00:00.0 Host bridge [0600]: Intel Corporation 82G33/G31/P35/P31 Express DRAM
Controller [8086:29c0] (rev 10)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort+ >SERR- <PERR-
Latency: 0
Capabilities: <access denied>
00:01.0 PCI bridge [0604]: Intel Corporation 82G33/G31/P35/P31 Express PCI
Express Root Port [8086:29c1] (rev 10) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
Capabilities: <access denied>
00:02.0 VGA compatible controller [0300]: Intel Corporation 82G33/G31 Express
Integrated Graphics Controller [8086:29c2] (rev 10) (prog-if 00 [VGA
controller])
Subsystem: Intel Corporation 82G33/G31 Express Integrated Graphics
Controller [8086:29c2]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 11
Region 0: Memory at ff900000 (32-bit, non-prefetchable) [size=512K]
Region 1: I/O ports at f140 [size=8]
Region 2: Memory at d0000000 (32-bit, prefetchable) [size=256M]
Region 3: Memory at ff700000 (32-bit, non-prefetchable) [size=1M]
Capabilities: <access denied>
00:1c.0 PCI bridge [0604]: Intel Corporation 82801G (ICH7 Family) PCI Express
Port 1 [8086:27d0] (rev 01) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
Capabilities: <access denied>
00:1c.1 PCI bridge [0604]: Intel Corporation 82801G (ICH7 Family) PCI Express
Port 2 [8086:27d2] (rev 01) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=03, subordinate=03, sec-latency=0
I/O behind bridge: 0000e000-0000efff
Memory behind bridge: ff800000-ff8fffff
Prefetchable memory behind bridge: 00000000e4000000-00000000e40fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
Capabilities: <access denied>
00:1d.0 USB Controller [0c03]: Intel Corporation 82801G (ICH7 Family) USB UHCI
Controller #1 [8086:27c8] (rev 01) (prog-if 00 [UHCI])
Subsystem: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller
#1 [8086:27c8]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 23
Region 4: I/O ports at f080 [size=32]
00:1d.1 USB Controller [0c03]: Intel Corporation 82801G (ICH7 Family) USB UHCI
Controller #2 [8086:27c9] (rev 01) (prog-if 00 [UHCI])
Subsystem: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller
#2 [8086:27c9]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin B routed to IRQ 19
Region 4: I/O ports at f060 [size=32]
00:1d.2 USB Controller [0c03]: Intel Corporation 82801G (ICH7 Family) USB UHCI
Controller #3 [8086:27ca] (rev 01) (prog-if 00 [UHCI])
Subsystem: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller
#3 [8086:27ca]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin C routed to IRQ 18
Region 4: I/O ports at f040 [size=32]
00:1d.3 USB Controller [0c03]: Intel Corporation 82801G (ICH7 Family) USB UHCI
Controller #4 [8086:27cb] (rev 01) (prog-if 00 [UHCI])
Subsystem: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller
#4 [8086:27cb]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin D routed to IRQ 16
Region 4: I/O ports at f020 [size=32]
00:1d.7 USB Controller [0c03]: Intel Corporation 82801G (ICH7 Family) USB2 EHCI
Controller [8086:27cc] (rev 01) (prog-if 20 [EHCI])
Subsystem: Intel Corporation 82801G (ICH7 Family) USB2 EHCI Controller
[8086:27cc]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 23
Region 0: Memory at ff980000 (32-bit, non-prefetchable) [size=1K]
Capabilities: <access denied>
00:1e.0 PCI bridge [0604]: Intel Corporation 82801 PCI Bridge [8086:244e] (rev
e1) (prog-if 01 [Subtractive decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0
Bus: primary=00, secondary=04, subordinate=04, sec-latency=32
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
Capabilities: <access denied>
00:1f.0 ISA bridge [0601]: Intel Corporation 82801GB/GR (ICH7 Family) LPC
Interface Bridge [8086:27b8] (rev 01)
Subsystem: Intel Corporation DeskTop Board D945GTP [8086:544e]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Capabilities: <access denied>
00:1f.1 IDE interface [0101]: Intel Corporation 82801G (ICH7 Family) IDE
Controller [8086:27df] (rev 01) (prog-if 8a [Master SecP PriP])
Subsystem: Intel Corporation 82801G (ICH7 Family) IDE Controller
[8086:27df]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 16
Region 0: I/O ports at 01f0 [size=8]
Region 1: I/O ports at 03f4 [size=1]
Region 2: I/O ports at 0170 [size=8]
Region 3: I/O ports at 0374 [size=1]
Region 4: I/O ports at f0f0 [size=16]
00:1f.2 IDE interface [0101]: Intel Corporation 82801GB/GR/GH (ICH7 Family)
SATA IDE Controller [8086:27c0] (rev 01) (prog-if 8f [Master SecP SecO PriP
PriO])
Subsystem: Intel Corporation 82801GB/GR/GH (ICH7 Family) SATA IDE
Controller [8086:27c0]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin B routed to IRQ 17
Region 0: I/O ports at f0e0 [size=8]
Region 1: I/O ports at f0d0 [size=4]
Region 2: I/O ports at f0c0 [size=8]
Region 3: I/O ports at f0b0 [size=4]
Region 4: I/O ports at f0a0 [size=16]
Capabilities: <access denied>
00:1f.3 SMBus [0c05]: Intel Corporation 82801G (ICH7 Family) SMBus Controller
[8086:27da] (rev 01)
Subsystem: Intel Corporation Unknown device [8086:d608]
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin B routed to IRQ 10
Region 4: I/O ports at f000 [size=32]
03:00.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd.
RTL8111/8168B PCI Express Gigabit Ethernet controller [10ec:8168] (rev 01)
Subsystem: Intel Corporation Unknown device [8086:d608]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 764
Region 0: I/O ports at e000 [size=256]
Region 2: Memory at ff820000 (64-bit, non-prefetchable) [size=4K]
[virtual] Expansion ROM at e4000000 [disabled] [size=128K]
Capabilities: <access denied>
please try cgroup_disable=memory option if you don't want
Memory: 4107656k/4980736k available (6263k kernel code, 73384k reserved, 1949k
data, 380k init, 3270900k highmem)
virtual kernel memory layout:
fixmap : 0xffee9000 - 0xfffff000 (1112 kB)
pkmap : 0xffa00000 - 0xffc00000 (2048 kB)
vmalloc : 0xf81fe000 - 0xff9fe000 ( 120 MB)
lowmem : 0xc0000000 - 0xf79fe000 ( 889 MB)
.init : 0xc090f000 - 0xc096e000 ( 380 kB)
.data : 0xc071de65 - 0xc09053ec (1949 kB)
.text : 0xc0100000 - 0xc071de65 (6263 kB)
Checking if this processor honours the WP bit even in supervisor mode...Ok.
hpet clockevent registered
HPET: 3 timers in total, 0 timers will be used for per-cpu timer
Calibrating delay loop (skipped), value calculated using timer frequency..
5999.86 BogoMIPS (lpj=11999732)
Mount-cache hash table entries: 512
Initializing cgroup subsys ns
Initializing cgroup subsys cpuacct
Initializing cgroup subsys memory
Initializing cgroup subsys devices
Initializing cgroup subsys freezer
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 6144K
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 0
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
using mwait in idle threads.
Checking 'hlt' instruction... OK.
ACPI: Core revision 20080926
..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
CPU0: Intel(R) Core(TM)2 CPU E8400 @ 3.00GHz stepping 0a
Booting processor 1 APIC 0x1 ip 0x6000
Initializing CPU#1
Calibrating delay using timer specific routine.. 5999.80 BogoMIPS (lpj=11999605)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 6144K
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 1
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#1.
CPU1: Intel(R) Core(TM)2 CPU E8400 @ 3.00GHz stepping 0a
checking TSC synchronization [CPU#0 -> CPU#1]: passed.
Brought up 2 CPUs
Total of 2 processors activated (11999.66 BogoMIPS).
net_namespace: 492 bytes
xor: automatically using best checksumming function: pIII_sse
pIII_sse : 11492.000 MB/sec
xor: using function: pIII_sse (11492.000 MB/sec)
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: MCFG configuration 0: base e0000000 segment 0 buses 0 - 64
PCI: Not using MMCONFIG.
PCI: Using configuration type 1 for base access
ACPI: EC: Look up EC in DSDT
ACPI: Interpreter enabled
ACPI: (supports S0 S1 S3 S4 S5)
ACPI: Using IOAPIC for interrupt routing
PCI: MCFG configuration 0: base e0000000 segment 0 buses 0 - 64
PCI: MCFG area at e0000000 reserved in ACPI motherboard resources
PCI: updated MCFG configuration 0: base e0000000 segment 0 buses 0 - 31
PCI: Using MMCONFIG for extended config space
ACPI: BIOS _OSI(Linux) query ignored
ACPI: No dock devices found.
ACPI: PCI Root Bridge [PCI0] (0000:00)
pci 0000:00:01.0: PME# supported from D0 D3hot D3cold
pci 0000:00:01.0: PME# disabled
pci 0000:00:02.0: reg 10 32bit mmio: [0xff900000-0xff97ffff]
pci 0000:00:02.0: reg 14 io port: [0xf140-0xf147]
pci 0000:00:02.0: reg 18 32bit mmio: [0xd0000000-0xdfffffff]
pci 0000:00:02.0: reg 1c 32bit mmio: [0xff700000-0xff7fffff]
pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
pci 0000:00:1c.0: PME# disabled
pci 0000:00:1c.1: PME# supported from D0 D3hot D3cold
pci 0000:00:1c.1: PME# disabled
pci 0000:00:1d.0: reg 20 io port: [0xf080-0xf09f]
pci 0000:00:1d.1: reg 20 io port: [0xf060-0xf07f]
pci 0000:00:1d.2: reg 20 io port: [0xf040-0xf05f]
pci 0000:00:1d.3: reg 20 io port: [0xf020-0xf03f]
pci 0000:00:1d.7: reg 10 32bit mmio: [0xff980000-0xff9803ff]
pci 0000:00:1d.7: PME# supported from D0 D3hot D3cold
pci 0000:00:1d.7: PME# disabled
pci 0000:00:1f.0: quirk: region 0400-047f claimed by ICH6 ACPI/GPIO/TCO
pci 0000:00:1f.0: quirk: region 0500-053f claimed by ICH6 GPIO
pci 0000:00:1f.1: reg 10 io port: [0xf130-0xf137]
pci 0000:00:1f.1: reg 14 io port: [0xf120-0xf123]
pci 0000:00:1f.1: reg 18 io port: [0xf110-0xf117]
pci 0000:00:1f.1: reg 1c io port: [0xf100-0xf103]
pci 0000:00:1f.1: reg 20 io port: [0xf0f0-0xf0ff]
pci 0000:00:1f.2: reg 10 io port: [0xf0e0-0xf0e7]
pci 0000:00:1f.2: reg 14 io port: [0xf0d0-0xf0d3]
pci 0000:00:1f.2: reg 18 io port: [0xf0c0-0xf0c7]
pci 0000:00:1f.2: reg 1c io port: [0xf0b0-0xf0b3]
pci 0000:00:1f.2: reg 20 io port: [0xf0a0-0xf0af]
pci 0000:00:1f.2: PME# supported from D3hot
pci 0000:00:1f.2: PME# disabled
pci 0000:00:1f.3: reg 20 io port: [0xf000-0xf01f]
pci 0000:03:00.0: reg 10 io port: [0xe000-0xe0ff]
pci 0000:03:00.0: reg 18 64bit mmio: [0xff820000-0xff820fff]
pci 0000:03:00.0: reg 30 32bit mmio: [0x000000-0x01ffff]
pci 0000:03:00.0: supports D1 D2
pci 0000:03:00.0: PME# supported from D1 D2 D3hot D3cold
pci 0000:03:00.0: PME# disabled
pci 0000:00:1c.1: bridge io port: [0xe000-0xefff]
pci 0000:00:1c.1: bridge 32bit mmio: [0xff800000-0xff8fffff]
pci 0000:00:1e.0: transparent bridge
bus 00 -> node 0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P2._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX1._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 *7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs *3 4 5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 10 11 12 14 15) *0
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 10 11 12 14 15) *0
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 10 11 12 14 15) *0
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 *5 6 7 10 11 12 14 15)
SCSI subsystem initialized
libata version 3.00 loaded.
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
PCI: Using ACPI for IRQ routing
hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0
hpet0: 3 comparators, 64-bit 14.318180 MHz counter
pnp: PnP ACPI init
ACPI: bus type pnp registered
pnp: PnP ACPI: found 11 devices
ACPI: ACPI bus type pnp unregistered
system 00:01: iomem range 0xfed14000-0xfed19fff has been reserved
system 00:01: iomem range 0xe0000000-0xe3ffffff has been reserved
system 00:02: ioport range 0x400-0x47f has been reserved
system 00:02: ioport range 0x1180-0x119f has been reserved
system 00:02: ioport range 0x500-0x53f has been reserved
system 00:02: iomem range 0xfec00000-0xfecfffff has been reserved
system 00:02: iomem range 0xfee00000-0xfee0ffff has been reserved
system 00:02: iomem range 0xfed1c000-0xfed1ffff has been reserved
system 00:02: iomem range 0xffb00000-0xffcfffff could not be reserved
system 00:02: iomem range 0xfc800000-0xfc800fff has been reserved
system 00:02: iomem range 0xfed20000-0xfed7ffff has been reserved
system 00:02: iomem range 0xffe00000-0xffffffff has been reserved
system 00:03: ioport range 0x290-0x29f has been reserved
system 00:08: ioport range 0x4d0-0x4d1 has been reserved
pci 0000:00:01.0: PCI bridge, secondary bus 0000:01
pci 0000:00:01.0: IO window: disabled
pci 0000:00:01.0: MEM window: disabled
pci 0000:00:01.0: PREFETCH window: disabled
pci 0000:00:1c.0: PCI bridge, secondary bus 0000:02
pci 0000:00:1c.0: IO window: disabled
pci 0000:00:1c.0: MEM window: disabled
pci 0000:00:1c.0: PREFETCH window: disabled
pci 0000:00:1c.1: PCI bridge, secondary bus 0000:03
pci 0000:00:1c.1: IO window: 0xe000-0xefff
pci 0000:00:1c.1: MEM window: 0xff800000-0xff8fffff
pci 0000:00:1c.1: PREFETCH window: 0x000000e4000000-0x000000e40fffff
pci 0000:00:1e.0: PCI bridge, secondary bus 0000:04
pci 0000:00:1e.0: IO window: disabled
pci 0000:00:1e.0: MEM window: disabled
pci 0000:00:1e.0: PREFETCH window: disabled
pci 0000:00:01.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
pci 0000:00:01.0: setting latency timer to 64
pci 0000:00:1c.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
pci 0000:00:1c.0: setting latency timer to 64
pci 0000:00:1c.1: PCI INT B -> GSI 17 (level, low) -> IRQ 17
pci 0000:00:1c.1: setting latency timer to 64
pci 0000:00:1e.0: setting latency timer to 64
bus: 00 index 0 io port: [0x00-0xffff]
bus: 00 index 1 mmio: [0x000000-0xffffffffffffffff]
bus: 01 index 0 mmio: [0x0-0x0]
bus: 01 index 1 mmio: [0x0-0x0]
bus: 01 index 2 mmio: [0x0-0x0]
bus: 01 index 3 mmio: [0x0-0x0]
bus: 02 index 0 mmio: [0x0-0x0]
bus: 02 index 1 mmio: [0x0-0x0]
bus: 02 index 2 mmio: [0x0-0x0]
bus: 02 index 3 mmio: [0x0-0x0]
bus: 03 index 0 io port: [0xe000-0xefff]
bus: 03 index 1 mmio: [0xff800000-0xff8fffff]
bus: 03 index 2 mmio: [0xe4000000-0xe40fffff]
bus: 03 index 3 mmio: [0x0-0x0]
bus: 04 index 0 mmio: [0x0-0x0]
bus: 04 index 1 mmio: [0x0-0x0]
bus: 04 index 2 mmio: [0x0-0x0]
bus: 04 index 3 io port: [0x00-0xffff]
bus: 04 index 4 mmio: [0x000000-0xffffffffffffffff]
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
NET: Registered protocol family 1
kvm: no hardware support
has_svm: not amd
kvm: no hardware support
Microcode Update Driver: v2.00 <tig...@aivazian.fsnet.co.uk>, Peter Oruba
highmem bounce pool size: 64 pages
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
DLM (built Jan 19 2009 11:08:05) installed
NTFS driver 2.1.29 [Flags: R/W].
fuse init (API version 7.10)
SGI XFS with ACLs, security attributes, large block numbers, no debug enabled
SGI XFS Quota Management subsystem
GFS2 (built Jan 19 2009 11:08:37) installed
Lock_DLM (built Jan 19 2009 11:08:40) installed
msgmni has been set to 1635
alg: No test for stdrng (krng)
async_tx: api initialized (sync-only)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered (default)
io scheduler cfq registered
pci 0000:00:02.0: Boot video device
pcieport-driver 0000:00:01.0: setting latency timer to 64
pcieport-driver 0000:00:01.0: found MSI capability
pcieport-driver 0000:00:01.0: irq 767 for MSI/MSI-X
pci_express 0000:00:01.0:pcie00: allocate port service
pci_express 0000:00:01.0:pcie03: allocate port service
pcieport-driver 0000:00:1c.0: setting latency timer to 64
pcieport-driver 0000:00:1c.0: found MSI capability
pcieport-driver 0000:00:1c.0: irq 766 for MSI/MSI-X
pci_express 0000:00:1c.0:pcie00: allocate port service
pci_express 0000:00:1c.0:pcie02: allocate port service
pci_express 0000:00:1c.0:pcie03: allocate port service
pcieport-driver 0000:00:1c.1: setting latency timer to 64
pcieport-driver 0000:00:1c.1: found MSI capability
pcieport-driver 0000:00:1c.1: irq 765 for MSI/MSI-X
pci_express 0000:00:1c.1:pcie00: allocate port service
pci_express 0000:00:1c.1:pcie02: allocate port service
pci_express 0000:00:1c.1:pcie03: allocate port service
processor ACPI_CPU:00: registered as cooling_device0
processor ACPI_CPU:01: registered as cooling_device1
intel_rng: Firmware space is locked read-only. If you can't or
intel_rng: don't want to disable this in firmware setup, and if
intel_rng: you are certain that your system has a functional
intel_rng: RNG, try using the 'no_fwh_detect' option.
Serial: 8250/16550 driver4 ports, IRQ sharing disabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
00:04: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
Switched to high resolution mode on CPU 1
Switched to high resolution mode on CPU 0
floppy0: no floppy controllers found
brd: module loaded
loop: module loaded
usbcore: registered new interface driver ub
Intel(R) PRO/1000 Network Driver - version 7.3.20-k3-NAPI
Copyright (c) 1999-2006 Intel Corporation.
e1000e: Intel(R) PRO/1000 Network Driver - 0.3.3.3-k6
e1000e: Copyright (c) 1999-2008 Intel Corporation.
Intel(R) Gigabit Ethernet Network Driver - version 1.2.45-k2
Copyright (c) 2008 Intel Corporation.
pcnet32.c:v1.35 21.Apr.2008 tsbog...@alpha.franken.de
e100: Intel(R) PRO/100 Network Driver, 3.5.23-k6-NAPI
e100: Copyright(c) 1999-2006 Intel Corporation
sky2 driver version 1.22
PPP generic driver version 2.4.2
PPP Deflate Compression module registered
PPP BSD Compression module registered
PPP MPPE Compression module registered
tun: Universal TUN/TAP device driver, 1.6
tun: (C) 1999-2004 Max Krasnyansky <m...@qualcomm.com>
r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded
r8169 0000:03:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
r8169 0000:03:00.0: setting latency timer to 64
r8169 0000:03:00.0: irq 764 for MSI/MSI-X
eth0: RTL8168b/8111b at 0xf8230000, 00:1c:c0:75:b5:28, XID 38500000 IRQ 764
Uniform Multi-Platform E-IDE driver
piix 0000:00:1f.1: IDE controller (0x8086:0x27df rev 0x01)
pci 0000:00:1f.1: PCI INT A -> GSI 16 (level, low) -> IRQ 16
piix 0000:00:1f.1: IDE port disabled
piix 0000:00:1f.1: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xf0f0-0xf0f7
Probing IDE interface ide0...
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide_generic: please use "probe_mask=0x3f" module parameter for probing all
legacy ISA IDE ports
ide-gd driver 1.18
Loading iSCSI transport class v2.0-870.
iscsi: registered transport (tcp)
megasas: 00.00.04.01 Thu July 24 11:41:51 PST 2008
3ware Storage Controller device driver for Linux v1.26.02.002.
3ware 9000 Storage Controller device driver for Linux v2.26.02.011.
Driver 'sd' needs updating - please use bus_type methods
ata_piix 0000:00:1f.2: version 2.12
ata_piix 0000:00:1f.2: PCI INT B -> GSI 17 (level, low) -> IRQ 17
ata_piix 0000:00:1f.2: MAP [ P0 P2 P1 P3 ]
ata_piix 0000:00:1f.2: setting latency timer to 64
scsi0 : ata_piix
scsi1 : ata_piix
ata1: SATA max UDMA/133 cmd 0xf0e0 ctl 0xf0d0 bmdma 0xf0a0 irq 17
ata2: SATA max UDMA/133 cmd 0xf0c0 ctl 0xf0b0 bmdma 0xf0a8 irq 17
ata1.00: ATA-8: ST3750330AS, SD1A, max UDMA/133
ata1.00: 1465149168 sectors, multi 16: LBA48 NCQ (depth 0/32)
ata1.00: configured for UDMA/133
ata2.00: ATA-8: ST3750330AS, SD1A, max UDMA/133
ata2.00: 1465149168 sectors, multi 16: LBA48 NCQ (depth 0/32)
ata2.00: configured for UDMA/133
scsi 0:0:0:0: Direct-Access ATA ST3750330AS SD1A PQ: 0 ANSI: 5
sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors: (750 GB/698 GiB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support
DPO or FUA
sd 0:0:0:0: [sda] 1465149168 512-byte hardware sectors: (750 GB/698 GiB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support
DPO or FUA
sda: sda1 sda2 sda3
sd 0:0:0:0: [sda] Attached SCSI disk
scsi 1:0:0:0: Direct-Access ATA ST3750330AS SD1A PQ: 0 ANSI: 5
sd 1:0:0:0: [sdb] 1465149168 512-byte hardware sectors: (750 GB/698 GiB)
sd 1:0:0:0: [sdb] Write Protect is off
sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support
DPO or FUA
sd 1:0:0:0: [sdb] 1465149168 512-byte hardware sectors: (750 GB/698 GiB)
sd 1:0:0:0: [sdb] Write Protect is off
sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support
DPO or FUA
sdb: sdb1 sdb2 sdb3
sd 1:0:0:0: [sdb] Attached SCSI disk
Fusion MPT base driver 3.04.07
Copyright (c) 1999-2008 LSI Corporation
Fusion MPT SPI Host driver 3.04.07
Fusion MPT SAS Host driver 3.04.07
Fusion MPT misc device (ioctl) driver 3.04.07
mptctl: Registered with Fusion MPT base driver
mptctl: /dev/mptctl @ (major,minor=10,220)
slram: not enough parameters.
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci_hcd 0000:00:1d.7: PCI INT A -> GSI 23 (level, low) -> IRQ 23
ehci_hcd 0000:00:1d.7: setting latency timer to 64
ehci_hcd 0000:00:1d.7: EHCI Host Controller
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:1d.7: debug port 1
ehci_hcd 0000:00:1d.7: cache line size of 32 is not supported
ehci_hcd 0000:00:1d.7: irq 23, io mem 0xff980000
ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 8 ports detected
uhci_hcd: USB Universal Host Controller Interface driver
uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23
uhci_hcd 0000:00:1d.0: setting latency timer to 64
uhci_hcd 0000:00:1d.0: UHCI Host Controller
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:1d.0: irq 23, io base 0x0000f080
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19
uhci_hcd 0000:00:1d.1: setting latency timer to 64
uhci_hcd 0000:00:1d.1: UHCI Host Controller
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:1d.1: irq 19, io base 0x0000f060
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
uhci_hcd 0000:00:1d.2: setting latency timer to 64
uhci_hcd 0000:00:1d.2: UHCI Host Controller
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:1d.2: irq 18, io base 0x0000f040
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
uhci_hcd 0000:00:1d.3: PCI INT D -> GSI 16 (level, low) -> IRQ 16
uhci_hcd 0000:00:1d.3: setting latency timer to 64
uhci_hcd 0000:00:1d.3: UHCI Host Controller
uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 5
uhci_hcd 0000:00:1d.3: irq 16, io base 0x0000f020
usb usb5: configuration #1 chosen from 1 choice
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 2 ports detected
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usbcore: registered new interface driver libusual
PNP: No PS/2 controller found. Probing ports directly.
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
coretemp coretemp.0: Using relative temperature scale!
coretemp coretemp.1: Using relative temperature scale!
w83627ehf: Found W83627DHG chip at 0x290
Software Watchdog Timer: 0.07 initialized. soft_noboot=0 soft_margin=60 sec
(nowayout= 0)
md: linear personality registered for level -1
md: raid0 personality registered for level 0
md: raid1 personality registered for level 1
md: raid10 personality registered for level 10
raid6: int32x1 1218 MB/s
raid6: int32x2 1140 MB/s
raid6: int32x4 966 MB/s
raid6: int32x8 855 MB/s
raid6: mmxx1 3767 MB/s
raid6: mmxx2 4231 MB/s
raid6: sse1x1 2570 MB/s
raid6: sse1x2 3479 MB/s
raid6: sse2x1 4783 MB/s
raid6: sse2x2 6058 MB/s
raid6: using algorithm sse2x2 (6058 MB/s)
md: raid6 personality registered for level 6
md: raid5 personality registered for level 5
md: raid4 personality registered for level 4
md: multipath personality registered for level -4
md: faulty personality registered for level -5
device-mapper: ioctl: 4.14.0-ioctl (2008-04-23) initialised: dm-de...@redhat.com
device-mapper: multipath: version 1.0.5 loaded
device-mapper: multipath round-robin: version 1.0.0 loaded
No iBFT detected.
usbcore: registered new interface driver usbkbd
usbkbd: :USB HID Boot Protocol keyboard driver
usbcore: registered new interface driver usbmouse
usbmouse: v1.6:USB HID Boot Protocol mouse driver
Netfilter messages via NETLINK v0.30.
nf_conntrack version 0.5.0 (16384 buckets, 65536 max)
CONFIG_NF_CT_ACCT is deprecated and will be removed soon. Please use
nf_conntrack.acct=1 kernel paramater, acct=1 nf_conntrack module option or
sysctl net.netfilter.nf_conntrack_acct=1 to enable it.
ctnetlink v0.93: registering with nfnetlink.
IPv4 over IPv4 tunneling driver
GRE over IPv4 tunneling driver
ip_tables: (C) 2000-2006 Netfilter Core Team
ClusterIP Version 0.8 loaded successfully
TCP cubic registered
Initializing XFRM netlink socket
NET: Registered protocol family 17
NET: Registered protocol family 15
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
802.1Q VLAN Support v1.8 Ben Greear <gree...@candelatech.com>
All bugs added by David S. Miller <da...@redhat.com>
SCTP: Hash tables configured (established 65536 bind 65536)
Using IPI No-Shortcut mode
drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
md: Waiting for all devices to be available before autodetect
md: If you don't use raid, use raid=noautodetect
md: Autodetecting RAID arrays.
md: Scanned 4 and added 4 devices.
md: autorun ...
md: considering sdb2 ...
md: adding sdb2 ...
md: sdb1 has different UUID to sdb2
md: adding sda2 ...
md: sda1 has different UUID to sdb2
md: created md2
md: bind<sda2>
md: bind<sdb2>
md: running: <sdb2><sda2>
md2: setting max_sectors to 128, segment boundary to 32767
raid0: looking at sdb2
raid0: comparing sdb2(722330496) with sdb2(722330496)
raid0: END
raid0: ==> UNIQUE
raid0: 1 zones
raid0: looking at sda2
raid0: comparing sda2(722330496) with sdb2(722330496)
raid0: EQUAL
raid0: FINAL 1 zones
raid0: done.
raid0 : md_size is 1444660992 blocks.
raid0 : conf->hash_spacing is 1444660992 blocks.
raid0 : nb_zone is 1.
raid0 : Allocating 4 bytes for hash.
md: considering sdb1 ...
md: adding sdb1 ...
md: adding sda1 ...
md: created md1
md: bind<sda1>
md: bind<sdb1>
md: running: <sdb1><sda1>
raid1: raid set md1 active with 2 out of 2 mirrors
md: ... autorun DONE.
md1: unknown partition table
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
VFS: Mounted root (ext3 filesystem) readonly.
Freeing unused kernel memory: 380k freed
r8169: eth0: link up
r8169: eth0: link up
Adding 5116692k swap on /dev/sda3. Priority:-1 extents:1 across:5116692k
Adding 5116692k swap on /dev/sdb3. Priority:-2 extents:1 across:5116692k
EXT3 FS on md1, internal journal
md2: unknown partition table
kjournald starting. Commit interval 5 seconds
EXT3 FS on md2, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
warning: `avahi-daemon' uses 32-bit capabilities (legacy support in use)
TCP: Treason uncloaked! Peer shrinks window 1690776753:1690793121. Repaired.
TCP: Treason uncloaked! Peer shrinks window 1749521463:1749526151. Repaired.
--
subprocess post-installation script returned error exit status 1: acpid: can't
open /proc/acpi/event: No such file or directory
https://bugs.launchpad.net/bugs/154887
You received this bug notification because you are a member of Ubuntu
Bugs, which is subscribed to Ubuntu.
--
ubuntu-bugs mailing list
ubuntu-bugs@lists.ubuntu.com
https://lists.ubuntu.com/mailman/listinfo/ubuntu-bugs
