI 21 (level, low) -> 
IRQ 22
- [   20.276000] ACPI: PCI Interrupt 0000:00:14.6[B] -> GSI 17 (level, low) -> 
IRQ 17
- [   20.388000] MC'97 0 converters and GPIO not ready (0x1)
- [   20.648000] pccard: CardBus card inserted into slot 0
- [   20.664000] Synaptics Touchpad, model: 1, fw: 6.2, id: 0x1a0b1, caps: 
0xa04713/0x200000
- [   20.732000] input: SynPS/2 Synaptics TouchPad as /class/input/input5
- [   20.748000] PCI: Enabling device 0000:07:00.0 (0000 -> 0001)
- [   20.748000] ACPI: PCI Interrupt 0000:07:00.0[A] -> GSI 20 (level, low) -> 
IRQ 16
- [   20.748000] PCI: Setting latency timer of device 0000:07:00.0 to 64
- [   20.760000] Audigy2 value: Special config.
- [   20.780000] cs: IO port probe 0x100-0x3af: clean.
- [   20.784000] cs: IO port probe 0x3e0-0x4ff: clean.
- [   20.784000] cs: IO port probe 0x820-0x8ff: clean.
- [   20.784000] cs: IO port probe 0xc00-0xcf7: excluding 0xc00-0xc07 
0xc10-0xc17 0xc50-0xc57 0xc68-0xc6f 0xcd0-0xcdf
- [   20.788000] cs: IO port probe 0xa00-0xaff: clean.
- [   21.052000] fuse init (API version 7.8)
- [   21.112000] lp: driver loaded but no devices found
- [   21.172000] Adding 4803392k swap on 
/dev/disk/by-uuid/8e0c8e29-9e87-4c10-b4e7-480a6ddf6797.  Priority:-1 extents:1 
across:4803392k
- [   21.344000] EXT3 FS on hda1, internal journal
- [   21.604000] eth0: link up, 10Mbps, half-duplex, lpa 0x0000
- [   22.744000] NET: Registered protocol family 17
- [   26.584000] NET: Registered protocol family 10
- [   26.952000] lo: Disabled Privacy Extensions
- [   26.952000] ADDRCONF(NETDEV_UP): eth1: link is not ready
- [  102.024000] input: Power Button (FF) as /class/input/input6
- [  102.028000] ACPI: Power Button (FF) [PWRF]
- [  102.060000] input: Sleep Button (FF) as /class/input/input7
- [  102.064000] ACPI: Sleep Button (FF) [SLPF]
- [  102.096000] input: Lid Switch as /class/input/input8
- [  102.100000] ACPI: Lid Switch [LID]
- [  102.128000] input: Power Button (CM) as /class/input/input9
- [  102.132000] ACPI: Power Button (CM) [PWRB]
- [  102.228000] Using specific hotkey driver
- [  102.300000] ACPI: Battery Slot [BAT1] (battery present)
- [  102.328000] No dock devices found.
- [  102.348000] ACPI: AC Adapter [ACAD] (on-line)
- [  102.384000] ACPI: Video Device [VGA] (multi-head: yes  rom: no  post: no)
- [  102.404000] ibm_acpi: ec object not found
- [  102.432000] wmi_add device=df8bb400
- [  102.432000] calling WQBA
- [  102.440000] pcc_acpi: loading...
- [  102.708000] powernow-k8: Found 1 AMD Turion(tm) 64 Mobile Technology ML-37 
processors (version 2.00.00)
- [  102.708000] powernow-k8:    0 : fid 0xc (2000 MHz), vid 0x4
- [  102.708000] powernow-k8:    1 : fid 0xa (1800 MHz), vid 0x6
- [  102.708000] powernow-k8:    2 : fid 0x8 (1600 MHz), vid 0x8
- [  102.708000] powernow-k8:    3 : fid 0x0 (800 MHz), vid 0x16
- [  102.708000] powernow-k8: ph2 null fid transition 0xc
- [  108.924000] fglrx: module license 'Proprietary. (C) 2002 - ATI 
Technologies, Starnberg, GERMANY' taints kernel.
- [  108.932000] [fglrx] Maximum main memory to use for locked dma buffers: 
1777 MBytes.
- [  108.932000] [fglrx] module loaded - fglrx 8.34.8 [Feb 20 2007] on minor 0
- [  109.000000] ACPI: PCI Interrupt 0000:01:05.0[A] -> GSI 17 (level, low) -> 
IRQ 17
- [  109.076000] ppdev: user-space parallel port driver
- [  110.440000] [fglrx] total      GART = 130023424
- [  110.440000] [fglrx] free       GART = 114032640
- [  110.440000] [fglrx] max single GART = 114032640
- [  110.440000] [fglrx] total      LFB  = 134217728
- [  110.440000] [fglrx] free       LFB  = 119828480
- [  110.440000] [fglrx] max single LFB  = 119828480
- [  110.440000] [fglrx] total      Inv  = 134217728
- [  110.440000] [fglrx] free       Inv  = 134217728
- [  110.440000] [fglrx] max single Inv  = 134217728
- [  110.440000] [fglrx] total      TIM  = 0
- [  111.968000] apm: BIOS not found.
- [  112.136000] Bluetooth: L2CAP ver 2.8
- [  112.136000] Bluetooth: L2CAP socket layer initialized
- [  112.184000] Bluetooth: RFCOMM socket layer initialized
- [  112.184000] Bluetooth: RFCOMM TTY layer initialized
- [  112.184000] Bluetooth: RFCOMM ver 1.8
- [  167.464000] SoftMAC: Authentication timed out with 02:18:de:37:78:11
- [ 1194.612000] psmouse.c: TouchPad at isa0060/serio4/input0 lost sync at byte 
4
- [ 1194.620000] psmouse.c: TouchPad at isa0060/serio4/input0 lost sync at byte 
4
- [ 1194.636000] psmouse.c: TouchPad at isa0060/serio4/input0 - driver 
resynched.
- [ 1194.644000] psmouse.c: TouchPad at isa0060/serio4/input0 lost sync at byte 
4
- [ 1194.644000] psmouse.c: TouchPad at isa0060/serio4/input0 lost sync at byte 
1
- [ 1194.656000] psmouse.c: TouchPad at isa0060/serio4/input0 lost sync at byte 
4
- [ 1194.660000] psmouse.c: TouchPad at isa0060/serio4/input0 lost sync at byte 
1
- [ 1194.676000] psmouse.c: TouchPad at isa0060/serio4/input0 - driver 
resynched.
- [ 1194.684000] psmouse.c: TouchPad at isa0060/serio4/input0 lost sync at byte 
4
- [ 1194.684000] psmouse.c: TouchPad at isa0060/serio4/input0 lost sync at byte 
1
- [ 1194.692000] psmouse.c: TouchPad at isa0060/serio4/input0 - driver 
resynched.
- [ 1194.736000] psmouse.c: Failed to reset mouse on isa0060/serio1
- [ 1194.740000] psmouse.c: TouchPad at isa0060/serio4/input0 lost sync at byte 
4
- [ 1194.740000] psmouse.c: TouchPad at isa0060/serio4/input0 lost sync at byte 
1
- [ 1194.756000] psmouse.c: TouchPad at isa0060/serio4/input0 lost sync at byte 
1
- [ 1194.756000] psmouse.c: TouchPad at isa0060/serio4/input0 lost sync at byte 
1
- [ 1194.756000] psmouse.c: TouchPad at isa0060/serio4/input0 lost sync at byte 
1
- [ 1194.756000] psmouse.c: issuing reconnect request
- [ 1195.048000] input: PS/2 Generic Mouse as /class/input/input10
- [ 1195.052000] psmouse.c: Failed to enable mouse on isa0060/serio1
- [ 2157.976000] psmouse.c: TouchPad at isa0060/serio4/input0 lost sync at byte 
1
- [ 2157.980000] psmouse.c: TouchPad at isa0060/serio4/input0 lost sync at byte 
1
- [ 2157.980000] psmouse.c: TouchPad at isa0060/serio4/input0 lost sync at byte 
1
- [ 2157.984000] psmouse.c: TouchPad at isa0060/serio4/input0 lost sync at byte 
1
- [ 2157.984000] psmouse.c: TouchPad at isa0060/serio4/input0 lost sync at byte 
1
- [ 2157.984000] psmouse.c: issuing reconnect request
- ##DMESG END
- 
- and lspci -vv
- 
- ##LSPCI -VV START
- 00:00.0 Host bridge: ATI Technologies Inc RS480 Host Bridge (rev 01)
-       Subsystem: Hewlett-Packard Company Unknown device 30a4
-       Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- 
Stepping- SERR- FastB2B-
-       Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- 
<TAbort- <MAbort+ >SERR- <PERR-
-       Latency: 64
- 
- 00:01.0 PCI bridge: ATI Technologies Inc RS480 PCI Bridge (prog-if 00 [Normal 
decode])
-       Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- 
Stepping- SERR- FastB2B-
-       Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- 
<TAbort- <MAbort- >SERR- <PERR-
-       Latency: 64
-       Bus: primary=00, secondary=01, subordinate=01, sec-latency=64
-       I/O behind bridge: 00009000-00009fff
-       Memory behind bridge: b0100000-b01fffff
-       Prefetchable memory behind bridge: 00000000c0000000-00000000cfffffff
-       Secondary status: 66MHz+ FastB2B- ParErr- DEVSEL=medium >TAbort- 
<TAbort- <MAbort+ <SERR- <PERR-
-       BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B-
-       Capabilities: [44] HyperTransport: MSI Mapping
-       Capabilities: [b0] Subsystem: Hewlett-Packard Company Unknown device 
30a4
- 
- 00:05.0 PCI bridge: ATI Technologies Inc Unknown device 5a37 (prog-if 00 
[Normal decode])
-       Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- 
Stepping- SERR- FastB2B-
-       Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- 
<MAbort- >SERR- <PERR-
-       Latency: 0
-       Bus: primary=00, secondary=02, subordinate=03, sec-latency=0
-       Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- 
<MAbort- <SERR- <PERR-
-       BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
-       Capabilities: [50] Power Management version 3
-               Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA 
PME(D0+,D1-,D2-,D3hot+,D3cold+)
-               Status: D0 PME-Enable- DSel=0 DScale=0 PME-
-       Capabilities: [58] Express Root Port (Slot-) IRQ 0
-               Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag+
-               Device: Latency L0s <64ns, L1 <1us
-               Device: Errors: Correctable+ Non-Fatal+ Fatal+ Unsupported+
-               Device: RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
-               Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
-               Link: Supported Speed 2.5Gb/s, Width x2, ASPM L0s L1, Port 247
-               Link: Latency L0s unlimited, L1 unlimited
-               Link: ASPM Disabled RCB 64 bytes CommClk- ExtSynch-
-               Link: Speed 2.5Gb/s, Width x16
-               Root: Correctable- Non-Fatal- Fatal- PME-
-       Capabilities: [80] Message Signalled Interrupts: Mask- 64bit- Queue=0/0 
Enable-
-               Address: 00000000  Data: 0000
-       Capabilities: [b0] Subsystem: ATI Technologies Inc Unknown device 5950
-       Capabilities: [b8] HyperTransport: MSI Mapping
- 
- 00:13.0 USB Controller: ATI Technologies Inc IXP SB400 USB Host Controller 
(prog-if 10 [OHCI])
-       Subsystem: ATI Technologies Inc IXP SB400 USB Host Controller
-       Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- 
Stepping- SERR- FastB2B-
-       Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- 
<TAbort- <MAbort- >SERR- <PERR-
-       Latency: 64, Cache Line Size: 64 bytes
-       Interrupt: pin A routed to IRQ 18
-       Region 0: Memory at b0000000 (32-bit, non-prefetchable) [size=4K]
-       Capabilities: [d0] Message Signalled Interrupts: Mask- 64bit- Queue=0/0 
Enable-
-               Address: 00000000  Data: 0000
- 
- 00:13.1 USB Controller: ATI Technologies Inc IXP SB400 USB Host Controller 
(prog-if 10 [OHCI])
-       Subsystem: ATI Technologies Inc IXP SB400 USB Host Controller
-       Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- 
Stepping- SERR- FastB2B-
-       Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- 
<TAbort- <MAbort- >SERR- <PERR-
-       Latency: 64, Cache Line Size: 64 bytes
-       Interrupt: pin A routed to IRQ 18
-       Region 0: Memory at b0001000 (32-bit, non-prefetchable) [size=4K]
-       Capabilities: [d0] Message Signalled Interrupts: Mask- 64bit- Queue=0/0 
Enable-
-               Address: 00000000  Data: 0000
- 
- 00:13.2 USB Controller: ATI Technologies Inc IXP SB400 USB2 Host Controller 
(prog-if 20 [EHCI])
-       Subsystem: ATI Technologies Inc IXP SB400 USB2 Host Controller
-       Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- 
Stepping- SERR- FastB2B-
-       Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- 
<TAbort- <MAbort- >SERR- <PERR-
-       Latency: 64, Cache Line Size: 64 bytes
-       Interrupt: pin A routed to IRQ 18
-       Region 0: Memory at b0002000 (32-bit, non-prefetchable) [size=4K]
-       Capabilities: [dc] Power Management version 2
-               Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA 
PME(D0+,D1+,D2+,D3hot+,D3cold-)
-               Status: D0 PME-Enable- DSel=0 DScale=0 PME-
-               Bridge: PM- B3+
-       Capabilities: [d0] Message Signalled Interrupts: Mask- 64bit- Queue=0/0 
Enable-
-               Address: 00000000  Data: 0000
- 
- 00:14.0 SMBus: ATI Technologies Inc IXP SB400 SMBus Controller (rev 11)
-       Subsystem: Hewlett-Packard Company Unknown device 30a4
-       Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- 
Stepping- SERR- FastB2B-
-       Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- 
<TAbort- <MAbort- >SERR- <PERR-
-       Region 0: I/O ports at 8400 [size=16]
-       Region 1: Memory at b0003000 (32-bit, non-prefetchable) [size=1K]
-       Capabilities: [b0] HyperTransport: MSI Mapping
- 
- 00:14.1 IDE interface: ATI Technologies Inc Standard Dual Channel PCI IDE 
Controller ATI (prog-if 8a [Master SecP PriP])
-       Subsystem: Hewlett-Packard Company Unknown device 30a4
-       Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- 
Stepping- SERR- FastB2B-
-       Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- 
<TAbort- <MAbort- >SERR- <PERR-
-       Latency: 0
-       Interrupt: pin A routed to IRQ 19
-       Region 0: I/O ports at 01f0 [size=8]
-       Region 1: I/O ports at 03f4 [size=1]
-       Region 2: I/O ports at 0170 [size=8]
-       Region 3: I/O ports at 0374 [size=1]
-       Region 4: I/O ports at 8410 [size=16]
-       Capabilities: [70] Message Signalled Interrupts: Mask- 64bit- Queue=0/0 
Enable-
-               Address: 00000000  Data: 0000
- 
- 00:14.3 ISA bridge: ATI Technologies Inc IXP SB400 PCI-ISA Bridge
-       Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- 
Stepping- SERR- FastB2B-
-       Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- 
<TAbort- <MAbort- >SERR- <PERR-
-       Latency: 0
- 
- 00:14.4 PCI bridge: ATI Technologies Inc IXP SB400 PCI-PCI Bridge (prog-if 01 
[Subtractive decode])
-       Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- 
Stepping- SERR- FastB2B-
-       Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- 
<TAbort- <MAbort- >SERR- <PERR-
-       Latency: 64
-       Bus: primary=00, secondary=06, subordinate=08, sec-latency=64
-       I/O behind bridge: 0000a000-0000afff
-       Memory behind bridge: b0200000-b02fffff
-       Prefetchable memory behind bridge: 88000000-8bffffff
-       Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- 
<TAbort- <MAbort+ <SERR- <PERR-
-       BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
- 
- 00:14.5 Multimedia audio controller: ATI Technologies Inc IXP SB400 AC'97 
Audio Controller (rev 02)
-       Subsystem: Hewlett-Packard Company Unknown device 30a4
-       Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- 
Stepping- SERR- FastB2B-
-       Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=slow >TAbort- <TAbort- 
<MAbort- >SERR- <PERR-
-       Latency: 64 (500ns min), Cache Line Size: 32 bytes
-       Interrupt: pin B routed to IRQ 17
-       Region 0: Memory at b0003400 (32-bit, non-prefetchable) [size=256]
-       Capabilities: [40] Message Signalled Interrupts: Mask- 64bit- Queue=0/0 
Enable-
-               Address: 00000000  Data: 0000
- 
- 00:14.6 Modem: ATI Technologies Inc ATI SB400 - AC'97 Modem Controller (rev 
02) (prog-if 00 [Generic])
-       Subsystem: Hewlett-Packard Company Unknown device 30a4
-       Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- 
Stepping- SERR- FastB2B-
-       Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=slow >TAbort- <TAbort- 
<MAbort- >SERR- <PERR-
-       Latency: 64 (500ns min), Cache Line Size: 32 bytes
-       Interrupt: pin B routed to IRQ 17
-       Region 0: Memory at b0003800 (32-bit, non-prefetchable) [size=256]
-       Capabilities: [40] Message Signalled Interrupts: Mask- 64bit- Queue=0/0 
Enable-
-               Address: 00000000  Data: 0000
- 
- 00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] 
HyperTransport Technology Configuration
-       Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- 
Stepping- SERR- FastB2B-
-       Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- 
<MAbort- >SERR- <PERR-
-       Capabilities: [80] HyperTransport: Host or Secondary Interface
-               !!! Possibly incomplete decoding
-               Command: WarmRst+ DblEnd-
-               Link Control: CFlE- CST- CFE- <LkFail- Init+ EOC- TXO- <CRCErr=8
-               Link Config: MLWI=16bit MLWO=16bit LWI=16bit LWO=16bit
-               Revision ID: 1.02
- 
- 00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] 
Address Map
-       Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- 
Stepping- SERR- FastB2B-
-       Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- 
<MAbort- >SERR- <PERR-
- 
- 00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM 
Controller
-       Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- 
Stepping- SERR- FastB2B-
-       Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- 
<MAbort- >SERR- <PERR-
- 
- 00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] 
Miscellaneous Control
-       Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- 
Stepping- SERR- FastB2B-
-       Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- 
<MAbort- >SERR- <PERR-
- 
- 01:05.0 VGA compatible controller: ATI Technologies Inc ATI Radeon XPRESS 
200M 5955 (PCIE) (prog-if 00 [VGA])
-       Subsystem: Hewlett-Packard Company Unknown device 30a4
-       Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- 
Stepping- SERR- FastB2B-
-       Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- 
<TAbort- <MAbort- >SERR- <PERR-
-       Latency: 255 (2000ns min), Cache Line Size: 32 bytes
-       Interrupt: pin A routed to IRQ 17
-       Region 0: Memory at c0000000 (32-bit, prefetchable) [size=256M]
-       Region 1: I/O ports at 9000 [size=256]
-       Region 2: Memory at b0100000 (32-bit, non-prefetchable) [size=64K]
-       [virtual] Expansion ROM at b0120000 [disabled] [size=128K]
-       Capabilities: [50] Power Management version 2
-               Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA 
PME(D0-,D1-,D2-,D3hot-,D3cold-)
-               Status: D0 PME-Enable- DSel=0 DScale=0 PME-
- 
- 06:02.0 Network controller: Broadcom Corporation BCM4311 [AirForce 54g] 
802.11a/b/g PCI Express Transceiver (rev 02)
-       Subsystem: Hewlett-Packard Company Unknown device 1358
-       Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- 
Stepping- SERR- FastB2B-
-       Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- 
<MAbort- >SERR- <PERR-
-       Latency: 64
-       Interrupt: pin A routed to IRQ 22
-       Region 0: Memory at b0204000 (32-bit, non-prefetchable) [size=8K]
- 
- 06:04.0 CardBus bridge: Texas Instruments PCIxx21/x515 Cardbus Controller
-       Subsystem: Hewlett-Packard Company Unknown device 30a4
-       Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- 
Stepping- SERR- FastB2B-
-       Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- 
<TAbort- <MAbort- >SERR- <PERR-
-       Latency: 168, Cache Line Size: 128 bytes
-       Interrupt: pin A routed to IRQ 16
-       Region 0: Memory at b0208000 (32-bit, non-prefetchable) [size=4K]
-       Bus: primary=06, secondary=07, subordinate=07, sec-latency=176
-       Memory window 0: 88000000-8bfff000 (prefetchable)
-       Memory window 1: 8c000000-8ffff000
-       I/O window 0: 0000a400-0000a4ff
-       I/O window 1: 0000a800-0000a8ff
-       BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset- 16bInt- PostWrite+
-       16-bit legacy interface ports at 0001
- 
- 06:04.2 FireWire (IEEE 1394): Texas Instruments OHCI Compliant IEEE 1394 Host 
Controller (prog-if 10 [OHCI])
-       Subsystem: Hewlett-Packard Company Unknown device 30a4
-       Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- 
Stepping- SERR- FastB2B-
-       Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- 
<TAbort- <MAbort- >SERR- <PERR-
-       Latency: 64 (500ns min, 1000ns max), Cache Line Size: 32 bytes
-       Interrupt: pin C routed to IRQ 20
-       Region 0: Memory at b0209000 (32-bit, non-prefetchable) [size=2K]
-       Region 1: Memory at b0200000 (32-bit, non-prefetchable) [size=16K]
-       Capabilities: [44] Power Management version 2
-               Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA 
PME(D0+,D1+,D2+,D3hot+,D3cold-)
-               Status: D0 PME-Enable- DSel=0 DScale=0 PME+
- 
- 06:04.3 Mass storage controller: Texas Instruments PCIxx21 Integrated 
FlashMedia Controller
-       Subsystem: Hewlett-Packard Company Unknown device 30a4
-       Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- 
Stepping- SERR- FastB2B-
-       Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- 
<TAbort- <MAbort- >SERR- <PERR-
-       Latency: 64 (1750ns min, 1000ns max), Cache Line Size: 32 bytes
-       Interrupt: pin B routed to IRQ 20
-       Region 0: Memory at b0206000 (32-bit, non-prefetchable) [size=8K]
-       Capabilities: [44] Power Management version 2
-               Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA 
PME(D0+,D1+,D2+,D3hot+,D3cold-)
-               Status: D0 PME-Enable- DSel=0 DScale=0 PME-
- 
- 06:04.4 Generic system peripheral [0805]: Texas Instruments 
PCI6411/6421/6611/6621/7411/7421/7611/7621 Secure Digital Controller
-       Subsystem: Hewlett-Packard Company Unknown device 30a4
-       Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- 
Stepping- SERR- FastB2B-
-       Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- 
<TAbort- <MAbort- >SERR- <PERR-
-       Latency: 64 (1750ns min, 1000ns max), Cache Line Size: 32 bytes
-       Interrupt: pin A routed to IRQ 16
-       Region 0: Memory at b020a000 (32-bit, non-prefetchable) [size=256]
-       Region 1: Memory at b0209c00 (32-bit, non-prefetchable) [size=256]
-       Region 2: Memory at b0209800 (32-bit, non-prefetchable) [size=256]
-       Capabilities: [80] Power Management version 2
-               Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA 
PME(D0+,D1+,D2+,D3hot+,D3cold-)
-               Status: D0 PME-Enable- DSel=0 DScale=0 PME-
- 
- 06:06.0 Ethernet controller: Realtek Semiconductor Co., Ltd. 
RTL-8139/8139C/8139C+ (rev 10)
-       Subsystem: Hewlett-Packard Company Unknown device 30a4
-       Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- 
Stepping- SERR- FastB2B-
-       Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- 
<TAbort- <MAbort- >SERR- <PERR-
-       Latency: 128 (8000ns min, 16000ns max)
-       Interrupt: pin A routed to IRQ 21
-       Region 0: I/O ports at a000 [size=256]
-       Region 1: Memory at b020a400 (32-bit, non-prefetchable) [size=256]
-       Capabilities: [50] Power Management version 2
-               Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA 
PME(D0-,D1+,D2+,D3hot+,D3cold+)
-               Status: D0 PME-Enable- DSel=0 DScale=0 PME-
- 
- 07:00.0 Multimedia audio controller: Creative Labs SB0400 Audigy2 Value
-       Subsystem: Creative Labs Unknown device 2001
-       Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- 
Stepping- SERR- FastB2B-
-       Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- 
<TAbort- <MAbort- >SERR- <PERR-
-       Latency: 64 (500ns min, 5000ns max)
-       Interrupt: pin A routed to IRQ 16
-       Region 0: I/O ports at a400 [size=64]
-       Capabilities: [dc] Power Management version 2
-               Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA 
PME(D0-,D1-,D2-,D3hot-,D3cold-)
-               Status: D0 PME-Enable- DSel=0 DScale=0 PME-
- ##LSPCI -VV END
- 
- hope that's all you need, if anything else is needed please let me know
- I'm happy to help as always.
+ hope that's all you need, if anything else is needed please let me know I'm 
happy to help as always.
+ EDIT: dmesg and lspci moved into files. sorry about that :)

** Attachment added: "dmesg.txt"
   http://librarian.launchpad.net/7143591/dmesg.txt

-- 
Feisty boot hangs on "Configuring network interfaces"
https://bugs.launchpad.net/bugs/102675
You received this bug notification because you are a member of Ubuntu
Bugs, which is the bug contact for Ubuntu.

-- 
ubuntu-bugs mailing list
ubuntu-bugs@lists.ubuntu.com
https://lists.ubuntu.com/mailman/listinfo/ubuntu-bugs

Reply via email to