Here is the lspci -vvnn from a boot with the WLAN module enabled and the
wl and ssb modules manually removed:

02:00.0 Network controller [0280]: Broadcom Corporation BCM4312 802.11a/b/g 
[14e4:4312] (rev 02)
        Subsystem: Hewlett-Packard Company Device [103c:1370]                   
                
        Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- 
Stepping- SERR+ FastB2B- DisINTx-
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- 
<MAbort- >SERR- <PERR- INTx- 
        Interrupt: pin A routed to IRQ 24                                       
                             
        Region 0: Memory at fdffc000 (64-bit, non-prefetchable) [size=16K]      
                             
        Capabilities: [40] Power Management version 3                           
                             
                Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA 
PME(D0-,D1-,D2-,D3hot-,D3cold-)                   
                Status: D0 PME-Enable- DSel=0 DScale=2 PME-                     
                             
        Capabilities: [58] Vendor Specific Information <?>                      
                             
        Capabilities: [e8] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 
Enable-                      
                Address: 0000000000000000  Data: 0000                           
                             
        Capabilities: [d0] Express (v1) Endpoint, MSI 00                        
                             
                DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <4us, L1 
unlimited                    
                        ExtTag+ AttnBtn- AttnInd- PwrInd- RBE+ FLReset-         
                             
                DevCtl: Report errors: Correctable- Non-Fatal- Fatal- 
Unsupported-                           
                        RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-            
                             
                        MaxPayload 128 bytes, MaxReadReq 128 bytes              
                             
                DevSta: CorrErr+ UncorrErr- FatalErr- UnsuppReq+ AuxPwr- 
TransPend-                          
                LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency 
L0 <4us, L1 <64us             
                        ClockPM+ Suprise+ LLActRep- BwNot-                      
                             
                LnkCtl: ASPM L0s Enabled; RCB 64 bytes Disabled- Retrain- 
CommClk-                           
                        ExtSynch- ClockPM+ AutWidDis- BWInt- AutBWInt-          
                             
                LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ 
DLActive- BWMgmt- ABWMgmt-           
        Capabilities: [100] Advanced Error Reporting <?>                        
                             
        Capabilities: [13c] Virtual Channel <?>                                 
                             
        Capabilities: [160] Device Serial Number 21-00-35-ff-ff-00-96-09        
                             
        Capabilities: [16c] Power Budgeting <?>                                 
                             
        Kernel modules: wl, ssb

-- 
[HP 2133] wl module causes hard lock
https://bugs.launchpad.net/bugs/384167
You received this bug notification because you are a member of Ubuntu
Bugs, which is subscribed to Ubuntu.

-- 
ubuntu-bugs mailing list
ubuntu-bugs@lists.ubuntu.com
https://lists.ubuntu.com/mailman/listinfo/ubuntu-bugs

Reply via email to