bump! any updates? 2009/8/26 Ramaddan <ramad...@gawab.com>
> Still have this problem on Jaunty. > > Did not have this problem in Intrepid. > > This is the output I get in dmesg: > > [54237.142762] usb 1-1: configuration #1 chosen from 1 choice > [54237.166132] scsi10 : SCSI emulation for USB Mass Storage devices > [54237.169779] usb-storage: device found at 6 > [54237.169785] usb-storage: waiting for device to settle before scanning > [54242.169180] usb-storage: device scan complete > [54242.171276] scsi 10:0:0:0: Direct-Access Ext Hard Disk > PQ: 0 ANSI: 4 > [54272.284042] usb 1-1: reset high speed USB device using ehci_hcd and > address 6 > [54287.396554] usb 1-1: device descriptor read/64, error -110 > [54302.620102] usb 1-1: device descriptor read/64, error -110 > [54302.836555] usb 1-1: reset high speed USB device using ehci_hcd and > address 6 > ramad...@ramaddancomp:~$ dmesg | tail > [54466.984043] usb 2-1: new full speed USB device using ohci_hcd and > address 6 > [54482.160555] usb 2-1: device descriptor read/64, error -110 > [54497.440053] usb 2-1: device descriptor read/64, error -110 > [54497.716039] usb 2-1: new full speed USB device using ohci_hcd and > address 7 > [54502.736147] usb 2-1: device descriptor read/8, error -110 > [54507.857152] usb 2-1: device descriptor read/8, error -110 > [54508.136048] usb 2-1: new full speed USB device using ohci_hcd and > address 8 > [54513.157161] usb 2-1: device descriptor read/8, error -110 > [54518.277164] usb 2-1: device descriptor read/8, error -110 > [54518.380062] hub 2-0:1.0: unable to enumerate USB device on port 1 > > Any updates on this issue? > > -- > USB Hard Drive Not Accessible, vol_id hangs > https://bugs.launchpad.net/bugs/264789 > You received this bug notification because you are a direct subscriber > of the bug. > > Status in The Linux Kernel: Fix Released > Status in “linux” package in Ubuntu: Fix Released > Status in linux in Ubuntu Intrepid: Fix Committed > > Bug description: > I updated to 2.6.27-2 today, and one of my hard drives is no longer > recognized. It is in a Vantec NexStar GX enclosure, and was working fine on > .26, and continues to work fine on a Hardy machine. Here is the dmesg for > it: > > [ 6722.944029] usb 5-5: new high speed USB device using ehci_hcd and > address 27 > [ 6723.077863] usb 5-5: configuration #1 chosen from 1 choice > [ 6723.079511] hub 5-5:1.0: USB hub found > [ 6723.080345] hub 5-5:1.0: 4 ports detected > [ 6732.712034] usb 5-5: reset high speed USB device using ehci_hcd and > address 27 > [ 6733.124011] usb 5-5.1: new high speed USB device using ehci_hcd and > address 28 > [ 6733.364598] usb 5-5.1: configuration #1 chosen from 1 choice > [ 6733.365180] scsi17 : SCSI emulation for USB Mass Storage devices > [ 6733.365818] usb-storage: device found at 28 > [ 6733.365830] usb-storage: waiting for device to settle before scanning > [ 6738.364276] usb-storage: device scan complete > [ 6738.361002] scsi 17:0:0:0: Direct-Access ST340063 2A > 3.04 PQ: 0 ANSI: 0 > [ 6738.361002] sd 17:0:0:0: [sdm] 781422769 512-byte hardware sectors > (400088 MB) > [ 6738.361002] sd 17:0:0:0: [sdm] Write Protect is off > [ 6738.361002] sd 17:0:0:0: [sdm] Mode Sense: 03 00 00 00 > [ 6738.361002] sd 17:0:0:0: [sdm] Assuming drive cache: write through > [ 6738.361002] sd 17:0:0:0: [sdm] 781422769 512-byte hardware sectors > (400088 MB) > [ 6738.370354] sd 17:0:0:0: [sdm] Write Protect is off > [ 6738.370362] sd 17:0:0:0: [sdm] Mode Sense: 03 00 00 00 > [ 6738.370365] sd 17:0:0:0: [sdm] Assuming drive cache: write through > [ 6738.371516] sdm: sdm1 > [ 6738.418089] sd 17:0:0:0: [sdm] Attached SCSI disk > [ 6738.418995] sd 17:0:0:0: Attached scsi generic sg8 type 0 > [ 6738.656598] sd 17:0:0:0: [sdm] Sense Key : No Sense [current] > [ 6738.656614] sd 17:0:0:0: [sdm] Add. Sense: No additional sense > information > > >From there, the last 2 lines about Sense Key and Add Sense repeat over and > over again. > > The 4 port hub that is a part of the enclosure continues to work fine > though, with a floppy drive, a printer, and another hard drive. I have a > Vantec NexStar 3 enclosure as well, and it is working just fine. Dmesg for > the working enclosure: > > [ 4281.996024] usb 5-3: new high speed USB device using ehci_hcd and > address 19 > [ 4282.131863] usb 5-3: configuration #1 chosen from 1 choice > [ 4282.133222] scsi12 : SCSI emulation for USB Mass Storage devices > [ 4282.133561] usb-storage: device found at 19 > [ 4282.133566] usb-storage: waiting for device to settle before scanning > [ 4287.132002] usb-storage: device scan complete > [ 4287.136004] scsi 12:0:0:0: Direct-Access ST375064 0AS > PQ: 0 ANSI: 2 > [ 4287.138368] sd 12:0:0:0: [sdi] 1465149168 512-byte hardware sectors > (750156 MB) > [ 4287.144790] sd 12:0:0:0: [sdi] Write Protect is off > [ 4287.144800] sd 12:0:0:0: [sdi] Mode Sense: 38 00 00 00 > [ 4287.144804] sd 12:0:0:0: [sdi] Assuming drive cache: write through > [ 4287.152388] sd 12:0:0:0: [sdi] 1465149168 512-byte hardware sectors > (750156 MB) > [ 4287.154966] sd 12:0:0:0: [sdi] Write Protect is off > [ 4287.154975] sd 12:0:0:0: [sdi] Mode Sense: 38 00 00 00 > [ 4287.154979] sd 12:0:0:0: [sdi] Assuming drive cache: write through > [ 4287.154988] sdi: sdi1 > [ 4287.176965] sd 12:0:0:0: [sdi] Attached SCSI disk > [ 4287.177173] sd 12:0:0:0: Attached scsi generic sg7 type 0 > [ 4289.129138] kjournald starting. Commit interval 5 seconds > [ 4289.130101] EXT3 FS on sdi1, internal journal > [ 4289.130110] EXT3-fs: mounted filesystem with ordered data mode. > -- USB Hard Drive Not Accessible, vol_id hangs https://bugs.launchpad.net/bugs/264789 You received this bug notification because you are a member of Ubuntu Bugs, which is subscribed to Ubuntu. -- ubuntu-bugs mailing list ubuntu-bugs@lists.ubuntu.com https://lists.ubuntu.com/mailman/listinfo/ubuntu-bugs
