hello,
I have an APC Smart-UPS-2200 which is connected via USB, as long as
I've followed the instructions in pkg-readme about disabling uhidev
and upd it's always worked fine. When I updated to the latest snap
(June 4th) however I am now always seeing "COMMLOST" in the output of
'apcaccess status' I tried booting the previous kernel (May 19th,
#1709), but that did not resolve it, it seems the breakage occurred
when apcupsd went from 3.14.13p1 to 3.14.13p2 which seems to have been
because the removal of USB_GET_STRING_DESC. I did try the newly
committed (but as yet unpackaged) 3.14.14 but no more luck there.
I tried to build 3.14.13p1 to see if I can confirm what broke it, but
I've been unable to succeed. I backed out the USB_GET_STRING_DESC
changes and built a new kernel based on sources from around
2016-05-20, I tried to do the same thing with the ports tree but
clearly I've missed something, because I never make it further than:
make[5]: Entering directory
'/usr/ports/pobj/apcupsd-3.14.13/apcupsd-3.14.13/src/drivers/usb/bsd'
CXX src/drivers/usb/bsd/hidutils.c
if test ! -d .obj; then mkdir -p .obj; fi
c++ -x c++ -I/usr/local/include
-I/usr/ports/pobj/apcupsd-3.14.13/apcupsd-3.14.13/src/libusbhid
-I/usr/ports/pobj/apcupsd-3.14.13/apcupsd-3.14.13/include -O2 -pipe
-fno-exceptions -fno-rtti -Wall -pthread -c -o .obj/hidutils.o hidutils.c
hidutils.c: In function 'const char* hidu_get_string(int, int)':
hidutils.c:354: error: 'USB_GET_STRING_DESC' was not declared in this scope
../../../../autoconf/targets.mak:141: recipe for target
'.obj/hidutils.o' failed
gmake[5]: *** [.obj/hidutils.o] Error 1
gmake[5]: Leaving directory
'/usr/ports/pobj/apcupsd-3.14.13/apcupsd-3.14.13/src/drivers/usb/bsd'
../../../../autoconf/targets.mak:55: recipe for target 'all' failed
gmake[4]: *** [all] Error 2
gmake[4]: Leaving directory
'/usr/ports/pobj/apcupsd-3.14.13/apcupsd-3.14.13/src/drivers/usb/bsd'
../../../autoconf/targets.mak:105: recipe for target 'bsd_DIR' failed
gmake[3]: *** [bsd_DIR] Error 2
gmake[3]: Leaving directory
'/usr/ports/pobj/apcupsd-3.14.13/apcupsd-3.14.13/src/drivers/usb'
../../autoconf/targets.mak:105: recipe for target 'usb_DIR' failed
gmake[2]: *** [usb_DIR] Error 2
gmake[2]: Leaving directory
'/usr/ports/pobj/apcupsd-3.14.13/apcupsd-3.14.13/src/drivers'
../autoconf/targets.mak:105: recipe for target 'drivers_DIR' failed
gmake[1]: *** [drivers_DIR] Error 2
gmake[1]: Leaving directory
'/usr/ports/pobj/apcupsd-3.14.13/apcupsd-3.14.13/src'
autoconf/targets.mak:105: recipe for target 'src_DIR' failed
gmake: *** [src_DIR] Error 2
*** Error 2 in . (/usr/ports/infrastructure/mk/bsd.port.mk:2675
'/usr/ports/pobj/apcupsd-3.14.13/.build_done')
*** Error 1 in /usr/ports/sysutils/apcupsd
(/usr/ports/infrastructure/mk/bsd.port.mk:2397 'all')
any clues?
Below is a dmesg from current, as well as output from usbdevs
and apcaccess.
thanks,
.jh
----
# dmesg
OpenBSD 6.0-beta (GENERIC) #1783: Sat Jun 4 20:02:48 MDT 2016
dera...@i386.openbsd.org:/usr/src/sys/arch/i386/compile/GENERIC
cpu0: Intel(R) Pentium(R) 4 Mobile CPU 1.70GHz ("GenuineIntel"
686-class) 1.20 GHz
cpu0:
FPU,V86,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUSH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PERF
real mem = 536240128 (511MB)
avail mem = 513286144 (489MB)
mpath0 at root
scsibus0 at mpath0: 256 targets
mainbus0 at root
bios0 at mainbus0: date 01/07/04, BIOS32 rev. 0 @ 0xffe90, SMBIOS rev.
2.3 @ 0xf76b0 (62 entries)
bios0: vendor Dell Computer Corporation version "A11" date 01/07/2004
bios0: Dell Computer Corporation Inspiron 8200
acpi0 at bios0: rev 0
acpi0: sleep states S0 S1 S3 S4 S5
acpi0: tables DSDT FACP
acpi0: wakeup devices LID_(S3) PBTN(S4) PCI0(S3) UAR1(S3) USB0(S1)
USB1(S1) USB2(S1) MODM(S3) PCIE(S3) MPCI(S3)
acpitimer0 at acpi0: 3579545 Hz, 24 bits
acpiprt0 at acpi0: bus 0 (PCI0)
acpiprt1 at acpi0: bus 1 (AGP_)
acpiprt2 at acpi0: bus 2 (PCIE)
acpiprt3 at acpi0: bus -1 (MPCI)
acpicpu0 at acpi0acpicpu0: struck PSS entry, core frequency equals last
acpicpu0: struck PSS entry, core frequency equals last
acpicpu0: invalid _PSS length
: !C2(@50 io@0x8e4), C1(@1 halt!)
acpipwrres0 at acpi0: PADA, resource for ADPT
acpitz0 at acpi0: critical temperature is 94 degC
acpiac0 at acpi0: AC unit online
acpibat0 at acpi0: BAT0 not present
acpibat1 at acpi0: BAT1 model "LIP8120DLP" serial 20216 type LION oem
"Sony Corp."
acpibtn0 at acpi0: LID_
acpibtn1 at acpi0: PBTN
acpibtn2 at acpi0: SBTN
"PNP0F13" at acpi0 not configured
"PNP0303" at acpi0 not configured
"PNP0700" at acpi0 not configured
"PNP0501" at acpi0 not configured
"PNP0401" at acpi0 not configured
acpidock0 at acpi0: GDCK not docked (0)
acpivideo0 at acpi0: VID_
bios0: ROM list: 0xc0000/0xf800 0xcf800/0x800!
cpu0 at mainbus0: (uniprocessor)
mtrr: Pentium Pro MTRR support, 8 var ranges, 88 fixed ranges
pci0 at mainbus0 bus 0: configuration mode 1 (bios)
pchb0 at pci0 dev 0 function 0 "Intel 82845 Host" rev 0x04
intelagp0 at pchb0
agp0 at intelagp0: aperture at 0xe8000000, size 0x4000000
ppb0 at pci0 dev 1 function 0 "Intel 82845 AGP" rev 0x04
pci1 at ppb0 bus 1
1:0:0: mem address conflict 0x80000000/0x20000
vga1 at pci1 dev 0 function 0 "NVIDIA GeForce4 440 Go" rev 0xa3
wsdisplay0 at vga1 mux 1: console (80x25, vt100 emulation)
wsdisplay0: screen 1-5 added (80x25, vt100 emulation)
uhci0 at pci0 dev 29 function 0 "Intel 82801CA/CAM USB" rev 0x02: irq 11
uhci1 at pci0 dev 29 function 2 "Intel 82801CA/CAM USB" rev 0x02: irq 11
ppb1 at pci0 dev 30 function 0 "Intel 82801BAM Hub-to-PCI" rev 0x42
pci2 at ppb1 bus 2
xl0 at pci2 dev 0 function 0 "3Com 3c905C 100Base-TX" rev 0x78: irq 11,
address 00:08:74:e3:08:86
exphy0 at xl0 phy 24: 3Com internal media interface
cbb0 at pci2 dev 1 function 0 "TI PCI4451 CardBus" rev 0x00: irq 11
cbb1 at pci2 dev 1 function 1 "TI PCI4451 CardBus" rev 0x00: irq 11
"TI PCI4451 FireWire" rev 0x00 at pci2 dev 1 function 2 not configured
cardslot0 at cbb0 slot 0 flags 0
cardbus0 at cardslot0: bus 4 device 0 cacheline 0x8, lattimer 0x20
pcmcia0 at cardslot0
cardslot1 at cbb1 slot 1 flags 0
cardbus1 at cardslot1: bus 5 device 0 cacheline 0x8, lattimer 0x20
pcmcia1 at cardslot1
ichpcib0 at pci0 dev 31 function 0 "Intel 82801CAM LPC" rev 0x02
pciide0 at pci0 dev 31 function 1 "Intel 82801CAM IDE" rev 0x02: DMA,
channel 0 configured to compatibility, channel 1 configured to compatibility
wd0 at pciide0 channel 0 drive 0: <HITACHI_DK23EB-40>
wd0: 16-sector PIO, LBA, 38154MB, 78140160 sectors
atapiscsi0 at pciide0 channel 0 drive 1
scsibus1 at atapiscsi0: 2 targets
cd0 at scsibus1 targ 0 lun 0: <HL-DT-ST, DVD-ROM GDR8081N, 0108> ATAPI
5/cdrom removable
wd0(pciide0:0:0): using PIO mode 4, Ultra-DMA mode 5
cd0(pciide0:0:1): using PIO mode 4, DMA mode 2
atapiscsi1 at pciide0 channel 1 drive 0
scsibus2 at atapiscsi1: 2 targets
cd1 at scsibus2 targ 0 lun 0: <TEAC, CD-W224E, L.0E> ATAPI 5/cdrom removable
cd1(pciide0:1:0): using PIO mode 4, DMA mode 2
auich0 at pci0 dev 31 function 5 "Intel 82801CA/CAM AC97" rev 0x02: irq
11, ICH3 AC97
ac97: codec id 0x4352595b (Cirrus Logic CS4205 rev 3)
ac97: codec features mic channel, tone, simulated stereo, bass boost, 20
bit DAC, 18 bit ADC, SRS 3D
audio0 at auich0
"Intel 82801CA/CAM Modem" rev 0x02 at pci0 dev 31 function 6 not configured
usb0 at uhci0: USB revision 1.0
uhub0 at usb0 "Intel UHCI root hub" rev 1.00/1.00 addr 1
usb1 at uhci1: USB revision 1.0
uhub1 at usb1 "Intel UHCI root hub" rev 1.00/1.00 addr 1
isa0 at ichpcib0
isadma0 at isa0
fdc0 at isa0 port 0x3f0/6 irq 6 drq 2
com0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
pckbc0 at isa0 port 0x60/5 irq 1 irq 12
pckbd0 at pckbc0 (kbd slot)
wskbd0 at pckbd0: console keyboard, using wsdisplay0
pms0 at pckbc0 (aux slot)
wsmouse0 at pms0 mux 0
pms0: ALPS Dualpoint, version 0x2222
wsmouse1 at pms0 mux 0
pcppi0 at isa0 port 0x61
spkr0 at pcppi0
lpt0 at isa0 port 0x378/4 irq 7
npx0 at isa0 port 0xf0/16: reported by CPUID; using exception 16
uhub2 at uhub0 port 1 "Genesys Logic USB2.0 Hub" rev 2.00/85.37 addr 2
ugen0 at uhub2 port 2 "American Power Conversion Smart-UPS 2200 FW:UPS
09.2 / ID=18" rev 2.00/1.06 addr 3
uplcom0 at uhub2 port 4 "Prolific Technology Inc. USB-Serial Controller
D" rev 1.10/4.00 addr 4
ucom0 at uplcom0
uhub3 at uhub1 port 1 "Genesys Logic USB2.0 Hub" rev 2.00/77.64 addr 2
uplcom1 at uhub3 port 1 "Prolific Technology Inc. USB-Serial Controller
D" rev 1.10/4.00 addr 3
ucom1 at uplcom1
uplcom2 at uhub3 port 2 "Prolific Technology Inc. USB-Serial Controller
D" rev 1.10/4.00 addr 4
ucom2 at uplcom2
uplcom3 at uhub3 port 3 "Prolific Technology Inc. USB-Serial Controller
D" rev 1.10/4.00 addr 5
ucom3 at uplcom3
uplcom4 at uhub3 port 4 "Prolific Technology Inc. USB-Serial Controller
D" rev 1.10/4.00 addr 6
ucom4 at uplcom4
vscsi0 at root
scsibus3 at vscsi0: 256 targets
softraid0 at root
scsibus4 at softraid0: 256 targets
root on wd0a (bde744ae38325c1c.a) swap on wd0b dump on wd0b
# usbdevs -v -d
Controller /dev/usb0:
addr 1: full speed, self powered, config 1, UHCI root hub(0x0000),
Intel(0x8086), rev 1.00
uhub0
port 1 addr 2: full speed, self powered, config 1, USB2.0 Hub(0x0608),
Genesys Logic(0x05e3), rev 85.37
uhub2
port 1 powered
port 2 addr 3: full speed, power 2 mA, config 1, Smart-UPS 2200
FW:UPS 09.2 / ID=18(0x0003), American Power Conversion(0x051d), rev
1.06, iSerialNumber AS1505230549
ugen0
port 3 powered
port 4 addr 4: full speed, power 100 mA, config 1, USB-Serial
Controller D(0x2303), Prolific Technology Inc.(0x067b), rev 4.00
uplcom0
port 2 powered
Controller /dev/usb1:
addr 1: full speed, self powered, config 1, UHCI root hub(0x0000),
Intel(0x8086), rev 1.00
uhub1
port 1 addr 2: full speed, self powered, config 1, USB2.0 Hub(0x0608),
Genesys Logic(0x05e3), rev 77.64
uhub3
port 1 addr 3: full speed, power 100 mA, config 1, USB-Serial
Controller D(0x2303), Prolific Technology Inc.(0x067b), rev 4.00
uplcom1
port 2 addr 4: full speed, power 100 mA, config 1, USB-Serial
Controller D(0x2303), Prolific Technology Inc.(0x067b), rev 4.00
uplcom2
port 3 addr 5: full speed, power 100 mA, config 1, USB-Serial
Controller D(0x2303), Prolific Technology Inc.(0x067b), rev 4.00
uplcom3
port 4 addr 6: full speed, power 100 mA, config 1, USB-Serial
Controller D(0x2303), Prolific Technology Inc.(0x067b), rev 4.00
uplcom4
port 2 powered
# apcaccess status
APC : 001,018,0471
DATE : 2016-06-06 15:36:05 -0400
HOSTNAME : example.com
VERSION : 3.14.13 (02 February 2015) openbsd
UPSNAME : atlas
CABLE : USB Cable
DRIVER : USB UPS Driver
UPSMODE : Stand Alone
STARTTIME: 2016-06-06 15:35:05 -0400
STATUS : COMMLOST
MBATTCHG : 5 Percent
MINTIMEL : 3 Minutes
MAXTIME : 0 Seconds
NUMXFERS : 0
TONBATT : 0 Seconds
CUMONBATT: 0 Seconds
XOFFBATT : N/A
STATFLAG : 0x05000100
END APC : 2016-06-06 15:55:03 -0400
