All. I have a Creative Sound Blaster Audigy 2 and have been trying to use the latest cvs of emu10k1 to get it to work. I am almost there, but have one question.
I can hear sound from the digital port through the analog speakers, but cannot hear anything out of the analog port (3rd from the firewire port). emu-config -a makes no difference. Here i have posted my modules.conf file from /etc at the bottom of this email. as well as the Note that I have onboard motherboard Intel AC'97 sound that seems to be getting in the way as well, and the below shows how i tried to solve this by disabling it on the BIOS. Is there an issue with the drivers trying to access a port on the front case that is normally found on the Audigy 2 Platenum ??... my audigy 2 does not have this. My history to get it to work thus far... Have installed the kernel I wish to use along with the right kernel source. In this case 2.4.18-24.8.0. so /usr/src has a symlink called linux-2.4 which points to /usr/src/linux-2.4.18-24.8.0/. I also copied this to a symlink called linux in the same dir as people mentioned this might be useful. so ls on /usr/src is linux (a symlink to linux-2.4.18-24.8.0/) linux-2.4 (a symlink to linux-2.4.18-24.8.0/) linux-2.4.18-24.8.0/ Have configured the modules as follows. in /lib/modules i located config file in /lib/modules/2.4.18-24.8.0/configs. It was called kernel-2.4.18-i686.config. I copied this file to /lib/modules/2.4.18-24.8.0/ and called it .config as suggested by posts to this list. (Although someone told me you should not have to do this). Now I got the emu10k1 stuff from cvs and installed it using make all seemed ok so i did make again, all seemed fine, so then make install make tools make install-tools This all seemed fine On rebooting my system, I found that there was no sound. The system was trying to use the onboard sound which is an intel based AC'97 sound card. I then set this to be disabled on the BIOS and rebooted getting a message about missing hardware at startup.. on removing the configuration for this device ... the boot process goes ok and that is where i start getting sound out of the digital port. I would like to know how to get sound from the normal port. I would also like to know if it is a problem having the onboard sound device enabled with the BIOS. I.e. i want to have it enabled but not to use it in linux because I use it in another OS. what should i do for this? modules.conf from /etc/ alias parport_lowlevel parport_pc alias eth0 via-rhine alias usb-controller ehci-hcd post-install sound-slot-0 /bin/aumix-minimal -f /etc/.aumixrc -L >/dev/null 2>&1 || : pre-remove sound-slot-0 /bin/aumix-minimal -f /etc/.aumixrc -S >/dev/null 2>&1 || : alias sound-slot-1 audigy post-install sound-slot-1 /bin/aumix-minimal -f /etc/.aumixrc -L >/dev/null 2>&1 || : pre-remove sound-slot-1 /bin/aumix-minimal -f /etc/.aumixrc -S >/dev/null 2>&1 || : alias usb-controller1 usb-uhci alias ieee1394-controller ohci1394 alias sound emu10k1 emu10k1.conf from /ust/local/etc/ ## ## This file is used to configure emu10k1's emu-script ## CARD_IS_5_1=no USE_DIGITAL_OUTPUT=no ENABLE_TONE_CONTROL=yes # Note, it's safe to say yes to the next option even if you're not going # to use it. When this option is enabled, the driver can autodetects AC3 # data and behaves normally with normal audio. # (Saying yes causes some of the soundcard's resourses to be used up) AC3PASSTHROUGH=no # Change this to yes to enable the Livedrive midi port and IR remote # control. ENABLE_LIVEDRIVE_IR=no # Most Lives have their analog front signals inverted. If you have # problems with your setup (low bass), try changing this to 'yes'. (This # option has no effect with digital setups) INVERT_REAR=no #Multichannel playback (for 4 - 6 channel setups) MULTICHANNEL=yes # On 5.1 cards in multichannel mode, should the multichannel data be fed # to the sub as well? You probably don't want this if you have a # speaker set like the DTT2200 which already feeds all channels to the # sub in hardware. ROUTE_ALL_TO_SUB=no # By default, the front analog channels have a +12dB boost applied to # them by the AC'97 mixer. If you encounter clipping, or find that the # volume of the front speakers is too high in a multichannel setup, try # changing this to 'no'. ANALOG_FRONT_BOOST=no # Surround ################## # Some wavs, or mp3 are surround sound encoded the next two # options can be used to decode these in hardware. # (select on or the other, not both) # passive matrix surround decoder SURROUND=no # Active matrix surround decoder PROLOGIC=no # Extra Inputs ################# ## This connector is mounted on the card itself ENABLE_CD_Spdif=yes # Volume control is 'Digital1' in aumix/gmix/kmix # The next four inputs are found on Livedrives, some of these may also # be inputs on the older add-on daughter cards. ENABLE_OPTICAL_SPDIF=no # Volume control is 'Digital2' ENABLE_LINE2_MIC2=no # Volume control is 'Line2' ENABLE_RCA_SPDIF=no # Volume control is 'Digital3' ENABLE_RCA_AUX=no # Volume control is 'line3' -- redhat-list mailing list unsubscribe mailto:[EMAIL PROTECTED] https://listman.redhat.com/mailman/listinfo/redhat-list
