Thanks a lot. At least now I know that this combination works. Below is
output.
#ifconfig
eth0 Link encap:Ethernet HWaddr 00:50:DA:05:F5:FA
inet addr:24.113.219.210 Bcast:24.113.219.255 Mask:255.255.255.192
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:150 errors:0 dropped:0 overruns:0 carrier:0
collision:0 txqueuelen:100
Interrupt:10 Base address:0x300
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
UP LOOPBACK RUNNING MTU:3924 Metric:1
RX packets:90 errors:0 dropped:0 overruns:0 frame:0
TX packets:90 errors:0 dropped:0 overruns:0 carrier:0
collision:0 txqueuelen:0
#netstat -rn
Kernel IP routing table
Destination Gateway Genmask Flags MSS Window irtt Iface
24.113.219.210 0.0.0.0 255.255.255.255 UH 0 0 0 eth0
24.113.219.192 0.0.0.0 255.255.255.192 U 0 0 0 eth0
127.0.0.0 0.0.0.0 255.0.0.0 U 0 0 0 lo
0.0.0.0 24.113.219.193 0.0.0.0 UG 0 0 0 eth0
#traceroute 24.113.219.193
traceroute to 24.113.219.193 (24.113.219.193), 30 hops max, 38 byte packets
1 localhosts.localdomain (24.113.219.210) 3008.726 ms !H 3009.496 ms !H
3009.943 ms !H
>From: Edward Marczak <[EMAIL PROTECTED]>
>Reply-To: [EMAIL PROTECTED]
>To: <[EMAIL PROTECTED]>
>Subject: Re: 3c509b EtherLink III
>Date: Sat, 04 Mar 2000 20:47:55 -0500
>
>on 4/3/2000 3:30 PM, Dalibor Marceta shot down the bitstream:
>
> > I have Red Hat 6.1 and rogers@home. Network card is 3c509b. During
> > Installation only option I had was 3c509.
> > It seems working.
> > ifconfig -a ... gives me that network is up.
> > netstat -re gives me output for my IP, Netmask and Loopback (gateway
>listed
> > for them is * ???????) but it takes same time to show gateway address.
>
>What does the entry for 'default' show? Or if you netstat -rn, what does
>the 0.0.0.0 entry read?
>
> > I can ping my self and loopback but can't my gateway.
> > traceroute and ping for any address outside gives me
> > "Destination Host Unreachable"
> > Cablemodem seems working ... I can see lights flashing for OnLine Rx and
>Tx.
> >
> > How can I locate the problem? Any command which can help me? Any
>experience
> > or driver?
>
>I use the 509b in several machines and it does work just fine (yes, with
>the
>509 driver). Can you post your ifconfig and netstat -rn output?
>--
>Ed Marczak
>[EMAIL PROTECTED]
>
>
>--
>To unsubscribe: mail [EMAIL PROTECTED] with "unsubscribe"
>as the Subject.
>
______________________________________________________
Get Your Private, Free Email at http://www.hotmail.com
--
To unsubscribe: mail [EMAIL PROTECTED] with "unsubscribe"
as the Subject.
