Hello,
I'm quite new with Linux environment and I hope someone can help me with the problem I'm facing. I've installed RH 7.2 on my laptop (Toshiba Tecra 8000). I have to say that during the installation everything went fine, but when I had to install the ethernet card, installation process just skipped that phase. Then, I tried to configure it manually from the GUI control panel, but my card (Xircom CE3-10/100 Fast Ethernet) does not appear in the list. In var/log/messages I can see that cardmgr starts properly, but I get the error cardmgr[799]: config error, file './config.opts' line 8: no function bindings: Aug 29 23:05:10 localhost cardmgr[799]: starting, version is 3.1.22 Aug 29 23:05:10 localhost rc: Starting pcmcia: succeeded Aug 29 23:05:11 localhost cardmgr[799]: config error, file './config.opts' line 8: no function bindings Aug 29 23:05:11 localhost cardmgr[799]: watching 2 sockets Aug 29 23:05:11 localhost kernel: cs: IO port probe 0x0c00-0x0cff: clean. Aug 29 23:05:11 localhost kernel: cs: IO port probe 0x0100-0x04ff: excluding 0x220-0x22f 0x330-0x337 0x378-0x37f 0x388-0x38f 0x4d0-0x4d7 In /etc/pcmcia/config.opts I see that at that line there is the port range definition. Anyway, in the log later on I see that the card seems to be recognized correctly; irq=3, which is consistent to the entry in config.opts file: .... Aug 29 23:05:11 localhost cardmgr[799]: initializing socket 0 Aug 29 23:05:11 localhost kernel: cs: memory probe 0xa0000000-0xa0ffffff: clean. Aug 29 23:05:11 localhost cardmgr[799]: socket 0: Xircom CE3-10/100 Fast Ethernet Aug 29 23:05:11 localhost cardmgr[799]: executing: 'modprobe xirc2ps_cs' Aug 29 23:05:11 localhost kernel: xirc2ps_cs.c 1.31 1998/12/09 19:32:55 (dd9jn+kvh) Aug 29 23:05:11 localhost cardmgr[799]: executing: './network start eth0' Aug 29 23:05:11 localhost kernel: eth0: Xircom: port 0x300, irq 3, hwaddr 00:80:C7:48:04:2A Aug 29 23:05:12 localhost cardmgr[799]: initializing socket 1 Aug 29 23:05:12 localhost cardmgr[799]: socket 1: Serial or Modem Aug 29 23:05:12 localhost cardmgr[799]: executing: 'modprobe serial_cs' Aug 29 23:05:12 localhost cardmgr[799]: executing: './serial start ttyS1' Aug 29 23:05:12 localhost kernel: ttyS01 at port 0x02f8 (irq = 4) is a 16550A Aug 29 23:05:13 localhost xinetd[849]: chargen disabled, removing ..... In the PCMCIA Card Configuration Database (/etc/pcmcia/config) I also can see the card. Finally, the file pcmcia was originally like the following: PCMCIA=yes PCIC=yenta_socket PCIC_OPTS= CORE_OPTS= then I changed to: PCMCIA=yes PCIC=i82365 PCIC_OPTS= CORE_OPTS= and finally to: PCMCIA=yes PCIC=tcic PCIC_OPTS= CORE_OPTS= but the behavior is always the same; I really don't know what else I can do; when I query the cardmgr daemon it says that the cards (I have also a modem card not recognized, but this is another problem) are up and running and when I make a hot plug-in of the cards I can ear double beep. Any suggestions? Thanks for you help in advanced / Cheers ----------------------------------------------------- Invia una cartolina ad un amico! http://cartoline.supereva.it/index.html messaggio inviato con Freemail by www.superEva.it ----------------------------------------------------- -- redhat-list mailing list unsubscribe mailto:[EMAIL PROTECTED]?subject=unsubscribe https://listman.redhat.com/mailman/listinfo/redhat-list
