Public bug reported:
Upgraded an Hardy to Intrepid with ATI Technologies Inc RV570 [Radeon
X1950 Pro] (rev 9a) graphics card.
After installation X fails to start, even after removing xorg.conf. I had to
make a manual xorg.conf to get
any kind of X running. This would be a showstopper for beginners.
After that i installed the restricted driver, but still no 3D
acceleration available. Xorg log attached.
01:00.0 VGA compatible controller [0300]: ATI Technologies Inc RV570 [Radeon
X1950 Pro] [1002:7280] (rev 9a)
Subsystem: C.P. Technology Co. Ltd Device [148c:2223]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 255 (2000ns min), Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 11
Region 0: Memory at e0000000 (32-bit, prefetchable) [size=256M]
Region 1: I/O ports at e000 [size=256]
Region 2: Memory at fbe00000 (32-bit, non-prefetchable) [size=64K]
Expansion ROM at fbd00000 [disabled] [size=128K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] AGP version 3.0
Status: RQ=256 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans-
64bit- FW+ AGP3+ Rate=x4,x8
Command: RQ=1 ArqSz=0 Cal=0 SBA+ AGP- GART64- 64bit- FW-
Rate=<none>
Capabilities: [80] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0
Enable-
Address: 0000000000000000 Data: 0000
01:00.1 Display controller [0380]: ATI Technologies Inc RV570 [Radeon X1950
Pro] (secondary) [1002:72a0] (rev 9a)
Subsystem: C.P. Technology Co. Ltd Device [148c:2222]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64 (2000ns min), Cache Line Size: 64 bytes
Region 0: Memory at fbf00000 (32-bit, non-prefetchable) [size=64K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
** Affects: fglrx-installer (Ubuntu)
Importance: Undecided
Status: New
--
Radeon X1950 Pro X fails to start and no 3D-acceleration
https://bugs.launchpad.net/bugs/298838
You received this bug notification because you are a member of Ubuntu
Bugs, which is subscribed to Ubuntu.
--
ubuntu-bugs mailing list
ubuntu-bugs@lists.ubuntu.com
https://lists.ubuntu.com/mailman/listinfo/ubuntu-bugs
