From: Shannon Zhao <[email protected]>
ACPI SPEC 5.0 defines GPIO-signaled ACPI Events for Hardware-reduced
platforms(like ARM). It uses GPIO pin to trigger an event to the guest.
For QEMU, here we add PL061 GPIO controller and use PIN 3 for
system_powerdown, reserving PIN 0, 1, 2 for PCI hotplug, CPU hotplug and
memory hotplug.
This patchset adds system_powerdown support on ARM through both ACPI and
DT ways. It adds a GPIO controller(here is PL061) in machine virt and
uses GPIO-singled event for ACPI while gpio-keys for DT. It can be
fetched from [1] and has been tested for the guests starting by ACPI or
DT while guests use systemd or acpid.
a) ACPI way. Since Graeme send a patchset to make ACPI on ARM64 support
amba device[2], it could use PL061 directly without modification to its
kernel driver code. In addition, we should use ACPI to start VM,
referring to below script. QEMU_EFI.fd can be fetched from [3].
qemu-system-aarch64 \
-smp 1 -m 1024 -M virt \
-cpu cortex-a57 -nographic \
-monitor telnet::4444,server,nowait \
-bios QEMU_EFI.fd \
-kernel Image \
-initrd guestfs.cpio.gz \
-append "rdinit=/sbin/init console=ttyAMA0 mem=512M root=/dev/ram
earlycon=pl011,0x9000000 rw acpi=force"
b) DT way. Start vm as usual.
qemu-system-aarch64 \
-smp 1 -m 1024 -M virt \
-cpu cortex-a57 -nographic \
-monitor telnet::4444,server,nowait \
-kernel Image \
-initrd guestfs.cpio.gz \
-append "rdinit=/sbin/init console=ttyAMA0 mem=512M root=/dev/ram
earlycon=pl011,0x9000000 rw"
Guest internal setup:
If your guest FS uses systemd, you should check file
/lib/udev/rules.d/70-power-switch.rules and add the following line in it
if it doesn't exist.
SUBSYSTEM=="input", KERNEL=="event*", SUBSYSTEMS=="platform",
ATTRS{keys}=="116", TAG+="power-switch"
If your guest FS uses acpid, you should check it has
/etc/acpi/powerbtn.sh and /etc/acpi/events/powerbtn. Refer to [4] for
the setup of acpid.
Thanks,
Shannon
[1]
https://git.linaro.org/people/shannon.zhao/qemu.git/shortlog/refs/heads/PowerButton_v2
[2] https://lkml.org/lkml/2015/9/30/392
[3] http://people.linaro.org/~shannon.zhao/ACPI_ARM/QEMU_EFI.fd
[4] https://wiki.linaro.org/LEG/Engineering/Kernel/ACPI/GPIOPowerButton
Changes since v2:
* rebased on upstream QEMU
* adjust irq signalling for PowerButton of PATCH 7/8 (Peter Maydell)
* Add several Reviewed-bys and Tested-bys from Wei Huang, thanks!
Changes since v1:
* rewrite GPIO Connection Descriptor (Michael)
Shannon Zhao (8):
hw/arm/virt: Add a GPIO controller
hw/arm/virt-acpi-build: Add GPIO controller in ACPI DSDT table
hw/arm/virt-acpi-build: Add power button device in ACPI DSDT table
hw/acpi/aml-build: Add GPIO Connection Descriptor
hw/acpi/aml-build: Add a wrapper for GPIO Interrupt Connection
hw/arm/virt-acpi-build: Add _E03 for Power Button
hw/arm/virt: Add QEMU powerdown notifier and hook it to GPIO Pin 3
hw/arm/virt: Add gpio-keys node for Poweroff using DT
hw/acpi/aml-build.c | 79 +++++++++++++++++++++++++++++++++++++++++++++
hw/arm/virt-acpi-build.c | 45 ++++++++++++++++++++++++++
hw/arm/virt.c | 59 +++++++++++++++++++++++++++++++++
include/hw/acpi/aml-build.h | 26 +++++++++++++++
include/hw/arm/virt.h | 1 +
5 files changed, 210 insertions(+)
--
2.1.0
