Hello,
I would like to run pulseaudio on our custom board with dm365 processor
(arm926ej-s core). After some patching I have the sound running with alsa
utils - I can use aplay and arecord commands and they works.
I compiled pulseaudio 1.1 using buildroot. Now when I run pulseaudio
deamon I'm getting these warnings
W: [pulseaudio] main.c: This program is not intended to be run as root
(unless --system is specified).
W: [pulseaudio] server-lookup.c: Unable to contact D-Bus:
org.freedesktop.DBus.Error.NotSupported: Using
X11 for dbus-daemon autolaunch was disabled at compile time, set your
DBUS_SESSION_BUS_ADDRESS instead
W: [pulseaudio] main.c: Unable to contact D-Bus:
org.freedesktop.DBus.Error.NotSupported: Using X11 for
dbus-daemon autolaunch was disabled at compile time, set your
DBUS_SESSION_BUS_ADDRESS instead
I do not have a X11 server on the board so I hope I can ignore these
warnings.
Unfortunately when I try to use paplay command to play a wav file I hear
no sound and it also never ends and has to be killed. The log from aplay
follows:
Opening a playback stream with sample specification 's16le 1ch 8000Hz' and
channel map 'mono'.
Connection established.
Stream successfully created.
Buffer metrics: maxlength=4194304, tlength=32000, prebuf=31682, minreq=320
Using sample spec 's16le 1ch 8000Hz', channel map 'mono'.
Connected to device alsa_output.platform-soc-audio.0.analog-stereo (0, not
suspended).
Stream started.
Time: 1.972 sec; Latency: 1984330 usec.
list-sinks in pacmd gives following info:
1 sink(s) available.
* index: 0
name: <alsa_output.platform-soc-audio.0.analog-stereo>
driver: <module-alsa-card.c>
flags: HARDWARE DECIBEL_VOLUME LATENCY FLAT_VOLUME DYNAMIC_LATENCY
state: SUSPENDED
suspend cause: IDLE
priority: 9009
volume: 0: 100% 1: 100%
0: 0.00 dB 1: 0.00 dB
balance 0.00
base volume: 100%
0.00 dB
volume steps: 65537
muted: no
current latency: 0.00 ms
max request: 0 KiB
max rewind: 0 KiB
monitor source: 0
sample spec: s16le 2ch 16000Hz
channel map: front-left,front-right
Stereo
used by: 0
linked by: 0
configured latency: 0.00 ms; range is 0.50 .. 2000.00 ms
card: 0 <alsa_card.platform-soc-audio.0>
module: 4
properties:
alsa.resolution_bits = "16"
device.api = "alsa"
device.class = "sound"
alsa.class = "generic"
alsa.subclass = "generic-mix"
alsa.name = ""
alsa.id = "generic stream generic-hifi-0"
alsa.subdevice = "0"
alsa.subdevice_name = "subdevice #0"
alsa.device = "0"
alsa.card = "0"
alsa.card_name = "DaVinci EYE03"
alsa.long_card_name = "DaVinci EYE03 (generic_codec)"
device.bus_path = "platform-soc-audio.0"
sysfs.path = "/devices/platform/soc-audio.0/sound/card0"
device.string = "hw:0"
device.buffering.buffer_size = "128000"
device.buffering.fragment_size = "8000"
device.access_mode = "mmap+timer"
device.profile.name = "analog-stereo"
device.profile.description = "Analog Stereo"
device.description = "DaVinci EYE03 Analog Stereo"
module-udev-detect.discovered = "1"
device.icon_name = "audio-card"
Could please someone here give me some advice how to get pulseaudio
working?
best regards
Jan
--
Tato zpráva byla vytvořena převratným poštovním klientem Opery:
http://www.opera.com/mail/
_______________________________________________
pulseaudio-discuss mailing list
[email protected]
http://lists.freedesktop.org/mailman/listinfo/pulseaudio-discuss
