Public bug reported: Booting today's latest kernel in jaunty results in no ability to get dhcp addresses.
Upon manually disabling network daemon and a manual attempt I get: $sudo dhclient eth0 Internet Systems Consortium DHCP Client V3.1.2 Copyright 2004-2008 Internet Systems Consortium. All rights reserved. For info, please visit http://www.isc.org/sw/dhcp/ Open a socket for LPF: Operation not permitted dmesg reports: [ 23.180309] tg3: eth0: Link is up at 100 Mbps, full duplex. [ 23.180312] tg3: eth0: Flow control is on for TX and on for RX. [ 23.180728] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 23.240397] type=1503 audit(1249398688.677:10): operation="capable" pid=3017 parent=2652 profile="/sbin/dhclient3" name="net_raw" [ 34.108045] eth0: no IPv6 routers present [ 113.467852] type=1503 audit(1249398778.901:11): operation="capable" pid=3406 parent=2652 profile="/sbin/dhclient3" name="net_raw" [ 138.896564] tg3 0000:09:00.0: PME# enabled [ 140.765094] tg3 0000:09:00.0: PME# disabled [ 140.780365] tg3 0000:09:00.0: irq 29 for MSI/MSI-X [ 140.841974] ADDRCONF(NETDEV_UP): eth0: link is not ready [ 141.062798] Registered led device: iwl-phy0::radio [ 141.062977] Registered led device: iwl-phy0::assoc [ 141.064319] Registered led device: iwl-phy0::RX [ 141.064389] Registered led device: iwl-phy0::TX [ 141.104567] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 142.398005] tg3: eth0: Link is up at 100 Mbps, full duplex. [ 142.398012] tg3: eth0: Flow control is on for TX and on for RX. [ 142.399071] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 142.420763] type=1503 audit(1249398807.854:12): operation="capable" pid=3413 parent=2652 profile="/sbin/dhclient3" name="net_raw" [ 152.804051] eth0: no IPv6 routers present [ 157.844565] tg3 0000:09:00.0: PME# enabled [ 168.588801] tg3 0000:09:00.0: PME# disabled [ 168.601362] tg3 0000:09:00.0: irq 29 for MSI/MSI-X [ 168.663207] ADDRCONF(NETDEV_UP): eth0: link is not ready [ 169.675818] type=1503 audit(1249398835.109:13): operation="capable" pid=3420 parent=3375 profile="/sbin/dhclient3" name="net_raw" [ 170.219075] tg3: eth0: Link is up at 100 Mbps, full duplex. [ 170.219083] tg3: eth0: Flow control is on for TX and on for RX. [ 170.220284] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 175.843593] type=1503 audit(1249398841.277:14): operation="capable" pid=3427 parent=3375 profile="/sbin/dhclient3" name="net_raw" ** Affects: linux (Ubuntu) Importance: Undecided Status: New -- Open a socket for LPF: Operation not permitted https://bugs.launchpad.net/bugs/408907 You received this bug notification because you are a member of Ubuntu Bugs, which is subscribed to Ubuntu. -- ubuntu-bugs mailing list ubuntu-bugs@lists.ubuntu.com https://lists.ubuntu.com/mailman/listinfo/ubuntu-bugs
